Pyle PDIW52 In-Wall / In-Ceiling Dual 5.25'' Speaker System-Complete Features User Manual

The Pyle PDIW speaker system clears up floor space while delivering stereo sound to every area in your house or place of business. These two 5.25-inch speakers attach flush for a tidy appearance, making them suitable for in-wall and in-ceiling settings.

The PDIW series speakers are ideal for custom installations and have a directional tweeter, exceptional power handling capacity, high-temperature voice coils, and high-efficiency response rates to provide a more rich and full-bodied sound. Speaker wire connections can be made easily and quickly with the help of convenient speaker connectors.

For simple installation, the system comes with a cut-out template. With the PDIW Speaker Systems, you may add audio and achieve wide-ranging sound performance in any environment.

What’s In the box

Speaker Placement

Installation process

The in-wall speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers, please contact your dealer or a qualified installer

Tools Needed

Trouble Shooting

IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:

Check that the receiver amplifier is on and a source is playing.
Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make Sure none of the speaker wires are frayed, cut, punctured or touching each other. Review the proper operation of your receiver/amplifier.

IF THERE Is NO SOUND COMING FROM ONE SPEAKER

Check the “Balance” control on your receiver amplifier.

Check wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.

IF THERE IS LOW (OR NO) BASS OUTPUT

Make sure the connections to the left and right “Speaker Inputs” have the correct polarity (+ and-)
Consider adding a powered subwoofer to your system.

In Dolby Digital or DIS modes, make Sure your receiver/ processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/ processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as LARGE “See your receiver/processors owner’s manual for further information on correct speaker configuration in Dolby Digital, DTS and other surround sound modes.

IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED

Check all wires and connections between the receiver/amplifier and speakers. Make sure all wires are connected. Make Sure none of the speaker wires are frayed, cut, punctured or touching each other more than one pair of main speakers is being used. check the minimum-impedance requirements of your receiver/amplifier

Wiring Diagram

Speaker connection

The wires for both speakers should be the same length. If one speaker is placed closer to the amplifier than the other, hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and (-) terminals. We use red to denote the () terminal and black for the (-) terminal. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and-on the speaker to (-) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and a poor stereo image. With the advent of multi-channel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material.

Existing connection

Cut the drywall. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.
Screw out the two screws to separate the frame first.
Place the frame assembly in the wall.
Screw down each of the six Philip screws. The locking tab will swivel into place and secure the unit to the rear surface of the drywall.
Connect the speaker wires to the speaker. Screw down of the six Phillips head screws.

Put in the strips of adhesive to secure the grille
Place the metal grille.
After installing the speaker grille gently press on the mesh pf the tweeter to adjust the position of the tweeter.

Frequently Asked Questions

Does Pyle make quality speakers?
This portable Bluetooth speaker sounds good and is a great value for the money. It has an easier time producing a respectable sound quality and a lot of volumes because it is a little bigger than many of the typical portable speakers available
Do ceiling speakers require a Sonos Amp?
No, your current setup does not require an amp. Just if you want to expand your Sonos ecosystem to include ceiling speakers.
Do my ceiling speakers require a subwoofer?
Even if ceiling speakers are capable of producing all the bass and low-end frequencies, a subwoofer will be helpful in handling them. Additionally, it considerably improves the overall quality of your sound system.
Are ceiling speakers for surround sound possible?
If the amplifier you’re using supports surrounds sound, then the answer is definitely. Up to five ceiling speakers would be hooked back to an AVR in a standard setup, however, this setup is cumbersome, necessitates several cords, and doesn’t offer the user a fantastic experience.
Do ceiling speakers raise the value of a house?
Even if you don’t have any immediate plans to move or sell, a built-in audio system will increase the value of your home if you ever decide to list it for sale. Customers will think they are getting a bonus if there are stylish in-wall or in-ceiling speakers.

View Fullscreen

References

User Manual

Pyle PDIW52 In-Wall / In-Ceiling Dual 5.25” Speaker System

Specifications

Introduction