1. پیژندنه
This manual provides essential information for the proper installation, function, and maintenance of the Geberit G366887161 HDPE Straight Connector. This product is designed for use in waste fitting applications, specifically for connecting to appliances with a horizontal outlet using 3.54-inch (90 mm) push-fit piping.
The Geberit G366887161 is a durable HDPE (High-Density Polyethylene) straight connector featuring a ring seal socket, ensuring a secure and reliable connection within your plumbing system.
2. محصول ختم شوview او اجزا
The Geberit G366887161 is a single-piece straight connector. Key features include:
- مواد: لوړ کثافت پولیټین (HDPE)
- د نښلونکي ډول: Straight with ring seal socket
- Pipe Diameter Compatibility: Designed for 3.54 inches (90 mm) push-fit piping
- غوښتنلیک: Suitable for appliances with horizontal outlets
- اوږدوالی: تقریبا 12 انچه
شکل 1: Technical drawing illustrating the dimensions of the Geberit HDPE Straight Connector. The drawing shows the main diameter 'd', the socket diameter 'd1', the overall diameter 'D', and various lengths 'K', 'I', and 'L' for installation reference.
۵. نصب کول (تنظیم)
Follow these steps for proper installation of the Geberit G366887161 HDPE Straight Connector:
- چمتووالی: Ensure the appliance outlet and the connecting pipe are clean, free from debris, and properly aligned. Verify that the pipe diameter is 3.54 inches (90 mm) for a secure push-fit connection.
- Lubrication (Optional but Recommended): Apply a suitable lubricant (e.g., silicone grease) to the ring seal and the end of the pipe to facilitate easier insertion and ensure a watertight seal.
- اضافه کول: Carefully push the straight connector onto the appliance's horizontal outlet. Ensure it is fully seated and the ring seal is not twisted or displaced.
- د پایپ پیوستون: Insert the 3.54-inch (90 mm) waste pipe into the socket end of the straight connector. Apply firm, even pressure until the pipe is fully engaged with the ring seal.
- تایید: Visually inspect the connection points to ensure there are no gaps and the connector is securely in place.
- د لیک ازموینه: After installation, run water through the system and check for any leaks around the connection points. Address any leaks immediately by re-seating the connection or checking for damage to the seal or pipe.
یادونه: Always consult local plumbing codes and regulations before beginning any installation. If you are unsure about any step, it is recommended to consult a qualified plumber.
۴. فعالیت او کارول
Once correctly installed, the Geberit G366887161 HDPE Straight Connector provides a reliable and durable connection for waste water drainage. Its primary function is to:
- Connect Waste Pipes: Facilitate the connection of a 3.54-inch (90 mm) waste pipe to an appliance with a horizontal outlet.
- Ensure Watertight Seal: The integrated ring seal socket creates a secure, leak-proof joint for efficient waste removal.
- Provide Durability: Made from HDPE, the connector is resistant to corrosion, chemicals, and temperature fluctuations commonly found in waste systems.
This connector is designed for internal plumbing applications and should not be exposed to direct sunlight or extreme external environmental conditions unless specifically rated for such use.
5. ساتنه
The Geberit G366887161 HDPE Straight Connector requires minimal maintenance due to its robust material and design. However, periodic inspection is recommended:
- بصری معاینه: Periodically check the connection points for any signs of leaks, cracks, or physical damage.
- پاکول: If accessible, clean the exterior of the connector with mild soap and water. Avoid harsh abrasive cleaners or solvents that could damage the HDPE material.
- د مهر بشپړتیا: While the ring seal is designed for long-term performance, if any persistent leaks occur, the seal may need inspection or replacement by a professional.
6. ستونزه حل کول
Most issues related to the straight connector are installation-related. Here are common problems and their solutions:
| ستونزه | احتمالي لامل | د حل لاره |
|---|---|---|
| د اتصال په نقطو کې لیکونه |
|
|
| Difficulty inserting pipe/connector |
|
|
If troubleshooting steps do not resolve the issue, contact Geberit customer support or a qualified plumbing professional.
7. مشخصات
| د ماډل شمیره | 366.887.16.1 |
| برانډ | Geberit |
| مواد | HDPE (د لوړ کثافت پالیتیلین) |
| د نښلونکي ډول | Straight with Socket |
| د پایپ مطابقت | 3.54 inches (90 mm) push-fit piping |
| نومیالی تار اندازه | DN 90 |
| ابعاد (L x W x H) | Approximately 1.97 x 0.39 x 0.39 inches (Product dimensions, not overall length) |
| په ټولیزه توګه اوږدوالی | تقریبا 12 انچه |
| د توکي وزن | 0.01 اونس |
| رنګ | نه ختمیدونکی |
| شاملې برخې | Product Only (1 piece) |
8. د تضمین معلومات
The Geberit G366887161 HDPE Straight Connector is covered under Geberit's د 1 کلن محدود تضمیندا تضمین د عادي استعمال او خدماتو لاندې د موادو او کاریګرۍ نیمګړتیاوې پوښي.
For specific terms and conditions of the warranty, please refer to the official Geberit warranty documentation or contact Geberit customer support.
۱۰. ملاتړ او اړیکه
For further assistance, technical inquiries, or warranty claims regarding your Geberit G366887161 HDPE Straight Connector, please contact Geberit customer support through their official webسایټ یا ټاکل شوي خدماتو چینلونه.
کله چې د ملاتړ سره اړیکه ونیسئ، مهرباني وکړئ د خپل محصول ماډل شمیره (۱۷۰۶۳) او د پیرود معلومات په اسانۍ سره شتون ولرئ.
