S7300-48TE4X2QQuickStartGuide
Quick Start Guide
V2.0
S7300-48TE4X2Q 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch
48-Port Multi-Gigabit Ethernet L3 Switch
48x 100M/1000M/2.5GBASE-T Ports, with 4x 1G/10G SFP+and 2x 40G QSFP+ Uplinks, Support BGP
Introduction
The QSFPTEK S7300-48TE4X2Q multi-gigabit L3 switch has 48x 100M/1000M/2.5GBASE-T RJ45 ports and 4x 10G and 2x 40G uplinks. S7300-48TE4X2Q is an access layer switch for high-end campuses, enterprise branches and SMB networks. With high- density 2.5G Ethernet ports for directly connecting gaming computers, S7300-48TE4X2Q is popular for deployment in the e-sports industry, such as high-end Internet cybercafes, gaming hotels, E-sports arenas, etc.
We appreciate your decision to select S7300-48TE4X2Q. This manual is intended to help you become acquainted with the switch design and provide instructions for implementing the switches into your network. 
Accessories
Hardware Overview
Front Panel Ports 
| Ports | Description |
| RJ45 | 100M/1000M/2.5G-T ports for Ethernet connection, with LINK/ACT indicators |
| SFP+ | Hot-swappable SFP+ ports for 1/10G connection, with LINK/ACT indicators |
| QSFP+ | Hot-swappable SFP+ ports for 1/10G connection, with LINK/ACT indicators |
| CON | An RJ45 console port for serial management |
| ETH | An RJ-45 Ethernet management port |
Front Panel LEDs 
| LEDS | Status | Description | |
| RJ45 (Port 1-48) | Green | On | 2.5G port link. |
| Blinking | 2.5G packets receiving or transmitting. | ||
| SFP+ (Port TE1-TE4) | Green | On | 10G port link. |
| Blinking | 10G packets receiving or transmitting. | ||
| QSFP+ (Breakout) | Green | On | 10/40G port link. |
| Blinking | 10/40G packets receiving or transmitting. | ||
| SYS LED | / | / | If the SYS indicator flickers, the system works normally. |
| PWR LED | / | / | If the PWR indicator is always on, the device is powered on. |
Back Panel 
Installation Requirements
Tools Preparation
- Screwdriver
- Static-proof wristband
- Bolt
- Ethernet cable
- Other Ethernet terminal devices
- Control terminal
Safety Principles
Keep dustless and clean during or after the installation.
- Put the cover in a safe place.
- Put tools in the right place where they are not easily falling down.
- Put on relatively tight clothes, fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.
- Put on protective glasses if the environment may cause damage to your eyes.
- Avoid incorrect operations that may cause damage to humans or devices.
Site Environment
- Make sure that the workshop is well-ventilated, the heat of electrical devices is well- discharged
- Avoid damaging devices by following the electrostatic discharge prevention procedure.
- S7300-48 TE4X2Q Hardware Installation Manual
- Put the machine box in a place where cool air can blow off the heat inside the machine box.
- Make sure the machine box is sealed.
Mounting the Switch
Connecting the Power 
- Plug the AC power cord to the switch power port on the back rear.
- Connect the other end of the power cord to an AC power source equipment.
Connecting the RJ45 Ports 
- Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.
- Connect the other end of the Ethernet cable to the switch RJ45 port.
Connecting the SFP+ Port 
- Insert the SFP+ module into the SFP+ port.
- Plug a fiber patch cable into the SFP+ transceiver.
- Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the QSFP+ Port 
- Insert the QSFP+ module into the QSFP+ port.
- Plug a fiber patch cable to the QSFP+ transceiver.
- Connect the other end of the fiber to the device that you want to realize data communication.
Connecting the Management Ports
Connecting the Console Port
- Prepare a console cable.
- Insert the RJ45 connector of the console cable into the console port on the switch.
- Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.
Configuring the Switch
Configuring the Switch Using the Web-based Interface
Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser. 
Step 2: Set the IP address of the computer to 192.168.0.x (where “x” is any number from 2 to 254) and the subnet mask to 255.255.255.0.
Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin).
Step 4: Click sign-in to access the web-based configuration page.
Configuring the Switch Using the Console Port
Step 1: Use the console cable to directly connect the switch console port to your computer.
Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.
Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control. 
Step 4: Enter the default username and password (admin/admin).
Troubleshooting
Hardware Fault Analysis
- Power and cooling systems—power and fan
- Port, cable and connection—ports on the front panel of the switch and the cables connecting these ports
Faults Relative to Power and Cooling System
Do the following checkups to help remove the fault:
- When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.
- If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 “Requirements for Common Locations”.
- If the switch cannot be started and the PWR indicator is off, check the power.
Faults Relative to Port, Cable and Connection
Do the following checkups to help remove the fault:
- If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.
- If the power on-off is at the “ON” location, check the power source and the power cable.
- If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control.
Support and Other Resources
- Contactus https://www.gsfptek.com/company/contact-us.html
- Customer Success https://www.gsfptek.com/resources/customer-success-stories
- Email support@gsfptek.com
Product Warranty
S7300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. You are eligible to apply for a return within 14 days and exchange within 90 days of receiving them.
For more details about applying qualifications, please live chat or email sales@qsfptek.com for support.
5 Year Warranty
14-day Return Windowwww.qgsfptek.com
V2.0
Documents / Resources
 |
QSFPTEK S7300-48TE4X2Q 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch [pdf] User Guide S7300-48TE4X2Q 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch, S7300-48TE4X2Q, 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch, Managed Stackable Ethernet L3 Switch, Stackable Ethernet L3 Switch, Ethernet L3 Switch, L3 Switch |
 |
QSFPTEK S7300-48TE4X2Q 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch [pdf] User Guide S7300-48TE4X2Q 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch, S7300-48TE4X2Q, 48 Port Multi Gigabit Managed Stackable Ethernet L3 Switch, Multi Gigabit Managed Stackable Ethernet L3 Switch, Managed Stackable Ethernet L3 Switch, Stackable Ethernet L3 Switch, Ethernet L3 Switch, L3 Switch |
