Nova Suspension Up and Down End Feed
“
Specifications:
- Product Name: Nova Suspension Up and Down End Feed & Glide
Up and Down – End Feed - Model Number: NSUD_P-_-E_-_ GLUD_-_-E_-_
- Mounting: Ceiling mount only
- Dimmable: Yes, with two individual low voltage dimmers
- Installation: Must be done by a qualified electrician in
accordance with local electrical codes
Product Usage Instructions:
Section One: Install the Canopy
- Loosen and remove the four Phillips screws from the canopy to
remove the mounting plate. - Ensure the mounting plate is grounded per local electrical
codes. - Feed the 120VAC power wires through the mounting plate center
hole. - Secure the mounting plate to the junction box using washers and
#8-32 screws.
Section Two: Install the Support Standoff
- Determine the fixture height (H) from the bottom of the channel
to the top of the canopy. - Determine the fixture length (L) by measuring the distance
between coaxial cable and aircraft cable on the channel. Mark
standoff location on ceiling from center of junction box. - Tap the anchor onto marked location up to threaded portion with
a hammer. - Screw in the threaded portion of anchors with a Phillips
screwdriver.
Section Three: Install the Support Canopy (E2 Version)
- Remove the four Phillips screws from the canopy to remove the
mounting plate. - Mark points through mounting plate holes onto ceiling.
- Tap anchors onto marked points up to threaded portion with a
hammer and screw in threaded portion with Phillips
screwdriver. - Secure mounting plate to ceiling using #8 screws.
FAQ:
Q: Can I install this product on a wall
surface?
A: No, this product is designed for ceiling
mount only.
Q: Can I dim this product with any type of
dimmer?
A: This product is dimmable with two individual
low voltage dimmers as specified.
Q: Do I need to ground the mounting plate during
installation?
A: Yes, ensure the mounting plate is grounded
in accordance with local electrical codes for safety.
“`
Doc # 904-NSUDP-E_05
1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.PureEdgeLighting.com info@PureEdgeLighting.com © 2016 PureEdge Lighting. All Rights Reserved.
Installation Instructions for Nova Suspension Up and Down End Feed & Glide Up and Down – End Feed, with Power
IMPORTANT INFORMATION
– This product is ceiling mount only. – Care and Maintenance: Dust the wood panels (if applies)
with a dry rag before cleaning it with a slightly damp rag or towel. – This product is dimmable with two individual low voltage dimmers. – This product must be installed by a qualified electrician and in accordance with local electrical codes.
SAVE THESE INSTRUCTIONS!
NSUD_P-_-E_-_ GLUD_-_-E_-_
Section One: Install the Canopy
A
MOUNTING PLATE
NOTE: Before beginning any electrical work, ensure that power to the electrical box is turned off.
1: Loosen and remove the four Phillips screws from the canopy to remove the mounting plate.
SCREWS
1
CANOPY
B
2: Make sure the mounting plate is grounded in accordance with local electrical codes.
3: Feed the 120VAC power wires through the mounting plate center hole.
4: Secure the mounting plate to the junction box using the washers and #8-32 screws.
#8-32 SCREW
CEILING
2 4
3
MOUNTING PLATE
1
Section Two: Install the Support Standoff
C
CANOPY
STANDOFF
1: Determine the fixture height (H) from the bottom of the channel to the top of the canopy.
H1
COAXIAL CABLES
CHANNEL
AIRCRAFT CABLE
2: Determine the fixture length (L). Measure the distance between the coaxial cable and aircraft cable on the channel. Mark the standoff location on the ceiling from the center of the junction box.
NOTE: Omit Section Seven if the channel is made out of a single piece.
TOP VIEW
2
CANOPY
L STANDOFF
D
NOTE: Steps 3 and 4 are for drywall mounting. Omit these steps if mounting to a wood surface directly.
CEILING
NOTE: Omit steps 3 through 7 if using support canopy. Refer to
Section Three: Install the Support Canopy.
3
3: For each provided standoff, tap the anchor onto the marked
4
location up to the threaded portion with a hammer.
4: Screw in the threaded portion of the anchors with a Phillips screwdriver.
ANCHOR
E
THREADED WASHER
5 #8 SCREW
5: Feed the #8 screw through the threaded washer.
6: Tighten the #8 screw completely into the anchor.
7: Feed the aircraft cable through the threaded post. Tighten
6
the threaded post completely onto the threaded washer.
7
THREADED POST
AIRCRAFT CABLE
Section Three: Install the Support Canopy (E2 Version)
F
1: Remove the four Phillips screws from the canopy to remove the mounting plate.
MOUNTING
PLATE
SCREWS
1
SUPPORT CANOPY
2
G
2
SUPPORT
CANOPY
2
MOUNTING
PLATE
CEILING
NOTE: Step 3 is for drywall mounting. Omit this step if mounting to a wood surface directly.
2: Mark points through the mounting plate holes onto the ceiling.
3: Tap the anchors onto the marked points up to the threaded portion with a hammer. Then screw in the threaded portion with a Phillips screw driver.
CEILING ANCHOR
ANCHOR 3
3
H
#8 SCREW
4
4
CEILING
4: Secure the mounting plate to the ceiling using the #8 screws.
I
SCREWS
THREADED POST AIRCRAFT CABLE
7 5 6
CANOPY
5: Unscrew the threaded post on the canopy.
6: Feed the aircraft cable through the threaded post. Tighten the post completely back onto the canopy.
7: Align the support canopy holes with the mounting plate and secure in place by tightening the four screws.
Section Four: Adjust the Sliding Post
J
1: If the fixture is provided with additional supports in the middle of the channel then loosen (Do Not Remove) the
M3 SET SCREWS
two M3 set screws on the sliding post with a 1.5mm Allen wrench.
1
2: Adjust the position by moving the sliding post across the
SLIDING
channel.
POST
3: Tighten the two M3 set screws.
2 4: Repeat steps 1 through 3 for the remaining supports.
3
K
5
TAB
6
AIRCRAFT CABLE
EXCESS AIRCRAFT CABLE
5: For each standoff or support canopy, insert the aircraft cable through the top of the tab on the sliding post.
6: Adjust the height of the fixture by pushing the tab and pulling the aircraft cable out of the side of the sliding post. Release the tab to secure the cable in place.
Section Five: Install the Coaxial Connector
L
1: Remove the two Phillips screws from the sliding post.
SLIDING POST
1
PHILLIPS
SCREW
M
2
2: Place the back part of the sliding post inside the back of the channel and rotate it into place.
CHANNEL 2
SLIDING POST
N
POWER CABLES
3: Place the other part of the sliding post onto the back of the
4
channel.
CHANNEL
3
4: Ensure that the power cables are in between the two parts
of the sliding post.
SLIDING POST
SLIDING POST
4
O
CHANNEL
5: Insert the two Phillips screws halfway into the sliding post to loosely join the two parts.
PHILLIPS SCREW
6: Adjust the position of the sliding post by moving it across the channel.
5
6
P
SLIDING POST
CHANNEL 7
7: Tighten the two Phillips screws on the sliding post to secure it to the channel.
SLIDING POST
PHILLIPS SCREW
Q
CANOPY
NOTE: If cable is curled or kinked, straighten by holding
between the shaft of a screwdriver and thumb and pulling the
8
cable through (see inset).
8: Split the end of the cable and push each coaxial cable
through the cord grip of the canopy.
CORD GRIP
COAXIAL CABLE
NOTE: Scan the QR Code to watch the video clip of the following steps or visit www.PureEdgeLighting.com/video_feed/installation_ cxc_connector
9: Use the 18AWG hole of the wire stripper to remove 1-3/8″ of the outer insulation to expose the braided wire.
R COAXIAL CABLE
WIRE STRIPPER
10: Use the 18AWG hole of the wire stripper to remove 1″ of the braided wire making sure not to nick the inner wire insulation.
11: Use the 20AWG hole of the wire stripper to remove 1/8″ of the inner insulated wire.
11
BARE WIRE
INNER INSULATION
1/8″ 1″
10
BRAIDED
3/8″
WIRE
OUTER
9
INSULATION
COAXIAL CABLE
5
S
COAXIAL CONNECTOR
COVER
12
COAXIAL CONNECTOR COVER
12: Unscrew the coaxial connector covers and remove from the connector assembly.
CONNECTOR ASSEMBLY
T
2MM ALLEN WRENCH
1.5MM ALLEN WRENCH
14 M3 SET
M4 SET SCREW
SCREW
13
13: Using the provided 1.5mm Allen wrench, remove the M3 set screw from the coaxial connector assembly.
14: Using the provided 2mm Allen wrench to loosen (Do Not Remove) the M4 set screw.
U
COAXIAL CONNECTOR
BRAIDED WIRE
COVER
15
16
FERRULE
15: Slide the connector cover over the coaxial cable.
16: Place the ferrule over the 3/8″ braided wire of the coaxial cable.
V
COAXIAL CABLE
COAXIAL CABLE
17
CONNECTOR ASSEMBLY
CONNECTOR ASSEMBLY
FERRULE
17: Insert the coaxial cable into the coaxial connector until the wires of the center conductor are visible through the M3 set screw hole.
NOTE: Ensure that the split in the ferrule is aligned 90° from the M4 set screw (see inset).
6
W
1.5MM ALLEN
WRENCH 18
M3 SET SCREW
18: Use the provided 1.5mm Allen wrench to replace and securely tighten the M3 set screw.
COAXIAL CABLE
CONNECTOR ASSEMBLY
X
19
2MM ALLEN WRENCH
M4 SET SCREW
19: Use the provided 2mm Allen wrench to securely tighten the M4 set screw until it squeezes the wire ferrule tightly to the coaxial cable.
COAXIAL CABLE
CONNECTOR ASSEMBLY
Y
COAXIAL CABLE
COAXIAL CONNECTOR
20: Replace the coaxial connector cover and tighten into place.
20
COVER
21: Repeat steps 9 through 20 for connecting the other
coaxial connector to the second coaxial cable.
NOTE: Make sure that these coaxial connectors are placed inside the power supply housing. DO NOT place these inside the junction box.
Section Six: Power the Fixture
Z
2
3
1
1: Connect the white wire of one transformer to the 120VAC neutral wire using a wire nut.
2: Connect the black wire of the same transformer to the 120VAC line wire of the same circuit using a wire nut.
3: Repeat steps 1 and 2 for connecting the second transformer wires to the other circuit line voltage wires.
7
Z1
4
JUNCTION BOX
4: Place all line voltage wires and wire nut connections inside the junction box.
Z2
5: Align the canopy holes and secure the canopy in place by tightening the four screws.
6: For fine adjusting the fixture height, push the cord grip to slide the fixture up and down until the desired height is achieved. Release the cord grip to lock the cables in place.
SCREW CORD GRIP
COAXIAL CABLE
5
6 CANOPY
Z3
7: Install the optional louver to complete the channel assembly by pushing onto the channel over the lens.
LENS
7
LOUVER
Section Seven: Multiple Channel Sections
Z4
NOTE: If applicable, multiple channels must be installed one by
2
one.
NOTE: Omit this section if the joiner did not come with the fixture depending on the overall fixture length.
1
AIRCRAFT 3 CABLE
JOINERS CHANNEL
JOINER JOINER
JOINER
NOTE: Omit steps 1 through 5 if the joiner did not come with aircraft cable depending on the overall fixture length. 1: Insert the aircraft cable through the top of the tab on the
joiner.
2: Lift the other end of the aircraft cable against the ceiling to mark the location of the standoff.
3: Push the tab on the joiner and remove the aircraft cable.
4: Refer to Section Two or Three to install the supports on the ceiling and adjust the fixture height.
8
Z5
AIRCRAFT CABLE
5
5
CORD GRIP
5: For each standoff, insert the aircraft cable through the cord grip on the top joiner and pull the aircraft cable out of the side.
JOINER
Z6 CHANNEL 6
6: Loosen the four #2-56 set screws on the top joiner using a 0.035″ Allen wrench and slide it inside the channel.
#2-56 SET SCREW
Z7
LED STRIP
8
7: Align the female connector of the bottom LED strip on the channel with the bottom section of the other channel.
LED STRIP
8: Slide the channel over the joiners. Ensure the connectors
7
of the LED strips mate properly.
MALE CONNECTOR
FEMALE CONNECTOR
Z8
9: Lift a section of the top lens at the end of the channel. If the set screws are not visible, slightly pull back the top LED strip to expose the set screw holes.
10: Secure the channel by tightening the two #4-40 set screws using a 0.05″ Allen wrench.
11: Connect the male & female connectors of the top LED strips. Firmly press down the adhesive portion of the LED strip onto the channel, making sure there are no air bubbles that can cause surface irregularities.
SET SCREW
10
9
Z9
#2-56 SET SCREW
15
AIRCRAFT CABLE
14
13
LENS
JOINER
12
12: Press the lens back onto the channel.
13: Slide the top joiner back to the proper location and tighten the eight #2-56 set screws to lock it in place.
14: Adjust the height of the fixture by pushing the tab and pulling the aircraft cable out of the side of the joiner. Release the tab to secure the cable in place.
15: If necessary, trim excess aircraft cable using sharp cutters.
Wiring Diagram
N L
N L
N
LOAD
GND L
ELV DIMMER
INPUT 120VAC
LOAD
N
GND L
ELV DIMMER
INPUT 120VAC
10
Documents / Resources
 |
PURE EDGE Nova Suspension Up and Down End Feed [pdf] Installation Guide 904-NSUDP-E_05, Nova Suspension Up and Down End Feed, Suspension Up and Down End Feed, Up and Down End Feed, Down End Feed |