PyleHome PDPC6T In-Ceiling Flush Mount Enclosure Speaker System
About Pyle Series CEILING SPEAKER
Congratulations! You have purchased one of our high-quality Pyle speakers. After numerous testing and investigations by our professional engineers, Pyle Series SPEAKER not only is in unique design but also could deliver consistent and high performance. PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE Thank you for choosing Pyle Audio’s In-Wall / In-Ceiling Enclosed Speaker.
INSTALLATION
Easy 4-Step Installation
- Cut a hole in your desired location. The hole should be 8” in diameter in order to fit the speaker. Make sure the length of your speaker wire is sufficiently long enough.
- Attach the speaker wire to the back of the speaker (see the below diagram).
- Place the speaker inside the hole you cut.
- Tighten the screws to secure your speaker in place.
Make sure to check the wattage and amperage of your speaker system while installing this speaker. The volt transformer should match the settings/specifications of your speaker system. The wattage setting will depend on the total watts your system can take and how many speakers you are going to use.
Features
The General Features of Pyle Series SPEAKER Include:
PDPC6T
- 6.5″LONG THROW WOOFER
- 10″ High-Temperature voice coil
- 1.0 “Mylar dome tweeter
- 250 watts rated peak power
- FREQUENCY RESPONSE:60Hz-20kHz
- 8 Ohm impedance
- 70v Transformer Trapping at : 8Ohm, 0.25w, 0.5W ,1W, 2.5W ,5W, 7.5W ,15W 30W
- Vented design for high power and deep bass response
- cut-out Dimension:112/25″(Diameter)518/25″(Depth)
We do confidence that Pyle Series SPEAKER will bring you many hours of enjoyment over the years.
SPECIFICATION
- MODEL NO: PDPC6T
- WOOFER: l x6.S”
- IMPEDANCE:8OHM
- VOICE COIL:1.0
- RESPONSE :60-20K HZ
- SPL(D8) 89
- PEAK POWER:250WATTS
PYLE cont really strives to improve the performance and value of its products-AU specif cations are subject to change.
Warranty and Support
You can get in touch with the manufacturer directly or find out more information on their website if you’d want a copy of the warranty for a product you saw on Amazon.com. Manufacturers’ warranties might not always be applicable, depending on things like how the product is used, where it was bought, and who sold it to you. If you have any issues, please read the guarantee, and then get in touch with the seller.
Frequently Asked Questions
No. The LED lights cannot be dimmed; they can only be switched on or off.
Actually, it consists of two separate parts that are joined by a few screws. Like any other completed conventional speaker, the speaker, which screws onto the back of the lights, has its own set of cords and terminals for making music. The front part of the light’s LEDs are powered by two cords.
No, ceiling speakers typically operate as passive speakers, which means that, because they lack built-in amplifiers, they are powered by speaker wires connected to an external amplifier. Each ceiling speaker is connected to the amplifier using the binding posts.
The receiver’s connection to ceiling speakers increases the possibility that there won’t be any further disconnections. You won’t have any trouble listening to quality music for a very long time if your speakers are correctly wired.
The greatest in-ceiling speakers give a bigger average listening area that is suitable for background music, despite the fact that they are directional and still require careful placement for the optimum audio picture. Even if you are at the room’s edges or corners, you can still receive a strong signal.
An external amplifier must be connected via speaker cable to each of the ceiling speakers in order to power them all. The Sonos Amp is, in our opinion, the greatest multi-room alternative.
Every TV will be equipped with an audio output. It will most likely be a digital optical output for the time being. You can listen to TV sound through your ceiling speaker system by running an analogue cable from your TV to the amplifier and switching to line output on your TV.
Create a passageway for the wires to pass through. Shut off the breaker after making sure the amplifier is unplugged. Connect the wiring. Start attaching the wires to the speaker terminals in the ceiling. Connect the other end of the wires to the amplifier’s terminals. Try it out by turning on your breaker.
Purchase a multi-zone AV receiver, then connect speaker wires to each amp-powered speaker. Your home audio system will be easier to set up if you choose an AV receiver with Bluetooth and Wi-Fi built in.
It is not resistant to moisture.
I’m sorry, but you are unable to turn the lights down. Please visit our website at pyleaudio.com for more information. In the search box, type the model number. I’m grateful.
Ceiling speakers can be used to play TV audio, however, they cannot be connected to TVs because they lack independent speaker outputs.
The distance between in-wall and ceiling speakers must be at least 18 to 24 inches.
