Ryobi RAG 800-125G Electric Angle Grinder User Manual

۱.۱. د خوندیتوب مهم معلومات

تل د دې بریښنا وسیلې سره چمتو شوي ټول خوندیتوب اخطارونه، لارښوونې، انځورونه او مشخصات ولولئ او پوه شئ. د لاندې لیست شوي ټولو لارښوونو تعقیبولو کې پاتې راتلل ممکن د بریښنا شاک، اور، او/یا جدي ټپي کیدو لامل شي. د راتلونکي حوالې لپاره ټول اخطارونه او لارښوونې خوندي کړئ.

• د سترګو د ساتنې جامې: Always wear appropriate eye protection, such as safety goggles or a face shield, to protect against flying debris.
• د اورېدو محافظت واغوندئ: Prolonged exposure to noise from grinding operations can cause hearing damage.
• Use Proper Guards: Ensure the guard is correctly positioned and securely fastened before operation.
• ټینګ گرفت وساتئ: Always hold the angle grinder firmly with both hands during operation.
• Inspect Workpiece: Ensure the workpiece is stable and secured to prevent movement during operation.
• د زیانونو لپاره چک کول: Before each use, inspect the tool for any damage, loose parts, or worn components. Do not operate a damaged tool.
• کله چې په استعمال کې نه وي نو پلګ کړئ: د هر ډول سمون کولو، لوازمو بدلولو، یا د وسیلې ذخیره کولو دمخه وسیله د بریښنا سرچینې څخه جلا کړئ.

2. ترتیب کول

Before operating your Ryobi RAG 800-125G Electric Angle Grinder, ensure it is properly set up and all components are securely attached.

2.1 پیک کول

Carefully remove the angle grinder and all accessories from the packaging. Inspect for any shipping damage. Retain packaging for future storage or transport.

۴.۱ د غاړې لاستی نښلول

The side handle can be adjusted to two positions for optimal control and comfort, depending on the application and user preference.

1. د ګرینډر د ګیر هاوسنګ په دواړو خواوو کې تار شوي سوري ومومئ.
2. Screw the side handle firmly into the desired position. Ensure it is tightened securely to prevent movement during operation.

2.3 Installing/Changing Grinding Wheel

Always ensure the tool is unplugged from the power source before installing or changing any accessories.

1. فشار ورکړئ او ونیسئ shaft locking button to prevent the spindle from rotating.
2. Using the provided wrench, loosen and remove the outer flange nut by turning it counter-clockwise.
3. Place the desired grinding or cutting disc onto the inner flange, ensuring it sits flush. The disc diameter should be 125 mm and the bore 22 mm.
4. Replace the outer flange nut and tighten it clockwise with the wrench while holding the shaft locking button. Do not overtighten.

۴.۳ د ساتونکو تنظیم کول

The guard protects against sparks and debris. Adjust it to provide maximum protection for your specific task.

• Loosen the guard's locking screw or lever.
• Rotate the guard to the position that best shields you from sparks and debris.
• Tighten the locking screw or lever securely. Never operate the grinder without the guard properly installed.

Figure 1: Ryobi RAG 800-125G Angle Grinder showing the main body, side handle, and protective guard. The shaft locking button is visible near the spindle.

3. عملیاتي لارښوونې

Follow these guidelines for safe and effective operation of your angle grinder.

۵.۱ د وسیلې پیل کول

The Ryobi RAG 800-125G features a LLO (Lock-Off) system for protection against accidental starts in the event of a power failure. This means if power is interrupted, the tool will not restart automatically when power is restored.

1. ډاډ ترلاسه کړئ چې وسیله په مناسب بریښنا رسۍ کې ولګول شوې ده.
2. To start, press the safety lock-off button (if present) and then depress the trigger switch.
3. د ودرولو لپاره، د ټریګر سویچ خوشې کړئ.

3.2 Proper Grip and Posture

Always maintain a firm grip with both hands on the main handle and the side handle. Stand in a balanced position, keeping your body clear of the rotating disc and potential kickback paths.

۵.۲ د پیسولو او پرې کولو تخنیکونه

Allow the disc to reach full speed before contacting the workpiece. Apply light, even pressure. Avoid forcing the tool, as this can lead to kickback or damage to the disc and tool.

Figure 2: Proper technique for cutting a stone slab with the Ryobi RAG 800-125G Angle Grinder. Note the firm two-hand grip and appropriate safety glasses.

Figure 3: Demonstrating metal cutting with the Ryobi RAG 800-125G Angle Grinder. Sparks are a normal byproduct of this operation; ensure proper PPE and clear surroundings.

4. ساتنه

Regular maintenance ensures the longevity and safe operation of your angle grinder. Always unplug the tool before performing any maintenance.

4.1 پاکول

Keep the ventilation openings clear and free from dust and debris. Use a soft brush or compressed air to clean the tool. Do not use water or chemical cleaners.

۶.۲ د ډیسک معاینه او ځای په ځای کول

Regularly inspect grinding and cutting discs for wear, cracks, or damage. Replace worn or damaged discs immediately. Never use a disc that is chipped or cracked.

4.3 ذخیره کول

Store the angle grinder in a dry, secure location out of reach of children. Ensure the power cord is neatly coiled and not kinked.

5. ستونزه حل کول

If you encounter issues with your Ryobi RAG 800-125G, refer to the following common problems and solutions.

If the problem persists after attempting these solutions, please contact Ryobi customer support or an authorized service center.

6. مشخصات

Technical data for the Ryobi RAG 800-125G Electric Angle Grinder.

7. تضمین او ملاتړ

For warranty information, service, or technical support, please refer to the warranty card included with your product or visit the official Ryobi webسایټ. د تضمین ادعاوو لپاره د پیرود ثبوت وساتئ.

د ریوبي رسمي Webسایټ: www.ryobitools.com