د BFT Mitto B RCB02 R1 ریموټ کنټرول کارونکي لارښود

1. پیژندنه

This manual provides comprehensive instructions for the safe and effective use of your BFT Mitto B RCB02 R1 2-channel remote control. This device is designed for controlling compatible garage door openers and other automated systems operating on a 433.92 MHz rolling code frequency.

د بسته محتويات

• BFT Mitto B RCB02 R1 Remote Control
• Pre-installed Alkaline Battery
• د کارونکي لارښود (دا لاسوند)

2. د خوندیتوب معلومات

Please read and understand all safety instructions before operating the remote control. Failure to do so may result in damage to the device or connected systems.

• د ناڅاپي عملیاتو مخنیوي لپاره ریموټ کنټرول د ماشومانو له لاسرسي لرې وساتئ.
• Do not expose the remote control to water, excessive moisture, or extreme temperatures.
• Do not attempt to disassemble or modify the remote control beyond battery replacement.
• Ensure the area is clear before operating any automated system with the remote control.
• د ځایی مقرراتو سره سم کارول شوي بیټرۍ تصفیه کړئ.

3. محصول ختم شوview

The BFT Mitto B RCB02 R1 is a compact and ergonomic 2-channel remote control. It features two distinct buttons for operating different functions or devices.

شکل 3.1: مخکی view of the BFT Mitto B RCB02 R1 remote control, showing the two control buttons and the BFT logo.

شکل 3.2: مخکی او شاته view of the BFT Mitto B RCB02 R1 remote control, illustrating the overall design and the screw for accessing the battery compartment.

اجزا

• د کنټرول تڼۍ: Two distinct buttons for transmitting signals.
• د LED شاخص: A small light that illuminates when a button is pressed, indicating signal transmission.
• د بیټرۍ کڅوړه: Located on the back, secured by a screw.
• د کیرینګ لوپ: For attaching to a keyring or lanyard.

4. ترتیب کول

۳.۲. د بیټرۍ نصبول (که مخکې له مخکې نصب شوي نه وي)

The BFT Mitto B RCB02 R1 remote control comes with a pre-installed alkaline battery. If replacement is needed, follow these steps:

1. Locate the small screw on the back of the remote control.
2. Using a small Phillips head screwdriver, carefully unscrew and remove the screw.
3. Gently pry open the two halves of the remote control casing.


شکل 4.1: داخلي view of the remote control, showing the battery and circuit board.

4. Carefully remove the old battery, noting its polarity (+/-).
5. Insert a new 12V alkaline battery (e.g., A23 or 23A type) with the correct polarity.
6. د ج دوه نیمې برخې سره برابر کړئasing and gently press them together until they click into place.
7. Re-insert and tighten the screw to secure the casing.

4.2. د ریموټ کنټرول برنامه کول

The BFT Mitto B RCB02 R1 uses a rolling code system and must be programmed to your specific receiver. The programming procedure varies depending on the model of your BFT receiver (e.g., garage door opener, gate opener). Refer to the instruction manual of your BFT receiver for detailed programming steps. Generally, the process involves:

1. Accessing the programming mode on your BFT receiver (often by pressing a "PROG" or "MEMO" button).
2. Pressing a button on the new remote control within a specific timeframe.
3. Confirming successful programming (e.g., LED on receiver flashes or changes color).

یادونه: If you are replacing an existing BFT Mitto remote, some receivers may support cloning from an already programmed remote. Consult your receiver's manual for this advanced feature.

5. عملیاتي لارښوونې

Once programmed, operating the BFT Mitto B RCB02 R1 remote control is straightforward.

1. Ensure you are within the operational range of your receiver (up to 150 meters in open air, actual range may vary due to obstacles).
2. Point the remote control towards the receiver (if line-of-sight is required by your system).
3. Press and hold the desired button (Button 1 or Button 2) for approximately 1-2 seconds. The LED indicator on the remote will illuminate during transmission.
4. Release the button once the connected device (e.g., garage door) begins to operate.

Each button can be programmed to control a different device or function, depending on your receiver's capabilities.

6. ساتنه

6.1. د بیټرۍ بدلول

The remote control is powered by a 12V alkaline battery (e.g., A23 or 23A). The battery life will vary depending on usage. If the LED indicator on the remote control becomes dim or the remote's range decreases significantly, it is likely time to replace the battery. Refer to Section 4.1 for detailed battery replacement instructions.

6.2. پاکول

To clean the remote control, wipe it gently with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.

7. ستونزه حل کول

8. مشخصات

9. تضمین او ملاتړ

For warranty information and technical support, please contact the retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.

For further assistance or inquiries, please refer to the contact information provided with your purchase or visit the official BFT webسایټ