RAB Lightcloud Powerful Lighting Control System

Specifications

  • Brand: Lightcloud
  • Product Name: Lightcloud Blue
  • Compatibility: Lightcloud Blue mobile app
  • Maximum Devices per Account: 38,400
  • Maximum Devices per Site: 600
  • Maximum Devices per Area: 200
  • Maximum Subgroups per Area: 15
  • Mobile Device Compatibility: Apple (iOS) and Android
  • Wireless Technology: Bluetooth Mesh

Getting Started

To begin using the Lightcloud Blue system, follow these steps:

  1. Download the Lightcloud Blue mobile app from the Apple App Store or Google Play Store.
  2. Create a user account and log in to the app.
  3. Follow the on-screen instructions to set up your devices and connect them to the app.

Device Control

The Lightcloud Blue system allows you to control various devices such as dimmers, sensors, and smart plugs. Use the mobile app to adjust settings, create schedules, and monitor energy usage.

Nano Setup

If you have the Lightcloud Blue Nano, you can connect it to virtual assistant systems like Amazon Alexa or Google Home by following the provided instructions.

Wireless Remote

The wireless remote included with the Lightcloud Blue system provides convenient control over your devices. Ensure it is paired correctly with your devices for seamless operation.

FAQs

Are Lightcloud Enterprise devices compatible with the Lightcloud Blue mobile app?
Lightcloud Enterprise and Lightcloud Blue are separate platforms with their own compatible devices and control platforms. You can add the XDIM Bridge to connect Lightcloud Blue devices to a Lightcloud Enterprise Gateway for integration.

Illuminates when the device receives a
message and indicates the strength of
the signal

Package Content


3 – Best signal
2 – Acceptable signal
1 – Unacceptable signal
Consult the “Finding a Location” section
for more information
5
STATUS INDICATOR
SIGNAL INDICATOR
Confirm Device Connectivity
• Illuminated when device is powered
• Press once to highlight this device in the
Lightcloud Application

• Press twice and hold to set dim level
Press twice to toggle circuit on and of
• Press and hold for 10 seconds to remove
this device from a Lightcloud network
• Blinks when device is indicated from the
Lightcloud ApplicationOperating Modes
All configuration of Lightcloud products may be performed using the
Lightcloud web or mobile application, or by calling RAB.
CONTROLLER Provides switching and dimming for a single zone
TRIGGER Detect when an attached circuit is open or closed. For example,
you could attach the Controller in Trigger mode to an existing occupancy
sensor to allow your Lightcloud system to react to the sensor.REPEATER: Disables zone control and power measurement, and
extends the range of your network.


POWER MEASUREMENT: The Lightcloud Controller is capable of
measuring the power usage of the attached circuit. In order to utilize
this function, the neutral wire of the load must be connected to the
white-red sense wire. If the Switched Neutral line cannot be used, it
should be tied to the regular neutral wires (i.e. all neutral wires joined).


POWER LOSS DETECTION: If mains power to the Controller is lost,
the device will detect this and alert the Lightcloud application.

EMERGENCY DEFAULT: If communication is lost, the Controller may
optionally fall back to a specific state, such as turning the attached
circuit onFCC Information:


This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.

Note: This device has been tested and found to comply with the limits for
Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential environment. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to
radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment of and on, the user is encouraged to try and correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diferent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with the FCC’s RF exposure limits for general population /
uncontrolled exposure, this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter.
CAUTION: Changes or modifications to this equipment not expressly
approved by RAB Lighting may void the user’s authority to operate
this equipment.
© RAB Lighting, Inc
170 Ludlow Avenue Northvale, NJ 07647
Custom manufactured in China
1 (844) LIGHTCLOUD
1 844-544-4825
support@lightcloud.com
Lightcloud is a commercial
wireless lighting control system
& service. It’s powerful and
flexible, yet easy to use
and install. LeInput: 120-277VAC, 50/60Hz
Switching Capacity (Magnetic, Electronic Ballast or LED)
15.5A (120-277VAC)
277VAC: 20A Magetic/Resistive
240VAC: 5A Tungsten/Electronic, 20A FLA/60 LRA, 2HP
120VAC: 15A Tungsten, 1HP
Switched Neutral: The “Switched Neutral” white with red stripe wire is the neutral line for the load being
switched. This enables power measurement. Input: 120-277VAC, 50/60Hz
Purple: 0-10V positive
Grey: 0-10V common
Switching Capacity (Magnetic, Electronic Ballast or LED)
15.5A (120-277VAC)
277VAC: 20A Magetic/Resistive
240VAC: 5A Tungsten/Electronic, 20A FLA/60 LRA, 2HP
120VAC: 15A Tungsten, 1HP
Switched Neutral: The “Switched Neutral” white with red stripe wire is the neutral line for the load being
switched. This enables power measurement.
Note: The National Electrical Code requires that low-voltage wiring use in the same enclosure as
high-voltage wiring have an equal or better insulation rating. You may need to complete your low-voltage
wiring in another enclosure or use a partition.

 

Documents / Resources

RAB Lightcloud Powerful Lighting Control System [pdf] Instruction Manual
Nano, Wireless Remote, Dimmers, XDIM Bridge, Sensors, SmartShift, EV Charger, Lightcloud Powerful Lighting Control System, Lightcloud, Powerful Lighting Control System, Lighting Control System, Control System, System

References

Leave a comment

Your email address will not be published. Required fields are marked *