PROAIM ST-EQZR-00 2-Axis Equalizer
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed below. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permitted by the applicable copyright statutes or in writing by the Publisher.
2-Axis Equalizer Setup
- Firstly, take ba in Slider and loosen the screws from the bottom. Remove the part with index markings.
- Mount this part on the handlebar grip and fix it with provided screws.
- Then take a small Slider and Rail System. Join both of these together via the provided screws, as shown.
- Loosen and remove one of the rubber end-stoppers from the big Slider. Insert the above joined small Slider setup onto the big Slider.
- Now again fix this part on the big Slider. After fixing, it will look as shown in the image.
- Tighten back the rubber end-stopper on a big Slider to secure the Rail System.
- Now loosen and remove one of the rubber end-stoppers from the small Slider.
- Insert the Rail System with Loop onto the Slider and tighten back the stopper to secure it.
Top Handle Assembly
The Top Handle Grip works well with DJI Ronin/M/MX and DJI RONIN 2 (R2) Gimbals.
NOTE: If you wish to change your Gimbal from free fly MOVI to DJI Ronin, then change the Handle Grip System by removing the bottom part with index markings.
- Take the Top Handle Grip, loosen, and remove the screw. Mount the part with index markings onto the Grip and fix it with screws.
- Now fix this part on the bottom of the big Slider and tighten the screws accurately.
- NOTE: There are 2 sizes of Adapter Rings provided with this gear – 25mm & 22mm. You can very easily change Adapter Rings from Grips as per requirement.
- Therefore, the grip can clamp onto 22mm, 25mm, 3, and 0mm tubes.
- Loosen all the screws on the bottom of the Top Handle Grip, to change Adapter Ring.
- Pull one section up to take out the Ring.
- Insert the other side of the Ring and tighten the screws back.
NOTE: Similarly follow the mentioned above steps to change the Adapter Ring of the Handle Bar Grip.
To Increase the Height of Handle Grips
NOTE: There are 4 Height Risers provided with this gear. You can very easily increase the height of Grips as per requirement.
- Take the Handle Bar Grip, and loosen all 4 screws to remove Tube Clamps. Then attach Height.
- Risers with Clamps.
- Now fix these Clamps with Handle Bar Grip and tighten the screws back. Your Handle Bar
- The grip has more height now and will look as shown in the image.
OUR PROAIM 2-AXIS EQUALISER FOR THE FLYCAM FLOWLINE IS ALL DRESSED UP AND READY TO GO!
SHOWN WITH OPTIONAL ACCESSORIES)
Warranty
We offer a one-year warranty for our products from the date of purchase. Within this period, we will repair it without charge for labor or parts. Warranty doesn’t cover transportation costs nor does it cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspection and evaluation by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in transit, accident, misuse, neglect, or lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissatisfaction, please Contact us immediately and we promise our utmost support and care until you use our product.
Documents / Resources
 |
PROAIM ST-EQZR-00 2-Axis Equalizer [pdf] Instruction Manual ST-EQZR-00 2-Axis Equalizer, ST-EQZR-00, 2-Axis Equalizer, Equalizer |