Manuals+
AirLive OLT and ONU Setup Guide

Setup guide for OLT and ONU in Default Configuration

For the AirLive XGSPON OLT-2XGS and ONU-10XG(S)-1001-10G

Introduction

This guide details the setup process for AirLive XGSPON OLT-2XGS and ONU-10XG(S)-1001-10G devices when used in combination with a router. The setup described uses an AirLive GPON OLT-2XGS and an Airlive ONU-10XG(S)-AX304P-2.5G. Please note the following VLAN restrictions for this configuration: 0, 1, 2, 9, 8, 10, 4000, 4005, 4012-4017, 4095.

Network Diagram Overview

The network topology involves the following components:

  • WAN connection feeding into a Router.
  • The Router acts as a DHCP Server with IP 192.168.110.1.
  • The Router connects to the AirLive XGSPON OLT-2XGS via its GE3 port using VLAN 100. The OLT's managed IP is 192.168.8.200.
  • The OLT connects to a PON Splitter.
  • The Splitter connects to the AirLive ONU-10XG(S)-AX304P-2.5G.
  • The ONU has two LAN ports (1 and 2) which connect to PCs. The ONU's LAN IP is 192.168.1.1.
  • A PC connected to the ONU receives an IP address from the Router, typically in the range of 192.168.110.x (e.g., 192.168.110.25).

Configuration Steps

Follow these steps to configure the OLT and ONU for internet access.

Step 1-4: OLT VLAN Configuration

  1. Login to the OLT management web interface using the default IP 192.168.8.200 via the AUX port. Ensure the correct PON mode for the ONU is selected.
  2. To enable ONU internet access, a VLAN must be created in the OLT first.
  3. Create a VLAN with ID 100 for internet access (this example uses VLAN 100).
  4. Configure VLAN bindings for the uplink GE port. If the uplink port is in "Untag" mode, the PVID (default VLAN ID) must be set to 100.

Detailed VLAN Configuration:

  • Navigate to OLT Configuration > VLAN.
  • Under "New VLAN", set Mode to "single", VLAN ID to 100, and Description to "VLAN100". Click [Add]. The VLAN Table will show VLAN ID 100.
  • Navigate to VLAN > VLAN Port.
  • Bind all uplink GE ports (GE0/1, GE0/2, GE0/3, GE0/4) to VLAN 100. Ensure the Uplink port is set to "Untag" mode.
  • Navigate to Uplink Port > Configuration.
  • Change the PVID for the uplink port to 100.

Step 4: Adding the ONU to the OLT

These steps are necessary if the ONU is not automatically detected ("Plug and Play" is enabled by default in "ONU AutoLearn"). If "Plug and Play" is disabled, manual addition is required.

  • Ensure the ONU is connected to the OLT via its PON ports and a splitter.
  • Check the ONU AuthList. If the ONU is automatically added, proceed to Step 5.
  • If not automatically added, go to ONU Configuration and select ONU Autofind.
  • Select the ONU you wish to add from the discovered list and click [Add].
  • Click [Submit] on the subsequent page.

The ONU should now be displayed and show an "Enable" status when connected correctly.

Step 5: ONU Configuration Selection

  • Click on the "ONU List" in the top-right corner of the OLT menu bar. If the "ONU List" button is not visible, navigate to ONU Configuration and click on ONU AuthList.
  • The list of active ONUs will be displayed. Select the ONU you want to configure (ensure its status is "Online") and click the [Config] button.

Step 6: Tcont and Gemport Configuration

Configure the "tcont", "gemport", "Service", "Service Port", and other parameters.

Tcont Setup

  • In the Tcont configuration section, add a new Tcont.
  • Example: Tcont ID: 2, Tcont Name: "test", DBA Profile Name: "default1".
  • Click [Commit].

Gemport Setup

  • In the Gemport configuration section, add a new Gemport.
  • Ensure the TcontID is selected as 1 (or the one previously created).
  • Example: Gemport ID: 2, Gemport Name: "test".
  • Click [Commit].

Step 7: Service and Service Port Configuration

Service Setup

  • In the Service configuration section, add a new Service.
  • Ensure Gemport ID 1 is selected.
  • Set VLAN Mode to "Tag".
  • For "VLAN List", enter the value 100 (the VLAN ID created in the OLT).
  • Click [Commit].

Service Port Setup

  • In the Service Port configuration section, add a new Service Port.
  • Example: Service Mode: "CVLAN", Service Port ID: 2, Gemport ID: 1.
  • Set User VLAN to 100 and Translate VLAN to 100 (as this example uses VLAN 100).
  • Click [Commit].

Step 8: ONU Ethernet Port (PortVLAN) Configuration

As the ONU is a SFU (Single Family Unit), its Ethernet ports need direct setup.

  • On the "PortVlan" page for the ONU, configure the following:
    • Mode: "Tag"
    • PortType: "Eth"
  • Configure each Ethernet port of the ONU:
    • For LAN port 1: Enter Port Id "1" and VLAN ID "100". Click [Commit].
    • For LAN port 2: Enter Port Id "2" and VLAN ID "100". Click [Commit].

Both ports are now configured to connect to the Internet.

Step 9: Save Configuration and Verification

  • Press [SAVE] in the top bar of the OLT to save the complete configuration.
  • The setup is now complete, and the ONU is connected to the Internet.

Verifying Internet Connectivity

  • Connect a PC to one of the ONU's LAN ports.
  • Configure the PC with a static IP address in the range of 192.168.1.x (e.g., 192.168.1.10). This is necessary because the PC might otherwise receive an IP from the router in the 192.168.110.x range.
  • Access the ONU's web interface by browsing to its default IP address: 192.168.1.1.
  • Note: To view and change the WAN port setup, log in as Administrator (not as User). Click on "Network" and select "WAN". Under "Connection Name", select the VLAN 100 connection to view its setup.
Models: ONU-10XG S -AX304P-2.5G, OLT and ONU in Default Configuration, ONU in Default Configuration, Default Configuration, Configuration
Setup guide for AirLive XG-XGS OLT and ONU-10XG(S)-1001-10G in Configuration Microsoft Word for Microsoft 365

Related Documents

Preview AirLive OLT and ONU Bridge Configuration Setup Guide
Comprehensive guide to setting up AirLive XGSPON OLT-2XGS and ONU devices (AX304P-2.5G, 1004-10G) in bridge mode for network connectivity.
Preview AirLive GPON OLT-121 and XPON ONU Setup Guide
Comprehensive setup guide for configuring AirLive GPON OLT-121 and XPON ONU devices in their default configuration. This document provides step-by-step instructions, network diagrams, and interface screenshots to facilitate the setup process for network administrators.
Preview AirLive GPON OLT-121 & XPON ONU Bridge Setup Guide
Step-by-step guide to setting up AirLive GPON OLT-121 and XPON 2.5G/1GE ONU Bridge, including WAN configuration and DHCP settings for optimal network connectivity.
Preview AirLive 2.5GE XPON ONU & XPON ONU-1GE User Manual
This user manual provides detailed instructions and configuration guidance for AirLive 2.5GE XPON ONU and XPON ONU-1GE devices, covering installation, setup, network features, and troubleshooting for reliable broadband connectivity.
Preview AirLive ONU-10XG(S)-1004-10G Quick Installation Guide
This guide provides instructions for installing and setting up the AirLive ONU-10XG(S)-1004-10G Optical Network Unit. It details indicator lights, interface descriptions, packing contents, and hardware installation procedures for both desktop and wall mounting.
Preview AirLive WEB-2TX Series 2.5G WebSmart Multi Gigabit Switches - Declaration of Conformity and Quick Setup Guide
Official Declaration of Conformity and Quick Setup Guide for AirLive WEB-2TX402, WEB-2TX501, WEB-2TX801, WEB-2TX1602, and WEB-2TX2402 2.5G WebSmart Multi Gigabit Switches with 10G SFP+.
Preview AirLive WEB-2TX801: 2.5Gbps Base-T WebSmart Multi Gigabit Switch
Detailed specifications and features of the AirLive WEB-2TX801, a 9-port 2.5Gbps Base-T WebSmart Multi Gigabit Switch with 8 x 2.5G RJ45 ports and 1 x 10G SFP+ uplink, designed for SMB and home networks.
Preview AirLive IP Camera Quick Installation Guide - Setup and Configuration
Comprehensive Quick Installation Guide for AirLive IP Cameras. Covers network setup, configuration, smart features, NVR integration, and troubleshooting. Visit www.airlive.com/download for software.