Universal LED Signal Alarm Light Strobe Flashing Light User Manual

1. د خوندیتوب لارښوونې

• For security, please read this user manual carefully before initial operation.
• Ensure the power is off before connecting. This product is produced without an internal fuse.
• This system must not endanger life or property during running failure, and all security risks must be eliminated.

2. مشخصات

3. محصول ختم شوview & برخی

The Universal LED Signal Alarm Light is designed for various outdoor applications, featuring a robust and versatile design.

• ملټي والtage مطابقت: Operates on 12V, 24V, or 220V AC/DC, making it suitable for a wide range of systems.
• انتن: Includes an antenna to extend the effective control distance of your RF controller.
• دوامدار او د هوا ضد: Constructed from plastic material with an IP54 rating, ensuring it is waterproof and dustproof for outdoor use.
• Super Bright 360° LED: Provides high visibility with a 360-degree LED light source.

4. نصب کول

1. خلاص کړئ: کڅوړه پرانیزئ او ایل یې واخلئamp and all accessories. Remove the antenna by rotating it anti-clockwise.
2. د نښه کولو سوري: Use the fixing holes of the bracket to mark two holes on the wall for mounting.
3. سوراخونه: Drill two 6mm diameter holes for the expansion plugs and one 10mm diameter hole for the wires. Insert the expansion plugs into the 6mm holes.
4. د لارې تارونه: Pass the power wire and antenna wire through the cable holes in the holder.
5. ماونټ هولډر: Fix the holder to the wall using the provided 4mm*30mm self-tapping screws.
6. د تارونو نښلول: Connect the power wire to Terminal 1 (12-265VAC/DC input) and the antenna wire to Terminal 2 (for RF controller extension).
7. خوندي پوښ: Place the cover back, ensuring it is fastened securely to the bottom base without any gaps. Screw the antenna up clockwise until tight.
8. لورينه: Always install the holder and lamp upright to the ground. Horizontal installation may allow rain to enter the lamp and damage the circuit board.

د تار لګولو خبرتیا:

• Terminal 1 is for connecting the power input; working voltage is 12-265VAC/DC.
• Terminal 2 is for connecting the antenna of the RF controller to extend the effective working distance.

5. عملیات

یوځل چې د ایلamp is powered on, the LED will start flashing at 1Hz (default setting).

• Flashing/Constant On Mode: The switch 'sW1' controls the lamp's mode.
• If the CAP short-connects the 2 pins, the lamp operates in flashing mode.
• If the CAP is removed from the 2 pins, the lamp operates in constant 'on' mode.
• لوړ والیtagخبرداری: Be careful! The entire circuit board contains high-voltage components. Always ensure the power is off before opening the cover or making any adjustments.

۵.۲. د کارونې سناریوګانې

This versatile signal light is suitable for a wide range of applications, enhancing safety and visibility:

• د ګراج دروازې
• Electronic gates
• Barrier gates
• سلایډ دروازې
• اتومات دروازې
• Rolling doors and shutters
• General electrical appliances and home automation systems (e.g., lights, alarm systems, access control systems)

7. د بسته محتويات

ستاسو کڅوړه باید لاندې توکي ولري:

• 1x Flash Lamp
• 1x انتن
• 2x پیچ
• ۱x د انګلیسي ژبې کارن لارښود

8. د کارن لارښوونې

• خوندي نصب کول: تل ډاډ ترلاسه کړئ چې lamp is securely mounted to a stable surface to prevent accidental dislodgement, especially in outdoor environments.
• د تارونو تصدیق کول: Double-check all electrical connections before powering on the device to ensure correct voltage and polarity, preventing damage to the lamp or connected system.
• د انتن ځای پرځای کول: For optimal range, position the antenna away from large metal objects or other sources of interference.

9. ډیری پوښتل شوي پوښتنې (FAQ)

پوښتنه: زه څنګه د l سره وصل کړم؟amp to my gate motor?

A: Terminal 1 on the lamp is for power input (12-265VAC/DC). You will need to connect this to the appropriate power output terminals on your gate motor control board. Consult your gate motor's manual for specific wiring instructions. Terminal 2 is for the RF controller antenna.

Q: Can you provide a detailed wiring diagram?

A: A general installation diagram is provided in Section 4 of this manual. For specific wiring to your gate opener or automation system, please refer to the wiring diagram provided with your gate opener's control board, as connections can vary between models. Always ensure power is off before making connections.

10. تضمین او ملاتړ

This product is manufactured to high-quality standards. For any technical assistance or warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.