PROSCEND-M330-Series-Industrial-Cellular-Router-logo

PROSCEND M330 Series Industrial Cellular Router

PROSCEND-M330-Series-Industrial-Cellular-Router-product-image

M330 Series Industrial Cellular Router Quick Installation Guide

Version: 1.00

Install the SIM Card
  • STEP 1: Before inserting or removing the SIM card, ensure that the power has been turned off, or the power connector has been removed from the M330 Cellular Router.
  • STEP 2: Using a screwdriver to remove the metal protective cover first, insert the SIM card into the card slot. The cut-off edge of the SIM card on SIM slot is to the left.
  • STEP 3: Push the SIM card and lightly press it to lock into the slot.
  • STEP 4: Remove the SIM card, lightly press it and it will pop out of the slot.

PROSCEND-M330-Series-Industrial-Cellular-Router-01

NOTE: 

  • Please use the industrial SIM card operating from -40°C to +105°C to ensure proper cellular router operation.
LED Indicators

The following table explains the LED indicators on the front panel.

LED Off On Slow Fast Heartbeat
FN N/A VPN

connected

Internet

connected

Booting Wi-Fi

Connected

RSSI No

signal

High signal Medium

signal

Low

signal

WPS

Processing

PWR Power down Power up N/A N/A N/A
WPS and Reset Button
Function Operation
WPS Processing Press the button less than 5 seconds.
Reset Press the button for 5-10 seconds.
Reset to default setting Press the button for more than 10 seconds.

Connecting I/O Ports

There are four terminals on the terminal block with two terminals used for digital input and two terminals used for digital output.

PROSCEND-M330-Series-Industrial-Cellular-Router-02

Pin Description
DI Digital Input
DI_GND
DO Digital Output
DO_GND
  • DI: Low (+0 to +5V) / High (+8 to +40V)
  • DO: Open Collect (maximum 30V/300mA)

LED Indicators of Ethernet Port

There is one LED indicator for LAN port and WAN port.

PROSCEND-M330-Series-Industrial-Cellular-Router-03

LED Blinking On Off
Green

(Link / ACT)

Data Transmitting LINK UP LINK DOWN

RS-232 and RS-485 pinouts 

PROSCEND-M330-Series-Industrial-Cellular-Router-04

NOTE:

  • RS-232 and RS-485 share the signal pins “TXD(D+)”, “RXD(D-)” and common ground pin “GND”.

RS-232 (Applicable for M330-W) 

Pin Signal Direction
TXD Transmit Data Output
RXD Receive Data Input
GND Signal Ground

RS-485 (Applicable for M330-W5) 

Pin Description
D + Serial Port, Data+ (A) wire
D – Serial Port, Data- (B) wire
GND Signal Ground

PROSCEND-M330-Series-Industrial-Cellular-Router-05

Connecting the Power Supply

Powering the M330 Cellular Router is by either terminal block or a DC jack.

  • V+, V- pints of the terminal block on the front panel.
  • The power input voltage range is 8 ~48VDC.
    PROSCEND-M330-Series-Industrial-Cellular-Router-06
  • One DC Jack is on the right panel.
  • The power input voltage is 12 VDC.
    PROSCEND-M330-Series-Industrial-Cellular-Router-07

Antenna Installation

Three SMA connectors placed on the left panel are for connecting to external LTE and GPS antennas.

  • MAIN: for LTE Transmit and Receive
  • GPS: for GPS
  • AUX: for optional LTE Receive for better downstream speed

PROSCEND-M330-Series-Industrial-Cellular-Router-08

Two RP-SMA connectors placed on the right panel are for connecting to external Wi-Fi antennas.

PROSCEND-M330-Series-Industrial-Cellular-Router-09

DIN-rail and Wall Mounting

Din-rail

  • STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side of the device.
  • STEP 2: Hook the unit onto the DIN-rail.
  • STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in place.

NOTE: 

  • Two screw types are flat head M3 x 4 mm.
Wall Mounting
  • STEP 1: At the bottom side of the device, use two screws to install the wall bracket.
    NOTE: 
    • Each screw type is flat head M3 x 4mm.
  • STEP 2: Hang the device on the wall with the installed wall bracket.

Setup

  1. Access the Web Configurator
    1. Type the default URL http://192.168.1.1 in your web browser.
    2. In the login page, enter the default username root and the default password 2wsx#EDC and then click the Login button.
  2. Change the Password
    Go to the Management -> Administration and enter the desired New Password and then scroll down the page and click the Apply button.
Wi-Fi Connection
  1. SSID
    The default SSID is a string of characters (the MAC address of the device).
  2. Password
    1. The default Wi-Fi password is 12345678.
    2. Go to WiFi -> WiFi Config and change the default SSID and passphrase, then click Apply button

NOTE 

PROSCEND-M330-Series-Industrial-Cellular-Router-10

P/N: 604040000083

Proscend Communications Inc.
All rights reserved.

www.proscend.com

Documents / Resources

PROSCEND M330 Series Industrial Cellular Router [pdf] Installation Guide
M330 Series Industrial Cellular Router, M330 Series, Industrial Cellular Router, Cellular Router, Router
PROSCEND M330 Series Industrial Cellular Router [pdf] Installation Guide
M330 Series Industrial Cellular Router, M330 Series, Industrial Cellular Router, Cellular Router, Router

References

Leave a comment

Your email address will not be published. Required fields are marked *