R and G LP0376BK Licence Plate Bracket
Specifications
- Model: LP0376BK
- Main Components: Main Bracket, Number Plate Light, Connector, Rubber Bung, Bolts, Washers, Nuts, Heat Shrink, License Plate Light, Self-Adhesive Foam
Fitting Instructions
Disassembly of OEM Tail Unit:
- Disconnect the wiring connector going to the OEM number plate light unit located under the passenger seat.
- Remove the OEM tail unit via the four bolts on the tail unit/undertray of the motorcycle.
- Unscrew all visible bolts on the OEM Tail Unit, disassemble the unit, and remove the OEM indicators for later use.
- Remove the sub-loom for use with the R&G tail tidy.
- Reassemble the OEM Tail unit without the indicators and store it away safely.
Tail Tidy Assembly
- Insert the supplied rubber bung into the hole on the tail tidy bracket.
- If required, cut the supplied self-adhesive foam strips to a similar size shown in the assembly diagram and stick in the position shown.
- Fasten the supplied R&G number plate light to the tail tidy assembly.
- Bolt the OEM indicators onto the tail tidy using the supplied Nyloc nuts and washers with the OEM bolts.
Continue with instructions on Page 5 of 5 from the manual for further steps in fitting the product.
- This kit contains the items pictured and labelled over page.
- Some parts may be shown for clarity of instructions only.
- Do not proceed until you are sure all parts are present.
- Please read all instructions before proceeding.
- IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE THEM FITTED BY A QUALIFIED TECHNICIAN.
- Please note that the way the kit is packed does not necessarily represent the way of mounting it to the bike.
- In the event of rubber washers being used to hold components onto bolts, these rubber washers can be thrown away.
| TOOLS REQUIRED
· A set of metric Hex keys to include 5mm & 6mm. · A set of metric sockets and wrenches. To include 8mm, 10mm & 12mm. · Cable cutters |
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm M5 BOLT = 12Nm M6 BOLT = 15Nm M8 BOLT = 20Nm M10 BOLT = 40Nm M12 BOLT = 40Nm |
LEGEND
| ITEM No. | DESCRIPTION | QTY |
| ITEM 1 | MAIN BRACKET | 1 |
| ITEM 2 | NUMBER PLATE LIGHT CONNECTOR | 1 |
| ITEM 3 | RUBBER BUNG | 1 |
| ITEM 4 | 20mm BUTTON HEAD BOLT | 2 |
| ITEM 5 | 25mm BUTTON HEAD BOLT | 2 |
| ITEM 6 | FLAT WASHER | 6 |
| ITEM 7 | NYLOC NUT | 2 |
| ITEM 8 | 75mm CABLE TIE – BLACK | 4 |
| ITEM 10 | 200mm LENGTH OF Ø18mm HEAT SHRINK | 1 |
| ITEM 11 | 200mm LENGTH OF HEAT SHRINK | 1 |
| ITEM 12 | LICENCE PLATE LIGHT (W/SHROUD) | 1 |
| ITEM 13 | 100mm LENGTH OF SELF-ADHESIVE FOAM | 1 |
ASSEMBLY DIAGRAM
FITTING INSTRUCTIONS
Disassembly of OEM Tail Unit:
- Disconnect the wiring connector going to the OEM number plate light unit located under the passenger seat.
- Remove the OEM tail unit via the four bolts on the tail unit/ undertray of the motorcycle.
- Once removed, unscrew all visible bolts on the OEM Tail Unit, disassemble the unit, then remove the OEM indicators for later use.
- Also, remove the sub-loom for use with the R&G tail tidy.
- Reassemble the OEM Tail unit without the indicators and store it safely.
Tail Tidy Assembly:
- Insert the supplied rubber bung into the 1” hole on the tail tidy bracket.
- If required cut the supplied self-adhesive foam strips to a similar size shown in the assembly diagram above and stick in the position shown.
- Fasten the supplied R&G number plate light to the tail tidy assembly.
- Bolt the OEM indicators onto the tail tidy, using the supplied nyloc nuts and washers with the OEM bolts.
- Use the larger diameter heat shrink supplied to cover the sub loom and the smaller heat shrink to cover the number plate light and indicator wiring, using electrical tape to seal/cover any gaps as required.
- Pass the wiring through the rubber bung, then cable tie the loom in place using the cable tie slots as shown in the second diagram.
- Offer up the tail tidy to the motorcycle and pass the connectors through the hole in the undertray.
- Then pass 2x of the supplied 25mm button head bolts (Item 6) with washers through the rearward holes in the main bracket then through the motorcycles undertray and hand tighten.
Please note: You mustn’t tighten the longer 25mm bolts into the mounting holes closest to the front of the bike, as this will damage the captive dome nuts on the inside of the tail unit. - Then pass the remaining 2x 20mm button head bolts (Item 4) through the forward mounting holes and hand tighten.
- Connect the indicator and number plate light connectors to the original sub-loom.
Test the indicators and number plate light function correctly before continuing with the fitting. - Then fully tighten the bolts to the required torque spec.
IMPORTANT: FOR SAFETY, ENSURE THE LICENCE PLATE IS PLACED AS HIGH AS POSSIBLE ON THE TAIL TIDY (IT MAY REQUIRE DRILLING). IF FITTING A LICENCE PLATE OF 200MM OR LONGER (INCLUDING ANY SHROUD OR REFLECTOR ATTACHMENT) TO THE BRACKET, BEFORE RIDING, FULLY COMPRESS THE SUSPENSION TO ENSURE NO PART OF THE ASSEMBLY CAN CONTACT THE TYRE WHILE THE VEHICLE IS IN MOTION OR UNDER LOAD. IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY OR DAMAGE TO THE MOTORCYCLE.
- ISSUE 1 30/05/2024 TB
- CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products, and R&G may make design changes which do not diminish their performance or visual appeal, and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation, and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services, it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products, R&G shall at its option either supply a replacement or refund the purchase money, but shall not be liable if the Products have been modified or used or maintained otherwise than by R&G’s orthe manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than as identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss, and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if pre-authorized, the return will be rejected). Goods may only be returned directly to us if they were purchased directly from us (the customer must prove this if necessary). Otherwise to be returned to the original vendor. Goods must be in resellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value, excluding P&P – at the prevailing price at time of purchase). The customer must pay carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
R&G
- Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
- Tel: +44 (0)1420 89007
- Fax: +44 (0)1420 87301
- www.rg-racing.com
- Email: info@rg-racing.com
FAQS
Q: Can I install this license plate bracket myself?
A: Yes, you can install it following the detailed fitting instructions provided in the manual. If unsure, consult a professional technician.
Q: Are all necessary parts included in the kit for installation?
A: Yes, ensure all parts listed in the manual are present before proceeding with installation.
Documents / Resources
 |
R and G LP0376BK Licence Plate Bracket [pdf] User Guide LP0376BK Licence Plate Bracket, LP0376BK, Licence Plate Bracket, Plate Bracket, Bracket |