Pyle PCA2 Power Amplifier System
Introductions
- Your New Pyle Pro Amplifier gives you the power and versatility you need in a professional sound system.
- The amplifier’s wide frequency response makes it suitable for amplifying music or vocal program material.
- PCA2 can compatible with Walkman and computerize devices (MP3) via 3.5mm to RCA converter.
- Please read this manual thoroughly before you attempt to set up and use the amplifier. It contains a range of installation suggestions as well as instructions to ensure safe usage.
- Installed properly, you can expect years of trouble-free service from this product.
CAUTION
- RISK OF ELECTRIC SHOCK DON’T OPEN
Warning
- To reduce the risk of fire or shock hazard, don’t expose this product to rain or moisture
- The lightning symbol is intended to alert you to the presence of uninsulated, dangerous voltage within this products enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the products case.
- The exclamation symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product.
Features and controls
- Power ON LED Indicator Lights to indicate power is turned on.
- Treble Tone Control Let’s you boost or attenuate treble, for the desired sound.
- Bass Tone Control Let’s you boost or attenuate bass, for the desired sound.
- Master Volume Control Let’s you adjust the overall sound level.
- RCA UR LINE Input Let’s you to connect the desired LINE input source.
- PUSH TYPE SPEAKER UR TERMINALS Let’s you easily connect speaker wires directly to the Amplifier.
- Voltage Selector Let’s you select the voltage of AC power input source. The amplifier has selectable input voltage from 11 OV/60Hz which is the standard in USA and CANADA. You can also switch the input voltage to 230V/50Hz for EUROPEAN operation. Please make sure the switch is in the proper position before operating, otherwise severe damage will result not cover by the warrnaty. Please also replace the fuse with proper rating in this situation (see the next instruction for the fuse rating).\
- Fuse The amplifier uses a fuse for protection against surges and short circuit. If the amplifier suddenly turns off and will not turn on, check the fuse, If necessary, replace it with a 1-amp, 250-volt, fast-acting, 5 x 20mm fuse (not supplied).
CARING FOR YOUR PYLE PRO AMPLIFIER
Your Pyle Pro Amplifier is an example of superior design and craftsmanship. The following suggestions will help you care for your amplifier so you can enjoy years of use:
- Keep the amplifier dry. If it gets wet, wipe immediately.
- Use the amplifier only in well-ventilated installations.
- Handle the amplifier away from dust and dirt.
- Wipe occasionally with a damp cloth to keep it looking new.
Do not use harsh chemical, solvents or detergents!
IMPORTANT
Replacing a fuse This amplifier requires a fuse with the proper rating for protection from power surges and short circuits. If the amplifier suddenly turns off or will not turn on. The fuse is properly blown.
- Let the amplifier cool down and see if it start again before you assume a fuse needs to be replaced.
- Unplug the amplifier from the AC outlet.
- Turn the fuse holder cap and pull out the cap.
- Remove the old fuse and replace it with an identical one.
CAUTION: Never use a fuse with a higher rating.
Connecting two 4-8 ohm speakers in stereo mode
TROUBLESHOOTING
- No power: The fuse might be blown. Check the amplifier’s fuse and replace it if necessary.
- No sound: Check all connections. Sound source or speakers not connected properly.
MASTER volume control set
- Adjust the volume control to desired setting. To minimum.
- The speaker’s wire might be
- Make sure all connected the wrong impedance. Speakers have the same impedance rating.
- The amplifier might has
- Turn the amplifier off and shut down. Let it cool. Make sure the amplifier is ventilated, and then turn it properly back on.
Limited warranty
All PYLE PRO products are carefully constructed and tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for one (1) year from the date of purchase. This warranty is limited to the original retail purchaser of the amplifier.
Should the unit fall due to factory defects in material or workmanship, your unit well be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline at 718-236-6948 to obtain a Return Authorization Number.
This R.A # must appear on the outside of your package and on all paperwork relating to your return.
When returning the unit to us for warranty service, it must be carefully packed and shipped, prepaid, to: PYLE PRO Service Center 1600 63rd Street Brooklyn, NY 1 1 204
- You must also include the following items with your return:
- A copy of your sales receipt or other proof of purchase
- A brief letter, indicating the problem you are experiencing with the product
- Include in your return address, daytime phone number and R.A. number
- Also include a check or money order for $20.00 for return shipping, handling and insurance, or provide your Visa/ MC number with expiration date.
Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid. This warranty
will be considered void if the unit was tampered with, improperly serviced or subject to misuse, neglect or accidental damage.
SPECIFICATIONS
- Output power, 2 channels driven
- 4-0HM,1 KHz, 1 % THO 8Wx2
- 4-0HM,1 KHz, 10% THO 10Wx2
- Peak Power 40Wx2
- Total Harmonic Distortion, 1 KHz Rated Power 0.3 %
- Input Sensitivity, 1 KHz A-ohm Rated Power 1S0mV
- Frequency Response 20Hz – 40KHz
- Signal to Noise Ratio 7SdB
- Power Requirement 120V AC 60Hz or 230V AC 50Hz
- Dimensions 1 60x69x1 20mm (WxHxO)
Frequently Asked Questions
Amplifiers shouldn’t be left on since prolonged and continuous heat exposure might cause internal components, including the filament, to wear out. Quality and dependable amplifiers can run continuously for hours, days, or even weeks without experiencing any damage. It’s advisable to switch your amps off when not in use, though.
Problems might arise when there is too little power, which is the opposite circumstance. The voice coil of the speaker it is connected to may become damaged if an amplifier is forced into clipping (distortion) by being pushed to output more power than it is able to supply.
When an amplifier produces far more wattage than your speakers can handle, it may be too powerful for your speakers.
Even if you play a solid-state amplifier every day, it often lasts for more than 30 years. Tube amplifiers have a comparable lifespan, but they also need to be re-tubed every two years.
Designed to run continuously, tube amplifiers. Numerous manufacturers advise against playing for longer than 6 or 8 hours straight without taking a cool-down break of 30 to 60 minutes.
Generally speaking, you should choose an amplifier that has a power output capacity that is double the program/continuous power rating of the speaker. This indicates that an amplifier with a power output of 700 watts into an 8 ohm load is necessary for a speaker with a “nominal impedance” of 8 ohms and a programmer rating of 350 watts.
Speakers may not be able to handle an amp’s power. The amount of electrical energy that speakers can transform into audio is a constraint. Generally speaking, harm is unlikely to occur if the amplifier generates more electrical energy than the speakers can handle. Instead, distortion or clipping may occur.
It is well recognized among audio engineers, audio fans, and musical technicians that amplifiers can harm speakers. At the amplifier stage, over- or under powering your speakers might result in unnatural movement of the cones and coils, harming them.
By giving the speakers too much high-frequency energy and forcing the amplifier into clipping, you risk damaging the speakers if you don’t have a powerful enough amplifier to achieve the desired volume levels.
Yes, it is true that speakers play louder and clearer at higher power levels (watts). However, slight variations in power don’t produce much of an audible difference. The power would need to double in order to perceptibly hear a change (a 3dB increase).
Two speakers are often a manageable load for most amplifiers. Similar to a passenger on a tiny motorbike: carrying two passengers doubles the load that the bike must carry, but most bikes can manage this. However, if you add more speakers than two, the amplifier will typically get overloaded.
Actually, depending on how they were handled, amplifiers can lose power with time.
Set your amplifier’s controls to 7-9 gain, 4-5 bass, 5-7 mids, and 5-7 treble for a distorted tone. Consider lowering the mids and raising the treble and bass for metal. Lower the gain a little bit and boost the mids for severe rock distortion. Remember that this is just the beginning.
If whatever you use to listen to music can achieve that on its own: a lack of power isn’t one of your difficulties. An amplifier’s duty is to raise the power output of your source to the level you want. You may now stop reading and continue listening to your favorite podcasts! Your audio is likely to sound terrible because of something else.
In general, more watts could provide you with greater bass, but only if the amplifier you’re using right now is insufficiently strong for the speakers you’re using. You can get greater bass and louder sound output by swapping out your old amp for another one that has a higher power output.
