THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
د چټک پیل لارښود

د بسته محتويات

مشخصات

د فابریکې ری سیٹ

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

د QR کوډ سکین کړئ view تفصیلات

https://bit.ly/488mkj9

د ستونزو حل کول

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. وسیله به فعاله نشي
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

د FCC تنظیمي موافقت
دا وسیله د FCC مقرراتو 15 برخې سره مطابقت لري. عملیات د لاندې دوه شرایطو تابع دي: (1) دا وسیله ممکن د زیان رسونکي مداخلې لامل نشي ، او (2) دا وسیله باید هر ډول مداخله ومني ، پشمول هغه مداخله چې ممکن د ناغوښتل شوي عملیاتو لامل شي.
هر ډول بدلونونه یا تعدیلات چې د موافقت لپاره مسؤل ګوند لخوا په څرګند ډول تصویب شوي ندي کولی شي د تجهیزاتو چلولو لپاره د کارونکي واک باطل کړي.
یادونه: دا تجهیزات ازمول شوي او موندل شوي چې د B ټولګي ډیجیټل وسیلې لپاره محدودیتونو سره مطابقت لري ، د FCC مقرراتو 15 برخې سره سم.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- د ترلاسه کونکي انتن بیا ځای په ځای کول یا ځای په ځای کول.
- د تجهیزاتو او رسیدونکي ترمینځ جلا کول ډیر کړئ.
- تجهیزات په یوه سرکټ کې په یوه پلورنځي کې وصل کړئ له هغه څخه توپیر چې ترلاسه کونکی ورسره وصل دی.
- د مرستې لپاره د ډیلر یا تجربه لرونکي راډیو / تلویزیون تخنیکین سره مشوره وکړئ.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

د محدود تضمین لپاره، مهرباني وکړئ لیدنه وکړئ
https://thirdreality.com/faq-help-center/
د پیرودونکي ملاتړ لپاره، مهرباني وکړئ موږ سره اړیکه ونیسئ
info@3reality.com یا لیدنه وکړئ www.thirdreality.com
د نورو پلیټ فارمونو په اړه د پوښتنو لپاره، اړونده ویب پاڼې ته مراجعه وکړئ
platform’s application/support platform.