QUANTUM NETWORKS QN-SW225-24P Network Switch
Specifications:
- Brand: QNTMNET
- Product: Network Switch
- Supported Protocols: TFTP, SCP
- Maximum Defined DHCP Servers: 8
Product Usage Instructions
DHCP Relay Commands
ip dhcp relay enable (Global)
Syntax: ip dhcp relay enable | no ip dhcp relay enable
Default Configuration: DHCP relay feature is disabled.
Command Mode: Global configuration mode.
Usage: Use the ip dhcp relay enable Global Configuration mode command to enable the DHCP relay feature on the device. Use the no form of this command to disable the DHCP relay feature.
Example: switchxxxxxx(config)# ip dhcp relay enable
ip dhcp relay enable(Interface)
Syntax: ip dhcp relay enable | no ip dhcp relay enable
Default Configuration: Disabled.
Command Mode: Interface Configuration mode.
Usage: Use the ip dhcp relay enable Interface Configuration mode command to enable the DHCP relay feature on an interface. Use the no form of this command to disable the DHCP relay agent feature on an interface.
Example: switchxxxxxx(config)# interface vlan 21 switchxxxxxx(config-if)# ip dhcp relay enable
ip dhcp relay address (Global)
Syntax: ip dhcp relay address ip-address | no ip dhcp relay address [ip-address]
Default Configuration: No server is defined.
Command Mode: Global Configuration mode.
Usage: Use the ip dhcp relay address Global Configuration mode command to define the DHCP servers available for the DHCP relay. Use the no form of this command to remove the server from the list.
Example: switchxxxxxx(config)# ip dhcp relay address 176.16.1.1
ip dhcp relay address(Interface)
Syntax: ip dhcp relay address ip-address | no ip dhcp relay address [ip-address]
Default Configuration: No server is defined.
Command Mode: Interface Configuration mode.
Usage: Use the ip dhcp relay address Interface Configuration (VLAN, Ethernet,Port-channel) command to define the DHCP servers available by the DHCP relay for DHCP clients connected to the interface. Use the no form of this command to remove the server from the list.
PRODU CT OVERVIEW
- QN-SW-225 Switch Series provides robust Layer 2 switching and Layer 3 routing features to meet the diverse needs of enterprise/campus networks.
- On-device management ports include a dedicated console port, an Out of Band management port, and a USB flash drive port for storage.
- Centralized device management options -Cloud hosted Quantum Rudder Network and Services Controller (NSC), on premises Rudder NSC, Device GUI/CLI, SNMP.
- PoE budget options to power advanced devices with the option of PoE / PoE+ / PoE++ (60W/90W) per port.
- This switch provides a flexible range of downlink ports, from 8 to 48, to accommodate your network needs. It also offers 2 or 4 SFP+ uplink ports for high-speed connections.
- Three-year limited liability manufacturer’s warranty from day one.
HIGHLIGHTS
- Simplified network management.
Unified management stacks (Rudder, Network and Service Controller) to deploy, monitor, and troubleshoot wired as well as wireless networks. - Centralized network observability.
Dashboards and reporting logs for various network events. - Reliable performance.
Delivers Stability, Scalability, and Effortless handling of diverse workloads.- The switch supports a non-blocking architecture that provides from 56 Gbps to 176 Gbps of wire-speed switching capacity and from 42 to 131 Mpps of forwarding capacity, allowing it to handle a wide range of workloads.
- For better network security, the switch supports multiple authentication methods, including 802.1x and MAC authentication. The switch provides identity-driven security and controls via granular Access Control Lists (ACLs).
KEY SPECIFICATION
QN-SW-225-Series
| Communication Ports | Specifications | ||||||||||
| Models | 10/100/1000
Mbps RJ45 Downlinks |
1G Fiber Downlinks | 10G Fiber Uplinks | 1G Fiber Uplinks*1 | PoE Budget*2 (Watt) | Max PoE (802.3af) | Max PoE+ (802.3at) | Max PoE++ (802.3bt) | |||
| 48 Ports | |||||||||||
| QN-SW-225-48P | 48 | – | 4 | 740 | 48 | 24 | – | ||||
| QN-SW-225-48 | 48 | – | 4 | – | – | – | – | ||||
| 24 Ports | |||||||||||
| QN-SW-225-24FP | 24 | – | 4 | 740 | 24 | 24 | – | ||||
| QN-SW-225-24P | 24 | – | 4 | 400 | 24 | 12 | – | ||||
| QN-SW-225-24 | 24 | – | 4 | – | – | – | – | ||||
| 16 Ports | |||||||||||
| QN-SW-225-16P-2SFPP | 16 | – | 2 | 240 | 16 | 8 | – | ||||
| QN-SW-225-16 | 16 | – | 4 | – | – | – | – | ||||
| 12 Ports | |||||||||||
| QN-SW-225-12P-2SFPP | 12 | – | 2 | 188 | 12 | 6 | – | ||||
| QN-SW-225-12 | 12 | – | 2 | – | – | – | – | ||||
| 8 Ports | |||||||||||
| QN-SW-225-8FPU | 8 | – | 2 | 240 | 8 | 8 | 2 | ||||
| QN-SW-225-8FP | 8 | – | 2 | 240 | 8 | 8 | – | ||||
| QN-SW-225-8P | 8 | – | 2 | 120 | 8 | 4 | – | ||||
| QN-SW-225-8F | – | 8 | 2 | – | – | – | – | ||||
| QN-SW-225-8 | 8 | – | 2 | – | – | – | – | ||||
| QN-SW-225-8-4SFP | 8 | – | – | 4 | – | – | – | – | |||
| Management Ports | 48 Ports | 24 Ports | 16 Ports | 12 Ports | 8 Ports | ||||||
| Console (RJ45) | 1 | 1 | 1 | 1 | 1 | ||||||
| Management (OOB) | 1 | 1 | 1 | 1 | 1 | ||||||
| Storage (USB Type A) | 1 | 1 | 1 | 1 | 1 | ||||||
| Capacity | 48 Ports | 24 Ports | 16 Ports | 12 Ports | 8 Ports | ||||||
| Switching capacity | 176 Gbps | 128 Gbps | 112 Gbps | 64 Gbps | 56 Gbps | ||||||
| Forwarding rate | 131 Mpps | 95 Mpps | 84 Mpps | 48 Mpps | 42 Mpps | ||||||
| MAC address table | Max 16K | Max 16K | Max 16K | Max 16K | Max 16k | ||||||
| Active VLANs support | 4096 | 4096 | 4096 | 4096 | 4096 | ||||||
| Active VLANs support | 4096 | 4096 | 4096 | 4096 | 4096 | ||||||
| IPv4 Route | 480 | 480 | 480 | 480 | 480 | ||||||
| IPv6 Route | 120 | 120 | 120 | 120 | 120 | ||||||
- The switch model with a 1G SFP uplink port does not support the stacking feature.
- The PoE power budget will be -30 or +30 watts, depending on the current power budget.
| Quality of Service | |
| DiffServ (Differentiated services) | Strict priority support |
| Priority queue | Traffic shaping/policing |
| ACL mapping to priority queue | WRR support |
| Flow mirror, 802.1p Support | SP+WRR |
| Flow redirection | Rate limiting (Based on per port and per queue) |
| Single Rate Three Color Marker (srTCM) | Class map defines traffic flow with ACLs or support for
network traffic management |
| Two Rate Three Color Marker (trTCM) | Policy map & route MAP to define the action for a set of
classified inbound traffic |
| QoS based on classification (Based on IP, MAC and VLAN) | |
| Security | |
| RADIUS, TACACS+ | Downloadable ACL |
| Port security | Dynamic ACL |
| DHCP Snooping | Role based access control |
| AAA (Authentication, Authorization, and Accounting) | 802.1x authentication (Port Based, MAC Based, Web
Based) |
| ACL (Based On IP, Port, Protocol, MAC, Time Based) | Management ACL |
| IP source guard | DoS prevention |
| Protected port | Secure copy (SCP) |
| ARP inspection (DAI & SAI) | Kerberos |
| SSL | |
| Multicast | |
| Internet Group Management Protocol -IGMP v1/v2/v3 | Multicast Listener Discovery- MLD v1/V2 |
| IGMP snooping | MLD snooping |
| PIM-SM/SSM | Multicast TV VLAN |
| PIM-SMv6 | MVR (Multicast VLAN registration) |
| Layer 3 | |
| IPv4 and IPv6 dual stack | IPv6 prefix list |
| Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) | IP source guard |
| Policy Based Routing (PBR) | DHCP server |
| ARP, Gratuitous ARP | DHCP relay |
| DHCP Client | IPv6 NDRA (Neighbor Discovery Router Advertisement) |
| ICMP redirect & ICMP unreachable | Duplicate Address Detection (DAD) |
| IPv6 SLAAC (Stateless Address Auto configuration) | IPv6 ND |
| ARP-Proxy | DHCP Option 82, 66, 67 |
| Layer 3 Routing | |
| Static routing (IPv4, IPv6) | Inter-VLAN routing |
| Routing Information Protocol, version 2 (RIPv2) | OSPFv2/v3 (Open Shortest Path First) |
| Layer 2 | |
| Port Tagging/untagged | BPDU guard |
| MAC based VLANs | GVRP |
| Private VLAN | LLDP/LLDP MED |
| Subnet based VLAN | RADIUS assigned VLAN |
| Auto MDI/MDIX | Link aggregation (Ether Channel) |
| Loopback detection | Link Aggregation Control Protocol (LACP) |
| Port isolation | Port mirroring (Port, ACL, VLAN Based) |
| Root guard | Default VLAN |
| Guest VLAN | Auto voice VLAN |
| Energy Efficient Ethernet (EEE) | Green Ethernet |
| Link flapping detection | Flow control |
| STP/RSTP/MSTP | Native VLAN |
| QinQ (802.1Q) | Loop guard |
| High Availability | |
| Stacking (Up-to 8 members) | Ring Redundancy Protocol (RRP) |
| Equal-Cost Multi Path (ECMP) | Virtual Router Redundancy Protocol (VRRP) |
| Storm control (Broadcast, Multicast, Unicast) | |
| Management | |
| Local GUI | Management: RUDDER (Controller)/Standalone |
| Industrial standard CLI | SPAN/RSPAN |
| Telnet support | SSHv1/v2 |
| Storage & File management with USB | Firmware auto install support |
| TFTP support | Syslog server |
| SNMP v1/v2c/v3 | RMON (All 4 Groups 1,2,3,9) |
| Standard Compliance | |
| IEEE Standards Compliance | |
| 802.1AB LLDP/ LLDP-MED | 802.3ae 10 gigabit Ethernet |
| 802.1D MAC bridging | 802.3at power over Ethernet Plus |
| 802.1p Mapping to priority queue | 802.3u 100Base-TX |
| 802.1s Multiple Spanning Tree (MST) | 802.3x flow control |
| 802.1w Rapid Reconfiguration of Spanning Tree (RSTP) | 802.3z 1000Base-SX/LX |
| 802.1x Port-based Network Access Control (PNAC) | 802.3 MAU MIB (RFC 2239) |
| 802.3 Carrier Sense Multiple Access/Collision Detection
(CSMA/CD) |
802.1Q VLAN tagging |
| 802.3ab 1000Base-T | 802.3az Energy Efficient Ethernet |
| 802.3 10Base-T | 802.3af Power over Ethernet |
| 802.3ad link aggregation (Dynamic and Static) | |
| Monitoring and Troubleshooting | |||||
| Errdisable detection and recovery | CPU Utilization | ||||
| Device temp/PSU/FAN/status display & alarm | User operation logs | ||||
| Virtual cable test | Management logs, alarms | ||||
| ICMPv4/v6 | DDM (Digital Diagnostic Monitoring) | ||||
| Traceroute | UDLD (Unidirectional Link Detection) | ||||
| Physical | |||||
| Model | Net Weight | Dimensions (H x W x D) | Fan | MTBF | |
| QN-SW-225-48P | 4.46 KG | 44 x 440 x 300mm | Yes | 1,00,000 hrs | |
| QN-SW-225-48 | 3.52 KG | 44 x 440 x 300mm | Yes | 1,00,000 hrs | |
| QN-SW-225-24FP | 3.72 KG | 44 x 440 x 350mm | Yes | 1,00,000 hrs | |
| QN-SW-225-24P | 3.56 KG | 44 x 440 x 350mm | Yes | 1,00,000 hrs | |
| QN-SW-225-24 | 2.81 KG | 44 x 440 x 245mm | No | 1,00,000 hrs | |
| QN-SW-225-16P-2SFPP | 3.42 KG | 44 x 440 x 250mm | Yes | 1,00,000 hrs | |
| QN-SW-225-16 | 2.62 KG | 44 x 440 x 245mm | No | 1,00,000 hrs | |
| QN-SW-225-8FPU | 1.48 KG | 44x 210 x 210 mm | No | 1,00,000 hrs | |
| QN-SW-225-8FP | 1.48 KG | 44x 210 x 210 mm | No | 1,00,000 hrs | |
| QN-SW-225-8P | 1.38 KG | 44x 210 x 210 mm | No | 1,00,000 hrs | |
| QN-SW-225-8F | 1.38 KG | 44x 210 x 210 mm | No | 1,00,000 hrs | |
| QN-SW-225-8 | 1.09 KG | 44x 210 x 210 mm | No | 1,00,000 hrs | |
| QN-SW-225-8-4SFP | 1.38 KG | 44x 210 x 210 mm | No | 1,00,000 hrs | |
| Environment | |||||
| Operating temperature | -5°C (23°F) to 65°C (149°F) | ||||
| Humidity | 5% ~ 95% non-condensing | ||||
| RoHS | Compliant | ||||
| Voltage input | 100-240V. Frequency: 50/60Hz | ||||
| Power consumption | Internal PSU ≤40W, External PSU ≤100W | ||||
| Packaging Content | |||||
| Switch with type D power cord with rack mounting kit | |||||
CERTIFICATION & COMPLIANCES*3
| Regulatory | FCC |
| BIS | |
| TEC | |
| Environmental | RoHS |
| CE |
For more information, visit www.qntmnet.com/certification or email us at sales@qntmnet.com.
ORDERING INFORMATION
| Part Number | Description |
| QN-SW-225-48P | Networking Switch,48×10/100/1000 Base-T ports with 4x10G Fiber uplinks,740 Watts PoE
Budget, Includes 3-year online activation warranty. |
| QN-SW-225-48 | Networking Switch, 48×10/100/1000 Base-T ports with 4x10G Fiber uplinks, Includes 3-
year online activation warranty. |
| QN-SW-225-24FP | Networking Switch, 24×10/100/1000 Base-T ports with 4x10G Fiber uplinks, 740 Watts
PoE Budget Includes 3-year online activation warranty. |
| QN-SW-225-24P | Networking Switch, 24×10/100/1000 Base-T ports with 4x10G Fiber uplinks, 400 Watts
PoE Budget Includes 3-year online activation warranty. |
| QN-SW-225-24 | Networking Switch, 24×10/100/1000 Base-T ports with 4x10G Fiber uplinks, Includes 3-
year online activation warranty. |
| QN-SW-225-16P-2SFPP | Networking Switch, 16×10/100/1000 Base-T ports with 2x10G Fiber uplinks,240 Watts PoE
Budget, Includes 3-year online activation warranty. |
| QN-SW-225-16 | Networking Switch, 16×10/100/1000 Base-T ports with 4x10G Fiber uplinks, Includes 3-year
online activation warranty. |
| QN-SW-225-12P | Networking Switch, 12×10/100/1000 Base-T ports with 2x10G Fiber uplinks,188 Watts PoE
Budget, Includes 3-year online activation warranty. |
| QN-SW-225-12 | Networking Switch, 12×10/100/1000 Base-T ports with 2x10G Fiber uplinks, Includes 3-year
online activation warranty. |
| QN-SW-225-8FPU | Networking Switch, 8×10/100/1000 Base-T ports with 2x10G Fiber uplinks,1-2 Port Support
PoE++ (60W) Support, 240 Watts PoE Budget. Includes 3-year online activation warranty. |
| QN-SW-225-8FP | Networking Switch, 8×10/100/1000 Base-T ports with 2x10G Fiber uplinks,240 Watts PoE
Budget, Includes 3-year online activation warranty. |
| QN-SW-225-8P | Networking Switch, 8×10/100/1000 Base-T ports with 2x10G Fiber uplinks,120 Watts PoE Budget, Includes 3-year online activation warranty. |
| QN-SW-225-8F | Networking Switch, 8×10/100/1000 1G SFP ports with 2x10G Fiber uplinks, Includes 3-year online activation warranty. |
| QN-SW-225-8 | Networking Switch, 8×10/100/1000 Base-T ports with 2x10G Fiber uplinks, Includes 3-year online activation warranty. |
| QN-SW-225-8-4SFP | Networking Switch, 8×10/100/1000 Base-T ports with 4x1G Fiber uplinks, Includes 3-year online activation warranty. |
For more information, visit system upgrade reference details.
Frequently Asked Questions
Q: How many DHCP servers can be defined globally?
A: Up to 8 DHCP servers can be defined globally using the ip dhcp relay address command in Global Configuration mode.
Q: What is the default configuration for the DHCP relay feature?
A: The default configuration is that the DHCP relay feature is disabled.
Documents / Resources
 |
QUANTUM NETWORKS QN-SW225-24P Network Switch [pdf] User Guide QN-SW225-24P Network Switch, QN-SW225-24P, Network Switch, Switch |