Pro-Ject T2 Audio Systems Instruction Manual

Contents hide

1 Pro-Ject T2 Audio Systems

2 GENERAL INFORMATION

3 Accessories

4 Maintenance and cleaning

5 Warranty

6 Declaration of Conformity

7 Warranty

8 PRODUCT INFORMATION

9 Documents / Resources

9.1 References

10 Related Posts

Pro-Ject T2 Audio Systems

Dear Music Lover,
Congratulations and thank you for choosing Pro-Ject Audio Systems record player.
Your T2 turntable has been handcrafted and rigorously tested by skilled technicians to give you years of enjoyable, trouble-free service.
If you require additional assistance, please contact your dealer.

Important:
Your turntable was shipped partially disassembled to avoid damage to sensitive parts. Please check immediately to ensure that neither the packaging nor the device was damaged in transit. If you are missing parts or if the unit is damaged, please do not operate it and contact your dealer.

Please do your part to help protect the environment

Disposal of packaging material:
Pro-Ject packaging is carefully designed to protect your component from damage during transit, and you are strongly urged to keep the original packaging to safely ship or otherwise transport your turntable in the future. However, the packaging materials were chosen to be environmentally friendly, so if you must discard the packaging, please recycle it.

GENERAL INFORMATION

Controls, features and connections

PLATTER & FELT MAT

CHASSIS
SPEED CONTROL BUTTON

MOTOR WITH PULLEY
DRIVE BELT

SUB-PLATTER
TONEARM COUNTERWEIGHT

ANTI-SKATING ADJUSTMENT SCREW WITH SCALE
TONEARM REST / REMOVABLE TRANSPORT LOCK

TONEARM LIFT LEVER
TONEARM TUBE

HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED CARTRIDGE
LID

LID HINGES
HINGE FASTENERS

POWER SUPPLY SOCKET
RCA OUTPUT BOX

Accessories

SINGLE ADAPTOR
ALLEN KEY 1,5mm

COUNTERWEIGHT no. 105 (FOR CARTRIDGE WEIGHT 5 – 11.5g)
TWO-POINT CARTRIDGE ALIGNMENT PROTRACTOR

CONNECTION CABLE (CONNECT IT E RCA)
SETUP GUIDE

UNIVERSAL POWER SUPPLY

SETUP

Platter and drive belt installation
Please remove drive belt from accessories box and install it as shown in the following illustration. Put the felt mat on the top of the platter

Cartridge installation, stylus exchange
* If you purchased this turntable in a package that included the cartridge, this has already been done for you.
Install the cartridge into the aluminium headshell, using the appropriate hardware included with your cartridge. All cartridges with half inch mounting holes can be fitted.
Connect the cartridge as indicated below:

White left channel L+
Red right channel R+
Green right channel R-
Blue left channel L-
For correct cartridge alignment, use the two-point cartridge alignment protractor provided with your T2 accessories. If unfamiliar with two-point setup, please refer to your dealer.
A damaged or worn stylus may harm your record collection and should be replaced.
Please remove stylus protection before pulling the stylus from the cartridge and replace for a new one.
Stylus type is exchange for pre-mounted cartridge Sumiko Rainier: Stylus Sumiko Rainier. If in doubt, consult your local dealer or di

Vertical Tracking Force setting (VTF)
The T2 Super Phono comes with the counterweight already assembled on the tonearm, and the tracking force is factory pre-adjusted.
To adjust or fine tune the tracking force manually, loosen the hexagonal screw on top of the counterweight (7) using the allen key provided. Remove the stylus protection cover and place the stylus pressure gauge onto the platter. To set the required VTF, lower the tonearm lift lever (10) as indicated in the illustration and place the tip of the stylus on one of the points on the scale. For example, the Sumiko Rainier requires 20mN of tracking force, so place the stylus on the 20mN point.
If the stylus gauge becomes level when the tonearm is lowered down onto the desired point, then the correct pressure has been achieved. However, if there is insufficient or excessive pressure, the gauge will either not move or tilt down.

To adjust the amount of pressure, carefully move the counterweight (7) along the support rod, until the stylus pressure is sufficient to raise the pressure gauge to the level position. Moving the counterweight (7) away from the cartridge will reduce pressure and towards will increase pressure. Finally secure the counterweight (7) using hexagonal key provided.

Maintenance and cleaning

Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.
If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.

Switching on and off, changing replay speed
The turntable is equipped with a three-position switch for ON/OFF and electronic speed change. To play records at 33 rpm. press this switch (3) to the rear side. To play records at 45 rpm. press this switch (3) to the front side as shown on illustration below. Anti-skating
The anti-skating force is pre-adjusted from the factory corresponding to the tracking force.
Sumiko Rainier recommended tracking force 20mN = anti-skating set to 2 (middle position).
You can adjust the anti-skating by rotating the anti-skating setting screw to the left or right. Connection to the amplifier
Connect the tonearm cables to the Phono input (sometimes labelled gram, disc, or RIAA) on your amplifier.
Ensure that the phono input offers the correct matching and amplification for the type of cartridge used. Line inputs (such as CD, Tuner, Tape, or Video) are not suitable. Be sure to connect the left and right channels
correctly. The right channel is usually marked red, and the left channel is black or white. Check the manual supplied with your amplifier for relevant information. An earthing wire may be connected to the screw terminal on your amplifier if you encounter hum problems when using the record player. If your amplifier does not have an input suitable for phono cartridges, you will require a separate phono amplifier stage for MM or MC cartridges, which is then connected between the record player and a free line level input on the amplifier.
For detailed product information regarding Pro-Ject Audio interconnect cables and phono amplifiers, please refer to the Pro-Ject website at www.project-audio.com

Technical specifications Pro-Ject T2 / Pro-Ject 9’’

Nominal speeds 33/45 r.p.m.
Speed variance 33: ±0.60% 45: ±0.50%
Wow and flutter 33: ±0.19% 45: ±0.17%

Signal to noise -67dB
Effective tonearm mass 9.5g
Effective tonearm length 9″ (230mm)

Overhang 22 mm
Power consumption
Power input 4.5W 15V/ 0.8 A DC, universal power supply

Dimensions (W x H x D) 457 x 134 x 335mm
Weight 5.5kg
Dimensions packaging (W x H x D) 542 x 300 x 412mm

Weight incl. packaging 8.5kg

Technical specifications MM-Cartridge Sumiko Rainier

Frequency range 15-25.000Hz

Channel separation 25dB/1kHz
Output voltage 5mV
Recommended load impedance 47kohms/amplifier connection – MM-input

Compliance/stylus type 10×10-6cm/dyn @ 100Hz– elliptical
Recommended tracking force
Capacitance 20mN 100pF – 200pF

Weight 6.5g

Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore, the following list of common fault symptoms is included.

The platter doesn’t turn although the unit is switched on

The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
Correct input not selected at amplifier.

Amplifier is not switched on.
Amplifier or speakers are defective or muted.
No connection to the loudspeakers.

Distorted or inconsistent sound from one or both channels:

Record player is connected to wrong input of amplifier.
Needle or cantilever damaged.

Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason, we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt.
Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems Copyright © 2024. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.

Declaration of Conformity

We, SEV Litovel, s r.o.
Palackého 1160/34

78401 Litovel
Czech Republic (manufacturer) and
Pro-Ject Audio Systems a division of Audio Tuning GmbH

Margaretenstrasse 98 1050 Vienna, Austria (distributor)
declare under our responsibility that the product is in conformity with the provisions of Directives:
2014/35/EU including amendments

2014/30/EU including amendments
2014/53/EU including amendments
The following harmonised standards were applied:

Health: EN62479:2010
Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, EN62368-1:2014/A11:2017, EN61558-1:2005/A1:2009, EN61558-2-16:2009/A1:2013
EMC: EN301489-1 V2.2.0: 2017-03, EN301489-17 V3.2.0:2017-03, EN55032:2015, EN55035:2017, EN61000-3-2:2014, EN61000-3-3:2013

Radio Spectrum: EN300328 V2.1.1 (2016-11)
Pro-Ject Audio Systems a division of Audio Tuning GmbH
1050 Vienna, Austria, Margaretenstrasse 98 info@project-audio.com

T2 | Setup Guide

Getting started:

Make sure to have enough space to unpack your turntable.
Always unpack and set up in a clean environment.
Please Do NOT throw away the packaging!
If you need service or want to return your product, please send it inthe original packaging including all inserts. In case of damage due to alternative packaging your dealer cannot guarantee a full refund.

Full manual: www.project-audio.com/en/product/t2

Need help?
Feel free to contact us. We have experienced partners all over the world. Find your dealer here: www.project-audio.com/en/find-a-dealer/

Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt.
Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.

Warranty

Warranty: Terms and Conditions

A warranty is valid only for products purchased from an authorized Pro-Ject Audio Systems retailer or dealer.

This warranty offer is limited to the repair of the equipment (which could be a repair or replacement at our discretion, neither of which affects your original warranty).
Neither transportation or any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty.
A warranty is only valid for the original owner. It is not transferable.

To validate your warranty, you will need to provide the original sales invoice or other proof of ownership and date of purchase.
Warranty must be claimed within two years of purchase from an authorized dealer. After this period of time, the warranty will expire.
The legal warranty obligation exists in addition to this warranty and is not limited by this warranty.

A Pro-Ject Audio Systems warranty relates to claims of defects in materials and/or workmanship at the time of purchase. It does not cover:
Deterioration of component parts, the nature of which is to become worn or depleted with use, such as batteries and headphone ear pads, drive belts and cartridges.
Damages caused by incorrect installation, connection or packing.

Damages caused by any use other than the correct use described in the user manual, negligence, modifications, or use of parts that are not made or authorized by Pro-Ject Audio Systems.
Damages caused by faulty or unsuitable ancillary equipment.
Damages caused by accidents, lightning, water, fire heat, war, public disturbances or any other cause beyond the reasonable control of
Pro-Ject Audio Systems and its appointed distributors.

Products where the serial number has been altered, deleted, removed or made illegible
Repairs or modifications that have been executed by an unauthorized person.

Commercial Use
Faults caused due to using domestic products in commercial environments or on commercial scales are not covered by warranty. This turntable is intended for domestic use only. Using them for business applications are done so at your own risk.
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems

Copyright © 2023. All rights reserved.
The information, pictures and figures were correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
Contains FCC ID: 2AJYB-S1955

PRODUCT INFORMATION

NEW 9“ highly precise and light aluminium tonearm
NEW Spring based anti-skating system

NEW Counterweight with nickel finish
NEW larger chassis for higher stability
NEW Preadjusted Sumiko Rainier (MSRP 175€)

NEW 10mm, 1,7kg zero-resonance glass platter
NEW Speed control with electronic speed switch
One-piece tonearm with integrated headshell

Belt-driven
No hollow spaces for optimal sonic performance
Vibration absorbing feet

Semi-symmetrical phono cable with metal connectors
Acrylic dustcover with adjustable hinges
Available in high gloss Black, satin White and Walnut

Handmade in Europe
Speed: 33,45 RPM (electronic speed change)
Principle: Belt drive

Speed variance: 33: 0,6% 45: 0,5%
Wow & Flutter: 33: 0,19% 45: 0,17%
Platter: 10mm thick, 1,7kg heavy glass platter with felt mat

Main bearing: Stainless steel/brass
Signal to noise: 67dB
Tonearm: 9” aluminium

Effective arm length: 230 mm
Overhang: 22.0 mm
Effective tonearm mass: 9.5 g
Included accessories: dustcover, feltmat, singles adapter,
power supply, RCA cable
Power Supply: 15V / 800 mA DC, universal power supply
Power consumption: 4,5 W / 0 W in Stand-By
Dimensions: 542 x 300 x 412mm (WxHxD)
Weight: 5,5 kg net

T2: A New Modern Marvel
The T2 sensibly enhances our critically acclaimed T1 for-mula, introducing many new audiophile features, setting new standards in its new price-range.

Highest Quality Materials
The elegantly crafted CNC-machined plinth has been expanded in size to enhance stability and is available in striking finishes such as High Gloss Black, Satin White, or Walnut. It boasts a construction free of plastic com-ponents and meticulous manufacturing that eliminates any hollow spaces within, effectively preventing un-wanted vibrations within the chassis. Furthermore, the glass platter in the T2 has been made heavier and thicker compared to its predecessor, ensuring a zero-resonan-ce design that effectively eliminates the shortcomings associated with plastic or lightweight steel alternatives. Complementing these improvements, purpose-selected turntable feet effectively isolate the T2 from ambient vi-brations present in the vicinity of your hi-fi system.Speed Control, Motor and Drive
The motor and drive system in the T2 remain identical to those found in the T1. The motor drives a belt system, connected to our newly designed sub-platter exclusive to the T-line. This sub-platter is mounted on an ultra-pre-cise 0.001mm main bearing with a hardened steel axle and brass bushing. Where most alternative products may use un-regulated DC motors with wide speed fluc-tuations, the T2 features our proven system of an elec-tronically regulated, precision-speed AC motor. The T2 also comes with electronic speed switching bet-ween 33 and 45 RPM. The result is a low-noise, stable drive system for the turntable. New Tonearm & Anti-Skating
The tonearm on the T2 has been improved with a longer arm tube. With its straight, 9” effective length and stiff aluminium construction, this one-piece tonearm also features new updated low-friction bearings to accom-modate the increased length and diameter for absolute accuracy in use. Besides the clean and stylish looks, the integrated headshell won‘t cause any additional vibra-tions either, and is a big improvement over other de-tachable, screwed-on or glued-on headshells! The T2 also comes brand new with an adjustable spring-based anti-skating mechanism that optimizes performance and extracts the utmost potential from your cartridge. Sumiko Rainier MM cartridge
The T2 comes preadjusted with a high-value Sumiko Rainier MM cartridge (MSRP 175€) featuring an ellipti-cal diamond stylus tip; this is a true hi-fi playback sys-tem with no corners cut.

Semi-balanced phono cable
Like the T1, the T2 is then finished with super shielded, semi-symmetrical, low-capacitance phono cables, purpose-designed by Pro-Ject – not off-the shelf RCA cables. There is also a dust cover for extra protection and a felt mat to protect your records.

The True Balanced Upgrade
The T2 has gold plated RCA outputs with completely symmetrical signal wiring, like any other Pro-Ject turn-table with phono RCA outputs too. This means by upgrading to a MC cartridge or our Pick it PRO Balanced – our specially designed balanced MM cartridge – and using one of our balanced phono stages, like the Phono Box S3 B or DS3 B, with one of our True Balanced cables, you can leverage all the advantages our True Balanced Connection has to offer. Less noise, more dynamics, clean and punchy transients and simply a deeper musical involvement. The new 9“ tonearm and adjustable anti-skating make the T2 play perfectly with a wide range of high-end MC cartridges.