Pulsar X2A v3 eS Mini Wireless Mouse
Product Information
Specifications
- Model: Pulsar X2A v3 eS Mini Wireless Mouse
- User Manual Date: 2023-09-11
- Version: V1.0
- Working Modes: Wired and RF
- Polling Rate Range: 500Hz-8000Hz (Wired mode), 500Hz-4000Hz (Wireless mode)
- LOD Setting Range: 1mm-2mm
- Motion Sync Setting: ON/OFF
Product Usage Instructions
Basic Functions
The mouse has the following basic functions:
- Left mouse button
- Forward button
- Backspace button
- Right mouse button
- Middle mouse button
- Mouse scroll
Indicator Light
The mouse has indicator lights for:
- Mouse RF connection indicator
- Dongle RF connection indicator
Working Mode Switching
The toggle switch allows you to switch between wired and RF modes.
DPI Setting
DPI settings can be adjusted for sensitivity.
Polling Rate Setting
Follow the steps to set the polling rate for wired and wireless modes.
LOD Setting
Adjust the Lift-off Distance (LOD) setting by following the steps provided.
Motion Sync Setting
Set the Motion Sync to ON or OFF as per your preference.
FCC Caution
Ensure compliance with FCC Rules and avoid modifications that could void operation authority.
Basic function
Indicator light
Working mode switching
Toggle switch,
- wired mode when moved to the left “X“;
- RF mode when moved to the right “O“;
DPI Setting
- Gather Step 1: Press the “DPI” switch to light the OLED, and the OLED will display the current set values;
- Gather Step 2: Press the switch again, set the DPI value, at this time OLED will only display the DPI value, other Settings will be hidden;
- Gather Step 3: After the setting is complete, wait 3 second, OLED will display the current overall setting values;
- Gather Step 4: Wait another 3 second and the OLED will turn off;
DPI sets the step level 400-800-1600-3200-6400-12800 Back and forth cycle
Polling Rate Setting
- Gather Step 1: Press the “HZ” switch to light the OLED, and the OLED will display the current set values;
- Gather Step 2: Press the switch again, set the polling rate value, at this time OLED will only display the polling rate value, other Settings will be hidden;
- Gather Step 3: After the setting is complete, wait 3 second, OLED will display the current overall setting values;
- Gather Step 4: Wait another 3 second and the OLED will turn off;
- Wire mode polling rate sets the step level 500Hz-1000Hz-2000Hz-4000HZ-8000Hz Back and forth cycle
- Wireless mode polling rate sets the step level 500Hz-1000Hz-2000Hz-4000HZ
- Back and forth cycle
LOD Setting
- Gather Step 1: Press the “HZ” switch to light the OLED, and the OLED will display the current set values;
- Gather Step 2: Hold down the “HZ” switch and set the LOD height value by pressing the right mouse button. At this time, OLED will only display the current LOD set value, and other set values will be hidden;
- Gather Step 3: After the setting is complete, wait 3 second, OLED will display the current overall setting values;
- Gather Step 4: Wait another 3 second and the OLED will turn off;
- LOD sets the step level
- 1mm—2mm
- Back and forth cycle
Motion Sync Setting
- Gather Step 1: Press the “HZ” switch to light the OLED, and the OLED will display the current set values;
- Gather Step 2: Hold down the “HZ” switch and press the right mouse button to enable or disable the “Motion Sync” function. At this point, the OLED will only display the current set value, and other set values will be hidden;
- Gather Step 3: After the setting is complete, wait 3 second, OLED will display the current overall setting values;
- Gather Step 4: Wait another 3 second and the OLED will turn off;
- Motion Sync sets the step level
- ON—OFF
- Back and forth cycle
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
FAQ
Q: How can I switch between wired and RF modes?
A: Use the toggle switch on the mouse to move between wired and RF modes.
Q: How do I adjust the DPI settings?
A: The DPI settings can be adjusted using the provided software or buttons on the mouse, depending on the model.
Q: What is the range of polling rates supported by the mouse?
A: The mouse supports polling rates ranging from 500Hz to 8000Hz in wired mode and 500Hz to 4000Hz in wireless mode.
Documents / Resources
 |
Pulsar X2A v3 eS Mini Wireless Mouse [pdf] User Manual PX2A3ES11, 2A2TU-PX2A3ES11, 2A2TUPX2A3ES11, X2A v3 eS Mini Wireless Mouse, X2A v3 eS, Mini Wireless Mouse, Wireless Mouse, Wireless, Mouse |