T019-03 TVL Sending Unit
“
Specifications:
- Product Name: TPMS Sending Unit, Harness, and Repeater
- Application: Truck/Tractor
- Manufacturer: Clarience Technologies
Product Usage Instructions:
Introduction:
The TPMS Sending Unit, Harness, and Repeater are essential
components for monitoring tire pressure in truck and tractor
applications.
Sending Unit, Harness, and Repeater Components:
The components include TireView Sending Unit, TireView Repeater,
Wire Harness, Hardware Bag, Cable Ties, and Decals.
Installation Steps:
- Mounting Location:
- Identify suitable mounting locations for the sending unit and
repeater. - Recommended placement for the sending unit is behind the
driver’s seat. - Repeater should be placed near the first drive axle or
optionally behind the center console. - Avoid mounting the repeater surrounded by metal to prevent
signal interference.
- Identify suitable mounting locations for the sending unit and
- Mounting Process:
- Use the sending unit as a template to mark and drill mounting
holes with a 3/8 drill bit. - Attach the sending unit using supplied bolts, washers, and
locknuts. Torque bolts to 8-10 ft.-lbs. - If mounting to the cab, seal penetrations with Silicone RTV to
prevent damage. - Mount the repeater using cable ties, bolts, or rivets. Secure
the repeater harness and route towards the battery box.
- Use the sending unit as a template to mark and drill mounting
Frequently Asked Questions (FAQ):
1. What is the purpose of the repeater in the TPMS system?
The repeater helps ensure proper operation of the TireView
system by extending the signal range between the sending unit and
the monitor.
2. Can I mount the sending unit anywhere in the vehicle?
It is recommended to consult with the vehicle owner/operator or
management before mounting the sending unit to ensure proper
placement and functionality.
“`
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
INSTALLATION MANUAL
TireView® LIVETM Sending unit, Harness and Repeater Installation
Truck/Tractor Applications
www.psitireinflation.com/resources#tpms-resources
© 2025 Pressure Systems International, LLC.
1
A Clarience Technologies Company.
V019 05 TVL Tractor Install Video
T019-03 Rev 08-25
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
About this Manual This manual supplies installation procedures for the TireView® LIVETM sending unit. Use the procedures in this manual to install the system on commercial vehicles. Before You Begin
CAUTION: DO NOT PERFORM UNAUTHORIZED MAINTENANCE OR REPAIR PROCEDURES, OR INSTALL NON-P.S.I.® COMPONENTS ON ANY P.S.I. ® SYSTEM. THIS CAN VOID THE WARRANTY. 1. Read and understand all instructions and procedures before service to components begins. 2. Read and observe all Warning and Caution alert messages in this publication. They provide information that can prevent personal injury, damage to components, or both. 3. Follow the P.S.I. installation, maintenance, service, and troubleshooting guidelines. 4. Use special tools, when required, to avoid personal injury and damage to components. 5. Use personal protective equipment (PPE), when required, to avoid personal injury. Safety glasses, safety toe shoes, and gloves recommended.
Hazard Alert Messages and Torque Symbols
WARNING: A Warning alerts the technician to an instruction or procedure that must be followed to avoid personal injury and damage to components.
CAUTION:
A Caution alerts the technician to an instruction or procedure that must be followed to avoid damage to components.
TORQUE REQUIRED: The torque symbol alerts the technician to tighten fasteners to a specified torque value.
Additional Information Visit the Resource section at www.psitireinflation.com to access and request additional information. Call P.S.I.® at 210.222.1926 (United States and Canada) or email info@psitireinflation.com or techsupport@psitireinflation.com.
Introduction
The P.S.I.® TireView® Tire Pressure Monitoring System (TPMS) is designed to monitor air pressure and temperature in the tire. It is only for added safety and not meant to replace regular tire maintenance and exercise of reasonable care when operating a motor vehicle. The system cannot prevent accidents nor will P.S.I.® be responsible for damage or injury due to (a) improper use,(b) failure to follow the product manufacturer’s instructions or to perform preventative maintenance, (c) unauthorized repair or modifications, (d) use of products beyond their useful life, or (e) external causes such as accidents, abuse, or other actions or events outside of P.S.I.® control.
© 2025 Pressure Systems International, LLC.
2
A Clarience Technologies Company.
T019-03 Rev 08-25
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
Introduction
This manual is intended to provide guidance when installing the TireView® LIVETM sending unit and repeater on a commercial truck, tractor, or similar vehicle. Your configuration may vary due to type of equipment. Consult your support team for guidance.
Sending Unit, Harness and Repeater Components
PART DESCRIPTION
EXAMPLE
TireView Sending Unit
TireView Repeater
Wire Harness
Hardware Bag Cable Ties
Decals
© 2025 Pressure Systems International, LLC.
3
A Clarience Technologies Company.
T019-03 Rev 08-25
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
Installation Steps
1. Identify suitable mounting location for the TireView LIVE (TVL) sending unit and repeater. See Figure 1.
CAUTION: The repeater must be installed to help ensure proper operation of the TireView system. Failure to install the repeater could void warranty.
Sending unit
RECOMMENDED PLACEMENT: mounted on the interior behind the driver’s seat.
NOTE: Consult vehicle owner operator, fleet owner, or management before mounting sending unit to cab.
= TireView Repeater = TireView Sending Unit
CAUTION: Do not mount sending unit where tires can throw debris onto enclosure as this could cause damage.
CAUTION: Make sure location is suitable to route power wire harness to the sending unit.
Repeater
RECOMMENDED PLACEMENT: near the first drive axle, central on the vehicle. See Figures 1 & 3.
OPTIONAL PLACEMENT: in cab, behind center console, minimum 3 feet from the Sending Unit if possible. See Figures 1 & 2.
CAUTION: Avoid mounting the repeater where it is surrounded by metal (i.e., inside a cross member). This can prevent sensor signals from reaching the sending unit and will cause loss of data.
Figure 1: Sending unit and repeater location.
© 2025 Pressure Systems International, LLC. A Clarience Technologies Company.
Figure 2: Optional repeater location.
4
T019-03 Rev 08-25
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
2. Using the TVL sending unit as a template, mark mounting hole locations and drill with a 3/8″ drill bit. See Figure 2.
3. Use supplied bolts, washers, and locknuts to attach sending unit to vehicle.
TORQUE mounting bolts to 8-10 ft.-lbs.
CAUTION: If mounting to the cab, seal any penetrations into the body with Silicone RTV when attaching the sending unit. Screws and sealant are not included in the kit for this installation method. Technician is responsible to ensure no damage is done to equipment inside cab.
4. Mount the repeater using cable ties (included), bolts, or rivets. Repeater harness should be secured to factory wire harness or air lines with supplied cable ties and route towards the battery box. See Figure 3.
Wire Harness Connection
5. Starting at the component furthest from the fuse panel (usually the repeater) connect one lead of the wire harness to the Weather Pack connector on the component harness. Secure harness to factory wire harness or air lines with supplied cable ties and route towards the fuse panel.
NOTE: The supplied wire harness has 2 preterminated Weather Pack connectors. One lead is longer than the other, but the connectors are electrically the same. Use the proper length lead for each component. See Figure 4.
6. Connect the second lead of the wire harness to the Weather Pack connector on the remaining component. Secure harness to factory wire harness or air lines with supplied cable ties and route towards the fuse panel.
Figure 2
Figure 3: Recommended repeater location. WEATHER PACK CONNECTORS
© 2025 Pressure Systems International, LLC. A Clarience Technologies Company.
Figure 4
5
T019-03 Rev 08-25
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
7. Connect ring terminals of the harness to the fuse panel, ensuring positive (+) and negative (-) leads are on correct terminals. Secure any excess harness using supplied cable ties. Ensure wire harness does not interfere with installation of fuse panel cover, if applicable. Verify 2A fuse is installed in wiring harness fuse holder. See Figure 5.
Negative (-) wire here
Positive (+) wire here
Power on System
8. When power is applied, verify status lights on TVL sending unit. See Figure 6.
TireView LIVE Receiver indicator light
LED Signal ACQUIRED
(Signal)
(Blinking)
NO LIGHT
RED
Check power connection
Figure 5
TireView LIVE Sending Module indicator lights
LED
SEARCHING for Signal ACQUIRED
(Signal) Signal (Blinking)
(Solid)
GREEN (GPS)
AMBER (Cellular)
NOTE: If green or amber lights do not turn solid, move vehicle outdoors or to an area with better cellular coverage.
Install Decals
9. Consult vehicle owner operator, fleet owner, or management for decal placement. Clean surface prior to decal installation.
Figure 6
NOTE: Do not place decals on sending unit cover or obstruct sending unit barcode label.
Program Sensors to System
10. Use the mobile app (Goodyear® TPMS PlusTM, TireView LIVE, etc.) to program the system and install sensors.
© 2025 Pressure Systems International, LLC.
6
A Clarience Technologies Company.
T019-03 Rev 08-25
TPMS Sending Unit, Harness and Repeater Installation
Truck/Tractor Applications
Record of Revisions
Revision Number
Revision Date
By
A
October 03, 2024
CS
B
August 20, 2025
CS
© 2025 Pressure Systems International, LLC.
7
A Clarience Technologies Company.
T019-03 Rev 08-25
Pressure Systems International 4323 Interstate Way, San Antonio, TX 78219 USA Phone: 210.222.1926, Fax: 210.568.4221 www.psitireinflation.com
Visit www.psitireinflation.com/resources or scan this QR code for access to the latest revision of this manual.
© 2025 Pressure Systems International, LLC.
8
A Clarience Technologies Company.
T019-03 Rev 08-25
Documents / Resources
 |
PSI T019-03 TVL Sending Unit [pdf] Installation Guide T019-03, Rev3, T019-03 TVL Sending Unit, T019-03 TVL, Sending Unit, Unit |