PSI T019-01 Flow Thru Bracket Installation Guide

The TireView Flow-Thru Bracket, Hose, and Sensor are designed
for truck and tractor applications to monitor tire pressure and
provide real-time data for improved safety and efficiency.

Product Usage Instructions

1. Installation

Follow the steps below for installing the Flow-Thru Bracket,
Hose, and Sensor:

Consult the provided manual for specific instructions based on
your vehicle type.

Identify the components: TireView Flow-Thru Bracket, Check Port
(CP) Hoses, and TireView TPMS Cap Sensor.
Install the components according to the guidelines provided,
ensuring proper placement and connection.

Refer to the Dual Tire Installation Procedures for aligning
sensors on both inside and outside tires.

2. Servicing

Regular servicing of the system is essential for optimal
performance. Follow these steps:

Refer to the servicing videos provided by the manufacturer for
detailed instructions.
Check for any leaks or damages to the hoses or sensors during
servicing.

Ensure all components are securely fastened and functioning
correctly.

FAQ

Q: How do I pair the TireView TPMS Cap Sensor with the
receiver?

A: Sensors are not paired with the receiver. Refer to the
separate installation manual for the pairing procedure.

Q: Can I install the system on any type of vehicle?

A: The system is designed for truck and tractor applications.
Contact P.S.I. Support for additional configurations or
compatibility questions.

“`

View Fullscreen

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications
INSTALLATION MANUAL
TireView Flow-Thru Bracket, Hose and Sensor Installation & Servicing

Truck/Tractor Applications
V019-01 TVL Flow Thru Bracket Install Video

www.psitireinflation.com/resources#tpms-resources

A Clarience Technologies Company.

V019 06 Servicing Wheels with Flow Thru Brackets Video https://youtu.be/Qs3AqKAp20A
T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications
About this Manual
This manual provides installation and maintenance procedures for TireView® TPMS by P.S.I. Use the procedures in this manual to install the system on commercial vehicles. Before You Begin
CAUTION: DO NOT PERFORM UNAUTHORIZED MAINTENANCE OR REPAIR PROCEDURES, OR INSTALL NON-P.S.I.® COMPONENTS ON ANY P.S.I. ® SYSTEM. THIS CAN VOID THE WARRANTY. 1. Read and understand all instructions and procedures before service to components begins. 2. Read and observe all Warning and Caution alert messages in this publication. They provide information that can prevent personal injury, damage to components, or both. 3. Follow the P.S.I. installation, maintenance, service, and troubleshooting guidelines. 4. Use special tools, when required, to avoid personal injury and damage to components.
Hazard Alert Messages and Torque Symbols
WARNING: A Warning alerts the technician to an instruction or procedure that must be followed to avoid personal injury and damage to components.
CAUTION:
A Caution alerts the technician to an instruction or procedure that must be followed to avoid damage to components.
TORQUE REQUIRED:
The torque symbol alerts the technician to tighten fasteners to a specified torque value.
Additional Information Visit the Resource section at www.psitireinflation.com to access and request additional information. Call P.S.I.® at 210.222.1926 (United States and Canada) or email info@psitireinflation.com or techsupport@psitireinflation.com.
Introduction
The P.S.I.® TireView® Tire Pressure Monitoring System (TPMS) is designed to monitor air pressure and temperature in the tire. It is only for added safety and not meant to replace regular tire maintenance and exercise of reasonable care when operating a motor vehicle. The system cannot prevent accidents nor will P.S.I.® be responsible for damage or injury due to (a) improper use,(b) failure to follow the product manufacturer’s instructions or to perform preventative maintenance, (c) unauthorized repair or modifications, (d) use of products beyond their useful life, or (e) external causes such as accidents, abuse, or other actions or events outside of P.S.I.® control.

A Clarience Technologies Company.

T019-01 Rev 08-25

Record of Revisions
Revision Number A
B
C

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications

Revision Date

April 5, 2024

May 1, 2024

August 20, 2025

Truck/Tractor Tire Hose Reference Chart by Vehicle Type*

*Length (Ref.)

Tire Size

Vehicle Type

16.0″ Ford E-Series

Flow-thru Bracket Sub-Assy
70611-00

Inside Hose

OAL Length

Part #

13.0″

31373-13-CP

Outside Hose

OAL Length

Part #

11.5″

31368-11.5-CP

19.5″ Ford Stripped Chassis 70610-00

13.0″

31367-13-CP

11.5″

31368-11.5-CP

19.5″ Freightliner

70607-00

12.5″

31373-12.5-CP

12.5″

31363-12.5-CP

19.5″ Hino Small Box

70608-00

14.5″

31373-14.5-CP

13.5

31363-00-CP

19.5″ Isuzu

70609-00

15.0″

31373-15-CP

12.0″

31363-12-CP

22.5″ Hino Large Box (L6)

70601-00

17.0″

31373-00-CP

* Contact P.S.I. Support for additional configurations: setup@tireview.com

13.5″

31363-00-CP

A Clarience Technologies Company.

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications

Introduction
This manual is intended to provide guidance when installing Flow-thru Bracket, Hose and Sensor accessories for the system on drive and trailer axles. Your configuration may vary due to type of equipment. Consult your support team for guidance.

Flow-thru Bracket, Hose and Sensor Components

PART DESCRIPTION
TireView Flow-Thru Bracket
· Mounts to wheel end utilizing existing drive wheel axle end cap nuts or trailer hub cap bolts.
· Applications vary by vehicle.
· Consult fitment guide for correct part number and manufacturer recommended torque settings for installation
· Cap sensors and hoses connect to flowthru bracket by hand
Check Port (CP) Hose – INSIDE TIRE
· Inside Tire configuration
· Application lengths vary by vehicle.
· Consult fitment guide for correct part number and length
Check Port (CP) Hose – OUTSIDE TIRE
· Outside Tire configuration
· Application lengths vary by vehicle.
· Consult fitment guide for correct part number and length
TireView TPMS Cap Sensor*
· Secured to backside of Flow-Thru Brackets
· Inside and outside tire positions

“I”-Inside TIRE

EXAMPLE “O”-Outside TIRE
*Length (Ref.) *Length (Ref.)

TireView TPMS Flow-Thru Sensor*
· Used on front steer tires
· Dual seal valve cap allows air check or add without removing sensor

* NOTE: Sensors are not paired with receiver. See separate installation manual for pairing procedure.

A Clarience Technologies Company.

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications

Dual Tire Installation Procedures
1. On dual-wheel installations, ensure valve stems are clocked 180° from each other. If valve stems are clocked incorrectly, remove lug nuts, re-clock wheels, and reinstall lug nuts. See Figure 1. Torque lug nuts to factory specifications.

OUTSIDE TIRE

OUTSIDE WHEEL
VALVE STEM

INSIDE TIRE
INSIDE WHEEL VALVE STEM

Figure 1: 180º Valve Stem Orientation.
NOTE: On wheels with 5-hole cutouts, valve stems cannot be exactly 180 degrees apart, but should be as close as possible. See Figure 2.

Figure 2: 5-hole wheel example.

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications

2. Remove tire valve cap from drive tire. Ensure tire valve threads are clean and free of any debris. Connect straight hose to inside wheel valve stem. Connect hose with 180º bend union to outside wheel valve stem. Hand-tighten plus an additional 1/2 turn using a 7/16″ wrench. See Figure 3.

INSIDE TIRE

OUTSIDE TIRE

CAUTION: Do not overtighten the hose connections. This could damage the hose seal and cause the tire to deflate. Damage to components can occur.

Figure 3: Connect hoses to inside and outside wheels.
3. After sensor programming, install valve cap sensors on fittings labeled “I” for inside and “O” for outside on the back side of the bracket. Hand-tighten the cap sensors until they bottom out, and then slightly twist the cap sensors to fully seat them. See Figure 4.
NOTE: Sensors can be installed on bracket before or after bracket is installed to vehicle.
CAUTION: Do not overtighten the sensor caps. Damage to the sensor cap and threads can occur.

Figure 4: Install cap sensors on Flow-Thru Brackets.

A Clarience Technologies Company.

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications

4. Connect hose to bracket using knurled fitting, matching “I” to inside hose and “O” to outside hose Leave knurled fittings slightly loose. See Figure 5.

CP HOSE FOR OUTSIDE TIRE

CHECK PORT

CAUTION: The knurled ends on the CP hoses are to be hand-tightened only. Do not use tools to tighten. Damage to the knurled ends can occur.

CAP SENSOR

5. Hold bracket up to wheel end or hubcap to determine what mounting bolts will be used to ensure best fitment. Remove corresponding bolts or studs on wheel end or hubcap. See Figure 6.
CAUTION: Do not twist or kink the hoses during installation. Hoses should not contact wheel.

FLOW-THRU BULKHEAD FITTING

CHECK PORT

CP HOSE FOR INSIDE TIRE

Figure 5: Connect hoses to bracket.

FLOW-THRU NYLOCK® BRACKET HALF NUT

6. Mount brackets to wheel ends:
WARNING: Refer to specific vehicle manufacturer torque specifications for drive axle cap nuts and hub cap bolts before installing.
6a. Drive axles: slide bracket over existing axle cap studs, and install provided Nylock half nuts onto studs, or re-use existing axle cap nuts or bolts. See Figure 7.
Torque drive axle cap nuts or bolts to manufacturers specifications.
6b. Trailer axles: align flow-thru bracket and reinstall hub cap bolts through bracket mounting holes and hub cap.
Torque hub cap bolts to hub cap manufacturer specifications (typically 12-16 ft-lbs.).
NOTE: Some vehicles may be equipped with chrome or other cosmetic hub cap wheel coverings. These wheel coverings must be removed and discarded to enable Flow-Thru Bracket installation. See Figure 8.

Figure 6: Determine bracket mount location.

Figure 7: Install bracket to drive axle or trailer axle wheel end.

BEFORE

AFTER

Figure 8: Cosmetic wheel coverings must be removed.

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications
7. Finish hand-tightening knurled hose fittings into bracket. Verify hose is properly seated into the bulkhead by grabbing the check port and turning it back and forth, left to right. If hose turns freely inside bulkhead, continue to tighten the knurled fitting by hand until resistance is felt and hose stops rotating. See Figure 9.
CAUTION: The knurled ends on the hoses are to be hand-tightened only. Do not use tools to tighten. Damage to the knurled ends can occur.

8. Note orientation of the Check Ports on the CP hoses. Check ports should face outward, pointing away from the wheel to enable air check and add air. See Figure 10.
NOTE: Do not to force check ports to face outward if it causes the hose to rub on the wheel.
9. Verify double-seal valve caps are tight on check ports. Depress check port cap and listen for air escaping to verify pressure is getting to hose and sensors.

Figure 9: Hand-tighten knurled hose fittings.
PREFERRED orientation
pointing away from
wheel

10. Spray all connection points between valve stem, hose, and sensors with soapy water to ensure no leaks. Tighten hose if necessary. See Figure 11.

Figure 10: Correct orientation of check ports.

Figure 11: Check for air leaks.
8

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications
Front Steer Tire Installation Procedure
1. Remove tire valve cap from front steer tire. Ensure tire valve threads are clean and free of any debris. See Figure 12.
Figure 12: Prepare front tire valve for flow-thru sensor.
2. Install and hand-tighten the flow-thru sensor until it bottoms out, and then slightly twist the sensors to fully seat it. See Figure 13.
Figure 13: Front steer flow-thru sensor installed.

A Clarience Technologies Company.

T019-01 Rev 08-25

Flow-Thru Bracket, Hose and Sensor Installation
Truck/Tractor Applications
Servicing Wheel/Tire Assembly with Flow-Thru Brackets
1. Remove both knurled hose fittings to remove them from the bracket (dual wheel applications). See Figure 14.

2. Unbolt the lug nuts and remove the wheel(s) from the vehicle. See Figure 15.
CAUTION: Do not allow wheel to drop onto or contact the bracket.
3. Remove the hose from the valve stem using a 7/16′” wrench and set aside.

Figure 14: Remove hose(s) from bracket.

4. When wheel or tire maintenance is completed, reconnect hoses to valve stems per previous instructions in this manual, checking for leaks. See Figure 16.

Figure 15: Remove wheel(s).

5. Reinstall the wheel over the hub & bracket, ensuring the inner wheel valve stem aligns with the “I” in the bracket and the outer wheel valve stem aligns with the “O”. Reinstall the lug nuts and torque to manufacturers specifications. See Figure 17.

Figure 16: Remove hose.

CAUTION: Do not allow wheel to drop onto or contact the bracket.

6. Insert the hose knurled fitting onto the bracket and hand tighten the inner and outer hose to the bracket marked “I” and “O”. See Figure 17.
7. Ensure the double seal valve caps are tightened to the check ports, then depress the valve cap push rod to verify pressure is holding through the hoses and sensors. Finally, check all connections for leaks per previous instructions in this manual. See Figure 17.

A Clarience Technologies Company.

Figure 17: Reinstall over hub & bracket and reinstall hoses. T019-01 Rev 08-25

Pressure Systems International 4323 Interstate Way, San Antonio, TX 78219 USA Phone: 210.222.1926, Fax: 210.568.4221

Visit www.psitireinflation.com/resources or scan this QR code for access to the latest revision of this manual.

www.psitireinflation.com/resources#tpms-resources

A Clarience Technologies Company.

T019-01 Rev 08-25

Documents / Resources

PSI T019-01 Flow Thru Bracket [pdf] Installation Guide
T019-01, T019-01 Flow Thru Bracket, T019-01, Flow Thru Bracket, Thru Bracket, Bracket

References

User Manual

PSI T019-01 Flow Thru Bracket Installation Guide

T019-01 Flow Thru Bracket

Specifications

Product Information

Product Usage Instructions

1. Installation

2. Servicing

FAQ

Q: How do I pair the TireView TPMS Cap Sensor with the
receiver?

Q: Can I install the system on any type of vehicle?

Documents / Resources

References

Leave a comment

Cancel reply