CrossFlight-CE Flight Controller
“
Specifications
- Dimension: 39.7*39.7*13mm
(1.56*1.56*0.52) - Weight: 16.5g (0.58oz), 54g (1.9oz when all
the connect wires included) - Hardware Sensor:
- Processor: HC32F4A0PITB QMI8658A
- Gyro & Accelerometer
- Compass: VCM5883L
- Barometer: SPA06-003
- OSD Chip FRAM: AT7456E
- Buzzer: 1
- Safety Switch: None
- Connector Type: JST GH 1.25 Connector
- PWM Output: 10 PWM Output
- Mavlink UART: 2 (Without CTSRTS)
- USB Port: 1 (Type-C)
- Signal Input: PPM/SBUS/CRSF
- RSSI Output: Support
Product Usage Instructions
1. Connecting CrossFlight-CE to Different Model Types
Follow the connection diagrams provided in the manual for
connecting CrossFlight-CE to multicopters, fixed-wing aircraft,
helicopters, and other compatible models.
2. Firmware Upgrade
To upgrade the firmware of CrossFlight-CE, ensure to download
the firmware only from RadioLink sources and follow the
instructions provided.
3. Power Module Specifications
Refer to the power module specifications for adaptable models
and operating parameters including ESC protocols, input voltage,
output voltage, and current details.
4. OSD Module Integration
CrossFlight-CE features an integrated OSD module. Configure and
utilize the OSD module as needed for displaying crucial flight
data.
FAQs (Frequently Asked Questions)
Q: Can CrossFlight-CE be used with submarines?
A: Yes, CrossFlight-CE is adaptable to submarines along with
other model types mentioned in the manual.
Q: How can I contact support for further assistance?
A: For any questions or support, you can reach out by sending
messages or leaving comments on Facebook and YouTube, or via email
at after_service@radiolink.com.cn.
“`
CrossFlight-CE
Quick Start Guide
Thank you for choosing RadioLink product. This product is not a toy and is not suitable for children under the age of 14. Adults should keep the product out of the reach of children and exercise caution when operating this product in the presence of children.
Note: In order to fully know about the usage of CrossFlight-CE and ensure flight safety, please download the detailed instruction manual from www.radiolink.com.cn/crossflightce_user_manual Read carefully and set the device as instructed. If there is any question, please send messages/ leave comments on Facebook and YouTube or send mails to after_service@radiolink.com.cn.
* CrossFlight-CE is adaptable to multirotor, airplane, helicopter, car, boat, submarine, radartracker and robot. * CrossFlight-CE can only upgrade the firmware from RadioLink.
firmware. The default firmware is for Multicopter. * CrossFlight-CE can set parameters by RadioLink Mission Planner, ArduPilot Mission Planner, and QGC Mission Planner. * CrossFlight-CE can upgrade the firmware by both RadioLink Mission Planner and ArduPilot Mission Planner (Firmware can only be installed by loading custom firmware ). CrossFlight-CE firmware download link: www.radiolink.com.cn/crossflightce_firmware Note: Make sure the power module is insulated from the metal or carbon fiber frame.It is strongly advised NOT to remove the shell. Otherwise the barometer might malfunction.
1
Connection Diagram of CrossFlight-CE to Different Model Types
CrossFlight-CE to Multicopter
2
CrossFlight-CE to Fixed-Wing
3
CrossFlight-CE to Helicopter
4
Packing List 5
Weight & Dimension
Specifications
Dimension
39.7*39.7*13mm (1.56″*1.56″*0.52″)
Weight
16.5g (0.58oz), 54g (1.9oz when all the connect wires included)
Hardware Sensor
Processor
Gyro & Accelerometer
HC32F4A0PITB QMI8658A
Compass
VCM5883L
Barometer
SPA06-003
OSD Chip FRAM
AT7456E
Without FRAM, use the internal flash to store parameters, 2617 waypoints for multicopters, and 2623 waypoints for airplanes/ cars/boats.
Buzzer
1
Safety Switch
None
Connector
Type
JST GH 1.25 Connector
PWM Output
10 PWM Output
Mavlink UART
2 (Without CTSRTS)
USB Port
1 (Type-C)
GPS UART / I2C Port 1
Signal Input
PPM/SBUS/CRSF
RSSI Output
Support
OSD Module
6
OSD Module integrated
Power Module Specifications
Adaptable Models Operating Parameters
ESC Protocol RTK Weight
PWM, DShot, and OneShot Protocol Support 16.5g (0.58oz) without wire
Input Voltage
2-12S
Maximum Detection Current
Output Voltage (BEC) Output Current (BEC) Single ESC Maximum Detection Current
90A 5.3V±0.2V 2A 22.5A
Airplane/2-8 Copters/Helicopter/Car/Boat/Submarine/ Radartracker/Robot
USB Voltage
5V±0.3V
Servo Voltage Operating
Not applicable -30~85
7
Documents / Resources
 |
RadioLink CrossFlight-CE Flight Controller [pdf] User Guide CrossFlight-CE Flight Controller, Flight Controller, Controller |