RAEDIAN NORA Socket Variant
Specifications:
- Product Name: NORA SOCKET VARIANT
- Usage: EV Charging
- Installation Type: Wall-mounted
- Power Requirements: Refer to manual for specific details
- Compatibility: Refer to EV manual for compatibility
- Safety: Certified electricians for installation and servicing
Product Usage Instructions
Safety Precautions:
- Read and understand the entire installation manual before proceeding.
- Always follow local regulations and guidelines for EV charging.
- Ensure the charger is in good condition before installation.
- Switch off power before installation and avoid water exposure.
- Avoid installation near hazardous materials or electromagnetic interference.
- Protect the product from damage and do not attempt to repair it yourself.
Installation Process:
- Choose a suitable location as per the manual’s recommendations.
- Power down the circuit-breakers before installing the charger.
- Mount the charger securely on the wall in the designated area.
- Connect the charger to the power source following the provided instructions.
- Ensure all connections are secure and follow proper cable management.
Charging Guidelines:
- Only connect the charger to your electric vehicle, not other devices.
- Ensure proper ventilation and avoid extreme weather conditions during charging.
- Refer to your EV manual for specific charging instructions and compatibility details.
Maintenance and Troubleshooting:
- Regularly inspect the charger for any signs of damage or wear.
- If facing issues, contact a certified electrician for servicing.
- Follow the manual for resetting the PIN code as required.
FAQ
Q: Can I install the charger myself?
A: No, this product should only be installed, repaired, or serviced by certified electricians to ensure safety and compliance with regulations.
Q: Where can I find the PIN code for registration?
A: The PIN code is located on the front of the quick guide and on the back of the charger. Once registered in the APP, reset a new PIN code.
Safety Notice
It’s crucial to familiarize with this manual and abide by all safety precautions outlined, including those indicated by safety markings on the equipment.
- General safety first While this manual provides helpful guidance, it’s not exhaustive. Always prioritize general safety requirements, design, production, and established safety standards when operating the charger.
- Local regulations matter Follow the specific regulations and guidelines related to EV charging installation and usage in your region along with the instructions in this manual.
- Check before you install Never install or use a charger that appears defective, cracked, damaged, or malfunctioning. It’s better to be safe than sorry.
- Power down before install Switch off the power before installation. Before you touch the charger for any reason, turn off the upstream residual current operated circuit-breakers with integral over current protection (RCBO).
- Ensure proper installation Only install the charger in environments specifically mentioned in this manual. Think of it like building a house on the right foundation to avoid future problems.
- Keep water way Direct water exposure can damage the charger. Opt for a sheltered location for optimal performance and longevity.
- Avoid hazardous locations Never install the charger near or in areas with flammable materials like gasoline, explosives, chemicals, or steam. Treat it like keeping lighters away from fireworks for safety!
- Avoid electromagnetic interference Strong magnetic fields and wireless transmitters can disrupt the charging process. Choose a location free from such interference.
- Seek shade Direct sunlight can impact the charger’s performance. Opt for a shaded area for efficient charging.
- Extreme weather warning Extreme weather conditions, like heavy rain, snow, or scorching heat, can compromise the charger’s functionality. Avoid using it in such circumstances.
- EV manual matters Before charging your specific electric vehicle with this product, always consult its manual for any additional safety instructions or compatibility detail.
Protecting the Product
- Keeping safety marks, warning signs, nameplates, and cabling marks intact ensures you have readily available safety information.
- Never insert fingers or sharp objects into any product component. Curiosity can lead to injury.
- Don’t submerge the charging connector in water.
- Resist the urge to disassemble, repair, or modify the product yourself.
- Avoid dropping, squeezing, or piercing the product.
- Don’t fold, crush, or damage any component with sharp objects.
Stick to your vehicle Only connect the charger to a vehicle, not other devices. Mixing and matching can lead to trouble or damages.
WARNING
This product shall only be installed, repaired or serviced by certified electricians. All applicable local, regional and national regulations for electrical installations must be followed strictly.
Notice of PIN Code
The PIN code is required for the charger register in the APP and located on the front of the quick guide, and on the back of the charger. Once the charger is registered in the APP, please reset a PIN Code.
The information in this document may be subject to change without prior notice. © Copyright 2024 RAEDIAN. All rights reserved.
Product overview
Accessories
Specification
Installation planning
Household grid system evaluation
The installer needs to evaluate the available electrical capacity at the installation site to ensure that it can handle the installation of an EV charger. Protection limit is based on max. 80% of the fuse rating, which can be set in the RAEDIAN APP.
| Rated Power | Earthing System | Voltage | Max. charging current |
| 7KW | TT, TN, IT | 230VAC ±20%, 50/60Hz | 32 Amp |
| 22KW | TT, TN, IT | 230/400VAC ±20%, 50/60Hz | 32 Amp |
RCD requirement
- A Residual current monitor device is integrated inside the charger, the charger will stop charging in case residual current exceeding 6mA d.c. is detected, according to IEC 62955.
- The RCD is automatically tested between each charging session.
- The integrated RCD has no influence on the function of external protective devices.
An external RCBO is required shown as below.
| Input | Specification | Remark |
| Single phase | 2P, 40A RCBO, at least Type A, Characteristic B/C |
50 Amp is recommended if the ambient temperature is higher than 40°C |
| Three phase | 4P, 40A RCBO, at least Type A, Characteristic B/C |
Recommend cable size
| Rated Power | Max. charging current | Cross sectional area |
| 7KW | 32A | 6mm² to 10mm² |
| 22KW | 32A | 6mm² to 10mm² |
Suggested Installation Tools
Installation instructions
Positioning
- Ensure that the installation surface is solid enough to hold the charger. It is recommended that the wall have a bearing capacity of at least 100 kg.
- Place the backplate on the wall, keep it horizontal, and use a marker/pencil to mark the hole drilling positions on the wall.
Mounting
- Use an electric drill to open four holes in the wall at the marked positions, the recommended depth and diameter, Insertion depth: 50 mm; φ8mm.
- Insert four plastic anchors into four openness.
- Use four wall-mounting screws to fasten the wall bracket.
- Hang the charger on the wall bracket.
- Use two security screws to tighten the device.
- Plug into CEE socket
Installation Acceptance Inspection
Power On
Power on the charger. The logo LED will be steady on after booting.
LED indicators
| Status | Logo LED Description | Status LED Description |
| Standby, available for charging | White, steady | Off |
| Cable plugged in, waiting for authorization or waiting for EV | Blue, steady | Blue,running |
| Charging in progress | Cyan, breathing | Cyan, breathing |
| Charging complete | Cyan, steady | Cyan, steady |
| Error | White, steady | Red, steady |
EV Charging test
- Plug in the charging cable on the EV and the charger.
- Charging session will start immediately with safe start current of 10 Amp.
- To change the access and the charging current of the charger,please follow the next step to connect with your phone.
Connect with your phone
Scan the following QR code and download RAEDIAN APP. Open the Bluetooth of your mobile phone and get close to the charger and get connected.
Scan the QR code
Find out more about Nora’s APP
Zhejiang Raedian New Energy Technology Co., Ltd
No.3, Shuangbai Road, Yuanhua Town,Haining City, 314416 Zhejiang
China
Documents / Resources
 |
RAEDIAN NORA Socket Variant [pdf] Instruction Manual NORA Socket Variant, NORA, Socket Variant, Variant |
 |
RAEDIAN NORA Socket Variant [pdf] Instruction Manual NORA Socket Variant, NORA, Socket Variant, Variant |