1. پیژندنه
This manual provides comprehensive instructions for the HiLetgo PD/QC/AFC Fast Charge Decoy Trigger Board. This device is designed to trigger specific voltage outputs (5V, 9V, 12V, 15V, 20V) from compatible USB Type-C power sources that support PD2.0/PD3.0, QC2.0/QC3.0, and AFC fast charge protocols. Please read this manual thoroughly before use to ensure proper operation and safety.
2. د خوندیتوب معلومات
- Always ensure the power source is compatible with the supported fast charge protocols (PD2.0/PD3.0, QC2.0/QC3.0, AFC).
- د اعظمي حجم څخه ډیر مه کوئtage or current ratings of your connected device.
- د محصول حجم تایید کړئtage with a multimeter before connecting the board to any application circuit, especially after adjusting DIP switches.
- Avoid short-circuiting the output terminals (VCC and GND).
- Keep the board away from moisture, extreme temperatures, and static electricity.
- This product is intended for experienced users familiar with electronics.
3. محصول ختم شوview
The HiLetgo PD/QC/AFC Fast Charge Decoy Trigger Board is a compact module designed to negotiate specific fixed voltages from a USB Type-C power delivery source. It features a Type-C input port, DIP switches for voltage selection, and VCC/GND output pads.
Figure 1: Three HiLetgo PD/QC/AFC Fast Charge Decoy Trigger Boards. Each board is purple, rectangular, and features a USB Type-C port, a DIP switch, and VCC/GND output pads.
شکل 2: پورته view of a single HiLetgo PD/QC/AFC Fast Charge Decoy Trigger Board, showing the USB Type-C connector, the DIP switch with labels S1, S2, S3, and the VCC/GND output pads.
شکل 3: لاندې view of a single HiLetgo PD/QC/AFC Fast Charge Decoy Trigger Board, displaying the voltage selection table printed on the PCB. This table indicates the DIP switch settings for 5V, 9V, 12V, 15V, and 20V outputs.
4. مشخصات
- Supported Fast Charge Protocols: PD2.0/PD3.0, QC2.0/QC3.0, AFC
- Supported Output Voltages: 5V, 9V, 12V, 15V, 20V (fixed voltages only, voltage step not supported)
- د ننوتلو انٹرفیس: د USB ډول-C
- د تولید انٹرفیس: VCC and GND pads
- ابعاد: تقریبا ۹.۵ سانتي متره x ۷.۷ سانتي متره (۳.۷۵ انچه x ۳ انچه)
- خالص وزن: تقریبا ۷۰ ګرامه (۲.۵ اونس)
5. Setup and Voltage انتخاب
د محصول حجمtage is configured using the DIP switches located on the board. Refer to the voltage selection table printed on the back of the board (also shown in Figure 3) to set the desired voltage.
5.1 ټوکtage Selection Table
| د محصول Voltage | S1 | S2 | S3 |
|---|---|---|---|
| 5V | 0 | 0 | 0 |
| 9V | 1 | 0 | 0 |
| 12V | 0 | 1 | 0 |
| 15V | 1 | 1 | 0 |
| 20V | 0 | 0 | 1 |
Note: '0' typically means the switch is in the OFF position (down), and '1' means the switch is in the ON position (up). Always verify with the markings on your specific board.
5.2 د پیوستون مرحلې
- Set Desired Voltage: Before connecting power, adjust the DIP switches (S1, S2, S3) according to the table above for your desired output voltage.
- د بریښنا سرچینه وصل کړئ: Plug a compatible USB Type-C fast charger into the Type-C port on the decoy trigger board.
- د تولید حجم تایید کړئtage: Crucially, use a multimeter to measure the voltage between the VCC and GND pads on the board. This step confirms the board is outputting the expected voltage before connecting it to your application circuit.
- Connect to Application: یو ځل د voltage is verified, connect the VCC and GND pads to your target device or circuit.
6. عملیاتي لارښوونې
The decoy trigger board operates by negotiating a specific voltage from a fast charge power supply. Once the voltage is set via the DIP switches and power is applied, the board will attempt to trigger that voltage. The output will be available on the VCC and GND pads.
- Ensure the power supply can deliver the requested voltage and sufficient current for your application.
- If the power supply does not support the requested voltage, the board may default to a lower supported voltage (e.g., 5V) or fail to output any voltage. Always verify with a multimeter.
- د تولید حجم بدلولو لپارهtage, disconnect the power source, adjust the DIP switches, and then reconnect the power source. Always re-verify with a multimeter.
7. ستونزه حل کول
- نه والیtage محصول:
- Ensure the USB Type-C power source is functioning correctly and supports one of the specified fast charge protocols (PD2.0/PD3.0, QC2.0/QC3.0, AFC).
- Check if the Type-C cable is fully inserted and functional.
- Verify the DIP switch settings against the voltage selection table.
- د مختلف بریښنا سرچینې هڅه وکړئ.
- غلط حجمtage محصول:
- Double-check the DIP switch settings.
- The power source might not support the requested voltage. The board may output a lower default voltage.
- As noted in the product description, if the DIP switch is not adjusted according to the table, the module may output any one of the supported voltages. Ensure precise setting.
- Board Not Responding:
- Disconnect all power and connections, then reconnect carefully following the setup steps.
- د هر ډول لیدل شوي زیان لپاره تخته معاینه کړئ.
8. ساتنه
The HiLetgo PD/QC/AFC Fast Charge Decoy Trigger Board requires minimal maintenance.
- Keep the board clean and free from dust and debris. Use a soft, dry brush or compressed air if necessary.
- Store the board in a dry, cool environment when not in use.
- Avoid physical shock or excessive force on the components, especially the Type-C port and DIP switches.
9. تضمین او ملاتړ
For technical support or if you encounter any issues with your HiLetgo product, please contact the manufacturer directly.
- جوړونکی: HiLetgo
- Webسایټ: www.hiletgo.com
- د ملاتړ بریښنالیک: support@hiletgo.com
Please refer to the packaging or the official HiLetgo webد تضمین په اړه د تازه معلوماتو لپاره سایټ.
