QUIO QU-KD2N-HF Chip Card 
Reader User Guide
QUIO QU-KD2N-HF Chip Card Reader User Guide
Contents hide
1 Features & Specification
2 Wiring Diagram
3 Network Parameter Setting
4 Network Mode Switch
5 USB Connection
6 V8 Tools Tool Parameter Setting
7 Documents / Resources
7.1 References

Features & Specification

Feature:
  • Multi-mode access control
  • Support ISO15693 / ISO14443A (Mifare) / ISO14443B / DESFire / NTAG203
  • 2.42 inch OLED Display
  • Multi communication interface
  • Provide protocol to develop
Specification:
Title QUIO QU-KD2N-HF Chip Card Reader - Specification

Wiring Diagram

QUIO QU-KD2N-HF Chip Card Reader - Wiring Diagram

Network Parameter Setting

  1. Execute “NET_Discover_V0110.exe” and press Discover iconto search QUIO series product.
  2. Factory default IP is “192.168.1.101”. User can check the MAC address from product sticker with IP to confirm the device.
    QUIO QU-KD2N-HF Chip Card Reader - Network Parameter Setting
  3. Double click IP (192.168.1.101) to open the web configure page(http://192.168.1.101)
    Default login ID / Password : admin / admin
    QUIO QU-KD2N-HF Chip Card Reader - Double click IP (192.168.1.101) to open the web configure
  4. Default Net Mode is the same as the following. User can modify Net Mode and other parameters. If device cannot communicate properly after setting, user can reset NET module via Micro USB.
    QUIO QU-KD2N-HF Chip Card Reader - Default Net Mode is the same as the following

Network Mode Switch

QUIO device support 4 network modes: Default, ETH (Ethernet)、Wi-Fi(STA)
QUIO QU-KD2N-HF Chip Card Reader - Network Mode Switch
  1. ETH: Factory default is ETH-SERIAL. ( Standard TCP/IP Reader )
    QUIO QU-KD2N-HF Chip Card Reader - ETH Factory default is ETH-SERIAL
    When user modify the IP and click on Apply button, device will reboot and apply the setting after 30 seconds.
    QUIO QU-KD2N-HF Chip Card Reader - When user modify the IP and click on Apply button
  2. WIFI(STA)：QUIO can be set to communicate via Wireless AP without Ethernet.
    QUIO QU-KD2N-HF Chip Card Reader - WIFI(STA) QUIO can be set to communicate via Wireless AP without Ethernet

STA SSID: Enter the SSID from AP you will connect to network.
Scan icon : User can scan AP in range of device and select one to connect. But user cannot scan the
AP after changing default network mode (Ethernet only) to Wi-Fi (Client). Device need to power off /
on to enable the scan function.
STA Enc Type : Select Encrypt type for AP connection.
Password: Enter password for AP.
IP Type: DHCP is default mode. If user have to setup a static IP, please select Static.

PS: Wi-Fi MAC address is Ethernet MAC subtract 1.
Ex. Ethernet MAC : AC:A2:13:B5:5A:B5， Wi-Fi MAC : AC:A2:13:B5:5A:B4

3. Default mode：Ethernet (DHCP) +Wi-Fi AP mode.
It’s Dual-Mode ( Ethernet and Wi-Fi AP，but Ethernet only support DHCP.)

QUIO QU-KD2N-HF Chip Card Reader - Default mode Ethernet (DHCP) +Wi-Fi AP mode
QUIO QU-KD2N-HF Chip Card Reader - Default mode Ethernet (DHCP) +Wi-Fi AP mode
AP SSID: Setup device’s SSID.
AP Passwd: Device’s Wi-Fi password. (Default is 12345678)

USB Connection

Setup parameters via Micro USB.
QUIO QU-KD2N-HF Chip Card Reader - USB Connection
  1. Install USB driver ”CDC_USB_Driver_VCP_V1.4.0_Setup.exe”
  2. System will generate a virtual COM port.
For example. Check port in device manager.(below picture is COM 3)
QUIO QU-KD2N-HF Chip Card Reader - System will generate a virtual COM port
User also can update driver manually. The driver is saved in the folder that is same as following.
QUIO QU-KD2N-HF Chip Card Reader - User also can update driver manually
3. Get device Model information and serial number by using V8 Tools with correct COM port or Ethernet connection.
QUIO QU-KD2N-HF Chip Card Reader - Get device Model information and serial number by using V8

V8 Tools Tool Parameter Setting

1. Basic:
QUIO QU-KD2N-HF Chip Card Reader - Basic
Basic: Get device serial number、device ID and firmware version
Warm Start: Reboot device
Initial: Restore device to factory default (It is NOT including network setting).
NET Initial (6 sec): Restore network parameter of device to Default mode.
2. Reader
QUIO QU-KD2N-HF Chip Card Reader - Reader
Set Interface: Setup reader’s communication interface. Default is “RS485”.
Set Message Mode:
Card LED: Time for read card LED ON, default is 30 x 10ms
Card Beep: Time for read card beep on, default is 30 x 10ms
ISO14443A/B/ISO15693 :
Same Card Delay: Setup time gap for reading the same card, default is 10 x100ms (1 second)
Green Mode: Slow down the card read speed to power saving.
Reset: Reset RF IC after read card.
Card Type: Choose card type to enable device’s read specific card.
UID(A): Read ISO14443A Card UID.
Block: Read Block data (Must disable other card type).
UID(B): Read ISO14443B Card UID.
GUID(B): Read the China second generation of resident identification card.
ISO15693: Read ISO15693 Card UID
7 byte: Read 7byte format Card UID
Card Test: Test the reader function.
3. Display : Set up display language and encode for different country.
QUIO QU-KD2N-HF Chip Card Reader - Display Set up display language and encode for different country
Test send message command with tools.
QUIO QU-KD2N-HF Chip Card Reader - Test send message command with tools
Auto send reader mode
1.Un- Select “Controller Mode” and then click “Set DI/DO Mode” to disable controller mode.
QUIO QU-KD2N-HF Chip Card Reader - Un- Select Controller Mode and then click Set DI DO Mode to disable controller mode
2. Select “EN” (means enable), “S/N”, “CLR”, “CRC” and set heartbeat to 50 (means 5 sec) and then click “Auto Mode” to finish configure.
QUIO QU-KD2N-HF Chip Card Reader - Select EN (means enable), SN, CLR, CRC and set heartbeat to 50 (means 5 sec)

Documents / Resources

QUIO QU-KD2N-HF Chip Card Reader [pdf] User Guide
QU-KD2N-HF Chip Card Reader, QU-KD2N-HF, Chip Card Reader, Card Reader

References

Leave a comment

Your email address will not be published. Required fields are marked *