د لارښوونې لارښود

1. پیژندنه

This manual provides essential information for the proper installation, operation, and maintenance of your Nice ER12 Double Sealed Ball Bearing. Adhering to these guidelines will ensure optimal performance, extend the lifespan of the bearing, and maintain safety.

The Nice ER12 is a single-row radial ball bearing designed for applications requiring support for medium radial loads and operating speeds up to 5000 RPM. It features an extended inner ring with set screws for improved shaft support and synthetic rubber seals with steel shields to protect against contaminants.

2. محصول ختم شوview

The Nice ER12 ball bearing is constructed from through-hardened ASTM International 52100 bearing quality steel, ensuring optimum wear resistance. Its design incorporates a nylon cage that evenly spaces the balls, contributing to reduced friction, vibration, and noise during operation.

کلیدي ځانګړتیاوې عبارت دي له:

• Single-row radial ball bearing for medium radial loads and speeds up to 5000 RPM.
• Extended inner ring with set screws for enhanced shaft support, eliminating the need for location spacers.
• Nylon cage for reduced friction, vibration, and noise.
• Through-hardened 52100 bearing quality steel for superior wear resistance.
• Synthetic rubber seals with steel shields on both sides, riding in a labyrinth groove to retain lubricant and exclude contaminants.

Figure 2.1: Three-quarter view of the Nice ER12 Double Sealed Ball Bearing, showing the extended inner ring and seals.

شکل 2.2: اړخ view of the Nice ER12 Double Sealed Ball Bearing, highlighting the extended inner ring with set screws and the double seals.

3. مشخصات

4. ترتیب او نصب کول

Proper installation is crucial for the longevity and performance of the bearing. Always ensure a clean working environment to prevent contamination.

1. چمتووالی: Clean the shaft and housing thoroughly. Ensure there are no burrs, rust, or foreign particles.
2. Shaft Fit: The ER12 bearing features an extended inner ring with set screws. Slide the bearing onto the shaft. The fit should be snug but not excessively tight.
3. خوندي کول: Once positioned, tighten the set screws on the extended inner ring to secure the bearing firmly to the shaft. Ensure even tightening to prevent misalignment.
4. سمون: Verify that the bearing is properly aligned with the housing and shaft to prevent premature wear and excessive loads.
5. غوړول: This bearing is pre-lubricated and double-sealed at the factory. No initial lubrication is required.

Caution: Never use excessive force during installation, as this can damage the bearing components, especially the seals and raceways.

5. د عملیاتو لارښوونې

The Nice ER12 bearing is designed for specific operating conditions. Adhering to these guidelines will maximize its lifespan and efficiency.

• سرعت: The bearing is rated for speeds up to 5000 RPM. Exceeding this limit can lead to overheating and premature failure.
• بار It is designed to support medium radial loads. Avoid applying excessive axial or shock loads beyond its design capacity.
• دحرارت درجه: Operate within the recommended temperature range for the bearing's lubricant. Extreme temperatures can degrade the lubricant and bearing material.
• چاپیریال: While double-sealed, prolonged exposure to highly abrasive dust, corrosive chemicals, or excessive moisture should be minimized.

6. ساتنه

Regular maintenance ensures the continued reliable operation of your ER12 bearing.

• غوړول: The ER12 bearing is double-sealed and pre-lubricated for life under normal operating conditions. Re-lubrication ports are not present, and opening the seals is not recommended as it can compromise their integrity and introduce contaminants.
• معاینه: Periodically inspect the bearing for signs of wear, damage, or unusual noise/vibration. Check the integrity of the seals for any cracks or leaks.
• پاکول: Keep the area around the bearing clean to prevent accumulation of dirt and debris that could potentially compromise the seals.
• ذخیره کول: If storing spare bearings, keep them in their original packaging in a cool, dry, and clean environment to prevent corrosion and damage.

7. ستونزه حل کول

If you encounter issues with your ER12 bearing, consider the following common problems and potential solutions:

If troubleshooting steps do not resolve the issue, it may indicate a need for professional assessment or replacement of the bearing.

8. تضمین او ملاتړ

The Nice ER12 Ball Bearing is manufactured by RBC Bearings, a company founded in 1919 and headquartered in Oxford, CT. RBC Bearings adheres to International Organization for Standardization (ISO) standards 9001:2008 and ISO/TS 16949:2009, ensuring high-quality manufacturing processes.

For specific warranty information or technical support, please refer to the official RBC Bearings website or contact their customer service directly. Details regarding product warranty terms and conditions are typically provided at the point of purchase or on the manufacturer's official documentation.

Note: This manual provides general guidance. Always consult specific application requirements and professional engineering advice when necessary.