GX550 Rear Barrier Divider Net
“
Specifications:
- Product: Barrier Divider Net
- Compatibility: 2024 – newer Toyota J250 Landcruiser/GX550
- Installation Time: About 60 minutes
- Tools Required: Trim Panel removal tool, Metric sockets (10mm,
14mm), 1/2 Drive Ratchet wrench, Cordless drill with socket
adapter, 5mm Allen Driver - Hardware Included: C105RW (C1019 included for Full Height
Version)
Product Usage Instructions:
Step 1: Preparation
Tilt 2nd row seats down. Install the net with Raingler logo
facing the rear or in the desired direction.
Using a trim panel removal tool, remove the bolt cover at the
top of the side wall indentation covers above the wheel well cover.
Remove the 10mm bolt.
Reinstall with C105RW Large washer, Square anchor with tab,
small neoprene backed washer, and black socket head screw in order
as shown. Orient Square ring to face forward.
Step 2: Installation (Full Height Only)
Pop up the lower seat belt strap anchor plate cover. Remove the
14mm head bolt and install the C1015 Anchor plate with the slot
oriented upwards and towards the center of the cabin. Tighten as
shown.
Step 3: Net Installation
Hook net’s top straps to the ceiling handles in the back. Feed
between handle and headliner and into the buckles cam. Loosely draw
net up high but do not fully tighten until both sides are attached
and net is centered.
Install the side wall straps. This will be the bottom strap on
the Upper Barrier and Middle Strap on the Full Height Barrier.
Step 4: Final Installation
Center the barrier starting at the top handles straps, then the
lower straps and finally center straps if using a Full Height
Version. Double check that the 2nd row seat can fully seat if
running Full Height Barrier if desired.
Wrap and cover the buckles as shown in the provided video.
FAQ:
Q: Can I install the net with Raingler logo facing
forward?
A: Yes, the net can be installed with the Raingler logo facing
forward or in any desired direction.
Q: What should I do if my vehicle does not have handles in
desired locations?
A: If your vehicle lacks handles in desired locations, follow
the provided steps to install mounting points for better
fitment.
“`
2024 – newer Toyota J250 Landcruiser/GX550 Behind 2nd Row Seats Barrier Divider Net Install
(Both Upper and Full Height Barrier instructions are included)
NOTE: Many newer models have B-pillar handles and even overhead on the ceiling that can be used for some of the top mounting locations. Check to see if you prefer to use these factory locations as the nets typically have enough adjustment to allow for this option. If your vehicle does not have handles in desired locations or you prefer to install mounting points for better fitment, please follow the below steps.
IMPORTANT: READ INSTRUCTIONS FULLY BEFORE STARTING
Time: About 60 minutes
Tools: (may vary by vehicle)
1. Trim Panel removal tool. 2. Metric sockets: 10mm (14mm also required for full
height) 3. 1/2″ Drive Ratchet wrench as well as a cordless drill
with socket adapter is helpful. 4. 5mm Allen Driver
Hardware to use : C105RW (C1019 included for Full Height Version)
Let’s get started!
Tilt 2nd row seats down and normally install with Raingler logo facing to the rear but can be installed other direction too. Step 1
Using a trim panel removal tool, feed into small opening at top of side wall indentation covers, above the wheel well cover.
Remove bolt cover. And remove 10mm bolt.
866-905-7625 | Tech@RAINGLER.com | Raingler.com
Reinstall with C105RW Large washer, Square anchor with tab, small neoprene backed washer and black socket head screw in order as shown.
Orient Square ring to face forward.
Step 2
(Full Height Only): Grasp and pop up the lower seat belt strap anchor plate cover.
866-905-7625 | Tech@RAINGLER.com | Raingler.com
Remove the 14mm head bolt with ratchet wrench: Install the C1015 Anchor plate with the slot oriented upwards and towards center of cabin. Tighten as shown.
866-905-7625 | Tech@RAINGLER.com | Raingler.com
Step 3
Ready to install the net itself. Hook net’s top straps to the ceiling handles in back feeding between handle and headliner and then into the buckles cam. Open cam buckle by depressing tab and feed strap tapered end under opposite flat side. Loosely draw net up high but do nit fully tighten until both sides are attached and net is centered.
Install the side wall straps. This will be the bottom strap on the Upper Barrier and Middle Strap on the Full Height Barrier.
Install the Full Height Barriers Lower Anchor Plate straps.
866-905-7625 | Tech@RAINGLER.com | Raingler.com
Step 4
Center the barrier starting at the top handles straps, then the lower straps and Finally center straps if a Full Height Version. Double check that the 2nd row seat can fully seat if running Full Height Barrier if so desired. Wrap and cover of the buckles as shown in this short video.
Upper Barrier:
Full Height (shown with optional ceiling storage attic net)
Chek out our videos here:
https://vimeo.com/raingler
Thank you for purchasing Raingler Nets. If you have any questions please contact us,
we are here to help!
866-905-7625 | Tech@RAINGLER.com | Raingler.com
Documents / Resources
 |
Raingler GX550 Rear Barrier Divider Net [pdf] User Guide GX550, GX550 Rear Barrier Divider Net, Rear Barrier Divider Net, Barrier Divider Net, Divider Net |