Keilton Basic RM51 Remote Controller for Fixture Sensor

تفصیل

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

ځانګړتیاوې

• د بریښنا کم مصرف.
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

مشخصات

د امر کولو معلومات

ماډل	تفصیل
د RM51.A0 معرفي کول	Basic Sensor Controller RM51
د RM51.A1 معرفي کول	Basic Sensor Controller RM51 With RML

Ordering Information – Accessories

ماډل	تفصیل
RML	Extended IR range for commissioning

ابعاد

د محصول لیبل

ریموټ لارښوونې

د یادښت حالت (کمیشن کول)
To begin commissioning, follow these steps:

1. Select a memory profile: A, B, C, D, or E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Daylight Harvesting (F Mode)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Additional Remote Functions

ON	وګرځي ON رڼاګانې
بند	وګرځي بند رڼاګانې
ټیسټ	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100% حساسیت: لوړ ، د ناستې وخت: 2s، Standby dim: 50% ولاړ وخت: 2s.
RESET	Trim= 100%, Sensitivity = لوړ, T1 = 5 دقیقې, Standby Dim = 30%, T2 = 60 دقیقې, Photocell = بند.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous ماښام
TRIM-LVEL	Set the Maximum brightness.
حساسیت	Set the motion sensitivity of the sensor ټیټ:50% / لوړ:100% بند: disable the motion detection function.
HOLDTIME	The duration that elapses without occupancy detection before transitioning to standby dim.
سټینډبای ډیم	Select any standby dim level.
تيارسئ وخت	Standby time, when the time is set to “∞”, the daylight detection function is activated.
عکس	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold ټیټ:5fc / لوړ:20fc, CAL: Collect the current visible light illuminance as the threshold, بند: disable PHOTOCELL function.
موډ	Default configuration parameters for modes A ته F.
لیږل	ترتیبات سینسر ته واستوئ.
DEFAULT موډ A	Trim= 100%, Sensitivity = ټیټ, T1 = 30 دقیقې, Standby Dim = 50%, T2 = ∞, Photocell = CAL.
ډیفالټ موډ ب	Trim= 100%, Sensitivity = ټیټ, T1 = 30 دقیقې, Standby Dim = 50%, T2 = 15 دقیقې, Photocell = CAL.
ډیفالټ موډ ج	Trim= 100%, Sensitivity = ټیټ, T1 = 30 دقیقې, Standby Dim = 50%, T2 = 15 دقیقې, Photocell = بند.
د ډیفالټ حالت	Trim= 50%, Sensitivity = ټیټ, T1 = 30 s, Standby Dim = 50%, T2 = 30 دقیقې, Photocell = CAL.
ډیفالټ موډ E	Manual Dimmer Mode, Trim 100%.
ډیفالټ موډ F	Daylight Harvesting, Trim= 50%, Sensitivity = ټیټ, T1 = 15 دقیقې.

موږ سره اړیکه ونیسئ

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 443-320-2233 (M-F 9 am-5 pm ET)
• E: support@autani.com

FAQS

How do I change the memory profile ترتیبات؟

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

اسناد / سرچینې

Keilton Basic RM51 Remote Controller for Fixture Sensor [pdf] د مالک لارښود RM51.A0, RM51.A1, RM51 Remote Controller for Fixture Sensor, RM51, Remote Controller for Fixture Sensor, for Fixture Sensor, Fixture Sensor

حوالې

• د کارن لارښود