Yinuogo YNG808 Garage Door Remote Control User Manual

پیژندنه

This manual provides instructions for the Yinuogo YNG808 Garage Door Remote Control. Please read this manual carefully before use to ensure proper operation and to avoid damage to the device or property.

The YNG808 is a 2-button rolling code remote control operating at 433.92MHz, designed for compatibility with specific garage door openers and radio receivers, particularly those from the NICE FLORS, FLO2RS, FLO4RS, NICE ERA FLO2RE, FLO4RE, ON2E, ON4E, FLORE, and NICE INTI2 series.

Image: Yinuogo YNG808 Garage Door Remote Control with included visor clip.

مهم یادښتونه

• Access to Receiver Required: This remote control cannot be cloned directly from another remote. Programming requires direct access to your garage door opener's receiver or the radio receiver unit. Please ensure you have access to your receiver/opener before attempting to program.
• مطابقت: This remote is specifically designed for certain NICE brand systems (FLORS, FLO2RS, FLO4RS, NICE ERA FLO2RE, FLO4RE, ON2E, ON4E, FLORE, NICE INTI2). It is not compatible with other brands. Your existing remote control's brand and frequency must match the specifications of the YNG808 (433.92MHz, Rolling Code) for it to function correctly.

Image: The YNG808 remote control is a 100% replacement for various NICE brand remotes, as illustrated by the different remote shapes.

د بسته محتويات

د خپل کڅوړې د پرانیستلو پر مهال، مهرباني وکړئ ډاډ ترلاسه کړئ چې لاندې ټول توکي پکې شامل دي:

• YNG808 Remote Control
• Battery (pre-installed or included separately)
• English User Manual (this document, content derived from د PDF لارښود)
• Keychain / Visor Clip

Image: Components of the YNG808 remote control package, showing the remote, clip, and an open view of the remote's internal structure.

تنظیم او برنامه کول

The YNG808 remote control is programmed directly to your garage door opener's receiver. Follow these steps carefully:

د ریموټ کنټرول پروګرام کول:

1. د زده کړې حالت فعال کړئ: Briefly press and hold the learning button on your radio receiver or door opener. The LED indicator on the operator will turn on, indicating it's in learning mode.
2. د لیږد کوډ: While the operator's LED is on, press the desired button on your new YNG808 remote control. The receiver's LED will flash and then remain steadily lit.
3. د پروګرام کولو تایید: Continue holding the button on the remote until the receiver's LED turns off. This confirms that the remote has been successfully coded to the operator.

Image: Visual guide for programming the remote control to an OX2 receiver. Step 1 shows the OX2 receiver with LED and button. Step 2 illustrates pressing the receiver button once (x1) and then pressing the remote button until the receiver LED flashes and stays on, then turns off. Step 3 shows a similar process for a second output (x2).

Deleting a Remote Control Code:

To remove a previously programmed remote control from the receiver's memory:

1. Enter Delete Mode: Press and hold the learning button on the receiver. The receiver's LED will turn on.
2. Confirm Deletion: Continue holding the learning button. The receiver's LED will flash multiple times. Release the button when the LED flashes for the third time. This action will delete the stored code for that remote.

عملیاتي لارښوونې

Once programmed, the YNG808 remote control is ready for use.

• پرانیستل / تړل: Press the programmed button on the remote control to activate your garage door opener. Pressing it again will typically stop or reverse the door's movement, depending on your opener's settings.
• سلسله: The remote has a working range of approximately 30m-50m, depending on environmental factors and obstacles.

Image: The YNG808 remote control with its clip, conveniently attached to a car's sun visor for easy access.

ساتنه

• د بیټرۍ بدلول: The remote control includes a battery. If the remote's range decreases significantly or it stops responding, the battery may need replacement. To replace, carefully open the remote casing and insert a new battery of the same type.
• پاکول: Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• ذخیره کول: ریموټ په وچ ځای کې وساتئ، د سختې تودوخې او مستقیم لمر وړانګو څخه لرې.

د ستونزو حل کول

• د پروګرام کولو وروسته ریموټ کار نه کوي:
  • Ensure you have access to the receiver and followed the programming steps precisely.
  • Verify that your garage door opener's brand and frequency are compatible with the YNG808 (433.92MHz, Rolling Code).
  • بیټرۍ په ریموټ کنټرول کې چیک کړئ.
  • Try reprogramming the remote.
• د عملیاتي حد کم شوی:
  • بیټرۍ په ریموټ کنټرول کې ځای په ځای کړئ.
  • Ensure there are no new obstructions between the remote and the receiver.
  • په سیمه کې د راډیو مداخلې سرچینې وګورئ.
• Door opens/closes unexpectedly:
  • This is unlikely with rolling code technology, but if it occurs, delete all codes from the receiver and reprogram only your desired remotes.

مشخصات

د کارن لارښوونې

• When replacing a lost remote, remember to delete all existing codes from your receiver first, then program only the new remote(s) to ensure security.
• Always keep a spare working remote or know how to manually operate your garage door in case of remote failure or battery depletion.

یادونه: د کارونکي کوم ځانګړی نوم نشتهviews or Q&A were provided to generate more detailed user tips.

تضمین او ملاتړ

The Yinuogo YNG808 remote control comes with a 1-year warranty from the store. For any issues or support inquiries, please contact the seller directly.

For additional information or assistance, please refer to the official product page or contact Yinuogo customer service.