PYLE PATVSB260 Sound Bar Speaker System User Guide

WARNING:
This product may expose you to chemicals, which is known to the state of California to cause cancer, birth defects and other reproductive harm. Do not ingest.

For more info go to: www.P65warnings.ca.gov

Technical Specs

Power Supply:
- PATVSB2600: 120 watts RMS / 180 watts peak
- PATVSB3600: 180 watts RMS / 270 watts peak
- PATVSB4600: 240 watts RMS / 360 watts peak
Construction Materials: Aluminum alloy sound bar with silicone buttons
BT Range: Up to 82 ft.
Aluminum Clamp System: Fits 1.5″ – 2″ bars
Frequency Response: 20Hz – 20kHz
Remote Control Battery: Requires 2x ‘AAA’ batteries (not included)
Tweeters: 1 inch

Product Dimensions (L x W x H):
- PATVSB2600: 24.46″ x 4.84″ x 4.05″ -inches
- PATVSB3600: 34.72″ x 4.84″ x 4.05″ -inches
- PATVSB4600: 43.23″ x 4.84″ x 4.05″ -inches

FCC INFORMATION

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION

IMPORTANT SAFETY INSTRUCTIONS

Do not operate mobile equipment while driving a motorized vehicle.
Safe driving and consideration for the safety of others should always be your highest priority.

If you notice smoke, strange noises, odor from this product, or any other abnormal signs, immediately turn off the power and consult your dealer or the nearest authorized PyleUSA Service Center. Using this product in such a condition may result in permanent system damage.
Set your volume control at a low setting, then slowly increase the sound until you can hear it comfortably without distortion or discomfort to your ears.

BE SURE TO OBSERVE THE FOLLOWING GUIDELINES

Do not turn up the volume so high that you cannot hear what’s around you.
Use caution or temporarily discontinue use in potentially hazardous situations.

INSTALLATION PRECAUTIONS

WARNING – Always consult a professional installer:

Do not attempt to install or service this product by yourself. Installation or servicing by persons without professional training and experience in electronic equipment and motorized vehicle accessories may be dangerous and could expose you to electric shock, injury, or other hazards.
This product can be powered from a vehicle’s cigarette lighter/auxiliary power port or hardwired directly to the battery through an optional relay/accessory switch.
While this product has a weather-resistant design, it should not be submerged in or under water.

Use only the installation parts provided with the product.
Clean with mild soap or detergent and lukewarm water using a clean sponge or soft cloth. Rinse well with clean water.

“DON’T” ˜ VERY IMPORTANT

DON’T clean in hot sun or on very hot days.
DON’T use abrasive or highly alkaline cleaners on the main body.
DON’T scrape the main body with razor blades or other sharp instruments.

DON’T use gasoline, acetone, or carbon tetrachloride.

WIRELESS BT OPERATION INSTRUCTIONS

External devices with built-in BT functions can be connected to this sound bar. When your device is connected to the sound bar, you will hear audible tones to assist with the connection process.

First, ensure the sound bar is powered on and the volume is set to low.

Press the “MODE” button on the front panel and select BT mode.
Turn on BT on your external device.
Search for available BT devices. Make sure you are within range of the sound bar and select “PATVSB2600,” “PATVSB3600,” or “PATVSB4600” on your device.

You can now play music from your external device through the sound bar.

FRONT CONTROL PANEL

Display screen

Remote Control Receiver
MODE: Press this button to select the input source.
Light Mode: Press this button to turn the light on/off or change the light color.

Previous Track : Press this button to select the previous track.
Next Track : Press this button to select the next track.
Vol+: Press this button to increase the volume.

Vol-: Press this button to decrease the volume.
Play/Pause : Press this button to play or pause the audio track.

SIDE PANEL FUNCTIONS

3.5mm AUX Input
USB Jack
Cigarette Power Cable Adapter

Fuse (15A)
LED Power Indicator
Control Panel

REMOTE CONTROL

Power Switch
Light Mode: Press this button to turn the light on/off or change the light color.
Number Pad

Repeat: Press to repeat the current song.
Mode: Press to select the input source.
Vol+: Press this button to increase the volume.

Previous Track : Press this button to select the previous track.
Next Track : Press this button to select the next track.
EQ: Press to toggle between preset EQ curves.

Mute
Vol-: Press this button to decrease the volume.
Play/Pause : Press this button to play or pause the audio track.

INSTALLATION METHOD

Take the bracket and screws out of the package.
Follow the installation instructions provided.

CLEANING, MAINTENANCE, AND STORAGE GUIDE

Cleaning

Use a soft, dry cloth to gently wipe the exterior of the sound bar.
For stubborn dirt, use a mild soap or detergent with lukewarm water, and a soft cloth or sponge. Rinse with clean water and dry thoroughly.
Avoid using abrasive materials, harsh chemicals, or solvents such as gasoline, acetone, or carbon tetrachloride, as they may damage the exterior finish.
Do not clean the unit in direct sunlight or on very hot days, as this may affect the finish.

Maintenance

Periodically check all connections to ensure they are secure and free of dust or debris.
Inspect the LED power indicator and ensure it is functioning properly.

Replace the fuse (15A) if needed, and use only the specified fuse type to avoid electrical hazards.
If not in regular use, power off the unit and disconnect it from the power source to preserve battery life.

Storage

Store the sound bar in a cool, dry place away from direct sunlight and extreme temperatures.
If the sound bar is not in use for an extended period, disconnect it from the vehicle’s power source or remove the cigarette power cable adapter.
For added protection, place the sound bar in a padded storage case or cover to prevent dust buildup and potential scratches.

Register Product
Thank you for choosing PyleUSA. By registering your product, you ensure that you receive the full benefits of our exclusive warranty and personalized customer support. Complete the form to access expert support and to keep your PyleUSA purchase in perfect condition.

Start Here

PyleUSA.com/pages/register

www.PyleUSA.com

Documents / Resources

PYLE PATVSB260 Sound Bar Speaker System [pdf] User Guide
PATVSB260 Sound Bar Speaker System, PATVSB260, Sound Bar Speaker System, Speaker System, System

References

User Manual

PYLE PATVSB260 Sound Bar Speaker System

Frequently Asked Questions

Features

Bluetooth Wireless Streaming

WHAT’S IN THE BOX