Q-TRAN AK1RGB Linear Fixtures Surface Owner's Manual

Attach the provided stainless steel plastic clips to the desired surface. For fixtures that are 4′ or less, use 2 clips. For fixtures that are greater than 4′, use 4 clips. If additional clips are needed, you can order them separately using SST-03.

Step 2: Wiring

Connect the wires to the fixture using the following instructions:

Wire Input:

The standard wire input is bare wire (standard 24). Connect the white wire to the positive terminal and the black wire to the negative terminal.

Wire Output:

The standard wire output is closed end (no feed). Connect the white wire to the positive terminal and the black wire to the negative terminal.

Note:

If you need a custom wire length, you can request it by writing the desired length next to “BW” in the part number. For example, if you need a 48-inch wire, write “BW48” in the part number.

Step 3: Power Supply

Refer to the last page of the manual for compatible power supplies. Make sure to use a Q-Tran power supply for the 5-year warranty to be valid.

Step 4: Diode Visibility and Photometric Performance

For representation of LED visibility and beam angles, refer to the Diode Visibility and Photometric Performance sections on the following pages.

FAQ

Q: What is the warranty for this product?

A: The product comes with a 5-year warranty. Please note that the warranty is only valid when used with Q-Tran power supplies.

Q: Can I make modifications to the product in the field?

A: No, field modifications will void the warranty. Please consult a professional if any modifications are required.

Q: Are there any temperature ratings for this product?

A: The temperature ratings are not specified in the user manual. Please refer to the specifications section for more detailed information.

Q: What are the configuration options for wire input/output?

A: The standard configuration is bare wire (BW) for wire input and closed end (CLS) for wire output. No further specifications are needed for these options.

Q: What wire colors are available?

A: The available wire colors are white and black. Please select the appropriate wire color based on your preference or installation requirements.

ARKA-FLAT (01) RGB

Linear Fixtures – Corner & Surface

Produces a wide 130º beam angle perfect for corner mount installations
Ideal for cove, under cabinet and millwork applications

Sample Part Number: AK1RGB-6.0-RGB-DRY-STD-DF-P1-BW-BW-BK-CL2-SST-BK-48″-E

Overview

PRODUCT – DIMENSIONS

DELIVERED LUMENS

DIODE VISIBILITY

PHOTOMETRIC PERFORMANCE

Nominal beam spread shown, beam spread varies based on light engine. For more detailed information, see photometric data.

TEMPERATURE RATINGS

WIRE INPUT/OUTPUT

CONFIGURATION OPTIONS

CONNECTOR/WIRE – IN/OUT

Connector/Wire In or Out not needed to specify product. Standard configuration is BW for Wire In and CLS for Wire out

WIRE COLOR

MOUNTING

SST

2 clips provided for 4′ or less; 4 clips provided for greater than 4′ To order separately use SST-03 Each clip comes with a #4 x 5/8″ Flat Head SS

2 clips provided for 4′ or less; 4 clips provided for greater than 4′ To order separately use PLC-02 Each clip comes with a #4 x 5/8″ Flat Head SS

EXACT/OPTIMAL FIXTURE LENGTH

EXAMPLES OF 12″ OPTIMIZED STATIC WHITE FIXTURES WITH DIFFUSED LENS

RGB DRY, DMP LENGTHS BY INCH

Exact fixtures are the length specified. Optimal fixtures’ length is rounded down with illumination end to end. All fixtures’ tolerance is +0 – 1/8”. Consult factory for lengths under 12″.

ЕХАСТ LENGTH

OPTIMAL LENGTH: highlighted rows are closest to requested nominal length

RGB WET LENGTHS BY INCH

Exact fixtures are the length specified. Optimal fixtures’ length is rounded down with illumination end to end. All fixtures’ tolerance is +0 – 1/8”. Consult factory for lengths under 12″.

EXACT LENGTH