RAB PLT-15-O-8FA-BYP Plt Omni Bypass Lamp
Specifications
- Model Numbers: PLT-15-O-8FA-BYP, PLT-17-O-8FA-BYP
- Compatibility: Can replace 32W and 42W CFL lamps with GX24q, G24d, and GX24d bases
- Installation: Retrofit kit for 2 PIN HORIZONTAL & VERTICAL MOUNT
INSTALLATION
Before starting the installation process, ensure that you have read and understood all the instructions provided in the manual.
- Read all WARNINGS before continuing this section.
- Ensure fixture is powered by 120-277V.
- Make sure POWER IS TURNED OFF AT THE SOURCE.
- Remove lens if applicable, remove cover and fluorescent lamp.
- Before rewiring, check the ballast type and refer to the relevant diagram.
- Before rewiring, check the number of lamps per fixture and refer to the relevant diagram.
- If fixture is new without ballast please refer to Fig.1.
- If fixture ballast type is electronic please refer to Fig. 2.
- If fixture ballast type is magnetic please refer to Fig. 3.
- This device is powered by two pins; Install lamp into the wired lampholder end.
- Visibly affix ‘Modificion Sticker’ and reinstall housing cover and lens if applicable.
- Select desired color temperature (Do not select when power on).
- Return power back to source and installation is now complete.
WIRING DIAGRAM
Follow the wiring diagram below based on your fixture type:
- Cut all wires that connect the ballast. Cut wire away from the lampholder.
- Rewire the power source directly to wires leading to lampholders.
- The lampholder should be shunted.
- If using with a magnetic ballast, the PLC can function as a plug & play lamp.
- If the ballast is not compatible, it can be bypassed, and the lamp can run directly off line voltage.
- New fixture without ballast wiring
- Electronic ballast fixture wiring
- Magnetic ballast fixture wiring modification
Easy Answers
- Website: rablighting.com
- Tech Help Line: Call our experts at 888-722-1000
- Email: Sales inquiries answered promptly at sales@rablighting.com
RAB Warranty:
RAB’s warranty terms and conditions can be found at rablighting.com/warranty.
Free Lighting Layouts:
Get lighting layout assistance online or by request.
IMPORTANT
- READ CAREFULLY BEFORE INSTALLING LAMPS. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
- RAB lamps must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION C ODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. - WARNING: Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Installation should be performed only by a qualified electrician in accordance with the National Electrical Code and relevant local code.
- Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.
- CAUTION: Disconnect power at the source before installation, inspection or removal. Do not simply switch off fixture.
- This item is rated at 120-277V. Installer must determine whether line voltage 120-277V is available at the luminaire before installation.
- Not intended for use with emergency exit fixtures or emergency exit lights.
- Not for use with luminaire ballast.
- Do not use if product is damaged.
- This lamp is non-dimmable. Not for use with dimmers.
- “This luminaire has been modified to operate LED lamps” shall be marked on the retroft luminaire where readiy visible by the user during normal maintenance including re-lamping.
- Risk of fire or electric shock. Do not open or modify. No user serviceable parts inside.
- The unit is intended to retrofit maximum 2 lamps.
- SUITABLE FOR DAMP LOCATIONS. Suitable for use in wet locations when used in an outdoor-rated fixture. Not for use where directly exposed to the weather or water.
FCC STATEMENT
Complies with Part 15 of the FCC.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received including interference that may cause undesired operation.
SUITABLE FOR “TYPE NON-IC” LUMINAIRES WITHOUT DIFFUSER WITH THROUGH-BRANCH WIRING MARKED “MAX. 4 12AWG CONDUCTORS.”
No external weight or mechanical force should be applied to lamp or components.
NOTE: This retroFIt kit is for a 2 PIN HORIZONTAL & VERTICAL MOUNT and can replace 32W and 42W CFL lamps with GX24q, G24d and GX24d bases.
RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
- Easy Answers
rablighting.com - Visit our website for product info, Tech Help Line
Call our experts: 888 722-1000 - e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty.
Documents / Resources
 |
RAB PLT-15-O-8FA-BYP Plt Omni Bypass Lamp [pdf] Instructions PLT-15-O-8FA-BYP, PLT-15-O-8FA-BYP Plt Omni Bypass Lamp, Plt Omni Bypass Lamp, Omni Bypass Lamp, Bypass Lamp, Lamp |