Radioddity RHS-H1 Hotspot D-Star Multi Mode IP Gateway
Specifications
- 802.11 b/g/n wireless LAN
- Quad-Core A53 1GHz
- 512MB RAM
- Micro USB power installed
- JumboSPOT UHF(430-440)+VHF(144-146) (VHF is not the main band, performance reduction)
- RF extend board
- 8G TF CARD Installed
- PI-STAR panel supports DMR, YSF,P25, D-STA,R and NXDN mode to QSO with RF To internet
- OLED Display
Product Usage Instructions
Step 1: MMDVMHost Configuration
Only Select DMR to Test.
Step 2: MMDVM Display Type
Select OLED.
Step 3: Apply Changes
Step 4: General Configuration
Type your call sign, your DMR ID, and radio frequency.
Step 5: Radio / Mode Type
Select STM32-DVM / MMDVM_SH – Raspberry PI Hat(GPIO).
Step 6: Apply Changes
For more technical support, visit www.MMDVMHost.sdr.kim
Frequently Asked Questions
- Q: How do I set up my DMR radio to communicate with the HOTSPOT?
- A: Your DMR radio must input the Talk Group and Frequency. More information can be found at http://www.pistar.uk
- Q: What should I do if I encounter issues with the HOTSPOT?
- A: You can install the Pi-star IMAGE file to the TF card again. Visit http://www.pistar.uk/downloads/ for more information and to download the necessary files.
For technical support, you can also visit www.MMDVMHost.sdr.kim
HOTSPOT is DMR,YSF,P25,D-STAR Multi Mode IP Gateway QSO anywhere come with Raspberry Pi ZERO W + hotspot (UHF+VHF main band) + TF8g + Antenna433mhz
Specifications
- 802.11 b/g/n wireless LAN
- Quad-Core A53 1GHz
- 512MB RAM
- Micro USB power installed JumboSPOT UHF(430-440)+VHF(144-146) (VHF is not the main band, performance reduction)RF extend board
- 8G TF CARD Installed PI-STAR panel
- Support DMR, YSF,P25, D-STA,R, and NXDN mode to QSO with RF To internet
- OLED Display
visit http://www.pistar.uk/wifi_builder.php input your home ssid and psk ,then download the wpa_supplicant.conf inside it has your home ssid and psk, then save to TF card, ROOT root directory example F:\ then power on it ,wait 2-3minutes, it will auto connect your home’s SSID, you can check your wifi router to see the pi-star host connected and it’s ip. also you can use your pc to ping pi-star,if successful,you can open http://pi-star or your pi-star’s ip default login user ispi-star, pass is raspberry, then login to SET your CALLSIN, ID, FREQ, and Modem, like the picture:
- Step1: MMDVMHost Configuration Only Select DMR to Test
- Step2: MMDVM Display Type: Select OLED
- Step3: Apply Changes
- Step4: General Configuration Type your call sign your dmr id radio freq
- Step5: Radio / Mode Type: Select STM32-DVM / MMDVM_SH – Raspberry PI Hat(GPIO)
- Step6: Apply Changes
also, your DMR radio must input the Talk Group and Freq, then you can talk now. More info
- http://www.pistar.uk
- http://www.pistar.uk/dmr_bm_talkgroups.php
- if you have a problem you can install the pi-star IMAGE file to TF card again :
- http://www.pistar.uk/downloads/
- http://www.pistar.uk/downloads/Pi-Star_RPi_V3.4.11_17-Mar-2018.zip
Technical support www.MMDVMHost.sdr.kim
Documents / Resources
 |
Radioddity RHS-H1 Hotspot D-Star Multi Mode IP Gateway [pdf] Instruction Manual RHS-H1 Hotspot D-Star Multi Mode IP Gateway, RHS-H1, Hotspot D-Star Multi Mode IP Gateway, Multi Mode IP Gateway, Mode IP Gateway, IP Gateway |
