Print Your Speakers ND25FA-4 Glow 4c 3D Printed Center Channel Speaker
Specifications:
- Product Name: Glow 4c DIY Speaker Kit
- Version: V1.0
- Website: www.printyourspeakers.com
Product Information:
The Glow 4c DIY Speaker Kit is designed for sound crafters looking to build their custom speakers. It includes a variety of high-quality components that are carefully selected to enhance the audio experience.
Components Included:
- Dayton Audio ND25FA-4 Tweeter
- Dayton Audio TCP115-4 Woofer
- Binding Posts (Dayton BPA-38G suggested)
- Inductors: 0.1mH, 0.15mH, 0.4mH
- Resistors: 5.1 Ohm, 5.6 Ohm, 8 Ohm
- Capacitors: 2.2uF, 4.7uF, 22uF
- Crossover Capacitor
- Gasketing Tape
- CNC Kitchen M4 Threaded Inserts
- M4 10mm Cap Head Screws
- Epoxy Glue
- Cable Ties (small)
Product Usage Instructions
Step 1: Component Assembly
Follow the provided assembly guide to correctly assemble the components into the speaker enclosure.
Step 2: Wiring
Connect the components following the wiring diagram provided with the kit. Ensure all connections are secure and insulated.
Step 3: Enclosure Sealing
Use the gasketing tape to seal any gaps in the speaker enclosure to prevent sound leakage.
Step 4: Mounting
Secure the speakers using the M4 threaded inserts and screws. Ensure the speakers are mounted firmly for optimal performance.
YOUR DIY SPEAKER SHOPPING GUIDE
- Alright, sound crafters! Below is your treasure map to all the parts you’ll need for your custom speaker. We’ve sorted everything by where you can buy them to make your shopping trip a breeze. Remember, picking the right parts will amp up your audio experience!
| QTY PER SPEAKER |
COMPONENT |
PRODUCT CODE |
WHERE TO GET IT (EU, US, AU) |
| 1 | Dayton Audio ND25FA-4 | ND25FA-4 | US, EU, AU |
| 2 | Dayton Audio TCP115-4 | TCP115-4 | US, EU, AU |
| 1 pair | Binding Posts (Dayton BPA- 38G suggested) | BPA-38G | US, EU, AU |
| 1 | 0.1mH Inductor | AC20-10 | US, EU, AU |
| 1 | 0.15mH Inductor | AC20-15 | US, EU, AU |
| 1 | 0.4mH Inductor | AC20-40 | US, EU, AU |
| 1 | Dayton Audio 5.1 Ohm Resistor | DNR-5.1 | US, EU, AU |
| 1 | Dayton Audio 5.6 Ohm Resistor | DNR-5.6 | US, EU, AU |
| 1 | Dayton Audio 8 Ohm Resistor | DNR-8.0 | US, EU, AU |
| 1 | Dayton Audio 2.2uF Capacitor | DMPC-2.2 | US, EU, AU |
| 1 | Dayton Audio 4.7uF Capacitor | DMPC-4.7 | US, EU, AU |
|
1 |
22uF Capacitor |
22uF 100V Electrolytic Non-Polarized Crossover Capacitor |
US, EU, AU |
| 15cm | Gasketing tape | US, EU, AU | |
| 24 | CNC Kitchen m4 Threaded Inserts | M4x8.1 | World Wide |
|
24 |
M4 10mm Cap Head Screws |
|
Local Hardware Store, Speaker Component Store, Amazon (Search: M4 10mm socket head cap screw) |
| ~5ml | Epoxy Glue | Local Hardware Store, Speaker Component Store, Amazon | |
| 15 | Cable Ties (small, <5mm wide) | Local Hardware Store, Speaker Component Store, Amazon | |
| 1-2 sticks | Hot Glue | Local Hardware Store, Speake Component Store, Amazon | |
| 20g | Solder | Local Electronics Store, Speaker Component Store, Amazon | |
| 100cm | Speaker wire | Local Electronics Store, Speaker Component Store, Amazon | |
| 250x500mm | Dacron Sheet | Local Sewing/Craft Store, Amazon, eBay | |
| ~1900g | PLA Printer Filament | Any 3D printing store | |
|
10g |
TPU Printer Filament for feet (alternatively you can purchase rubber feet) |
Any 3D printing store |
Safety Instructions for ND25FA-4 Glow 4c Center Channel Speaker
| Category | Instructions |
|---|---|
| 1. Electrical Safety | Use only the recommended amplifier wattage and impedance (4 ohms) to prevent damage. |
| 2. Ventilation | Keep vents unobstructed to avoid overheating. Do not cover the speaker with fabric or enclosures. |
| 3. Placement | Place on a flat, stable surface. Avoid high shelves or unbalanced stands. |
| 4. Moisture Protection | Keep speaker away from water, rain, and damp environments. Not suitable for outdoor use unless specified. |
| 5. Heat Sources | Do not place near radiators, stoves, or heat-producing electronics. |
| 6. Power Connection | If powered externally, ensure the power source is off before connecting or disconnecting. |
| 7. Cleaning | Unplug any connected cables before cleaning. Use a dry cloth—avoid liquids or sprays. |
| 8. Wiring Safety | Use quality speaker wire and secure connections. Avoid exposed or frayed wires. |
| 9. Magnet Warning | Contains strong magnets. Keep away from pacemakers and magnetic storage devices. |
| 10. Children & Pets | Keep out of reach of children and pets to prevent tipping or damage. |
| 11. 3D Printed Parts | Avoid exposing printed parts to extreme heat or prolonged sunlight, may deform. |
| 12. Shock Risk | Do not open or modify internal components—risk of electric shock or damage. |
| 13. Overdriving | Avoid playing at maximum volume for extended periods to prevent distortion or damage. |
| 14. Transport | When moving the speaker, use both hands and avoid dropping. |
| 15. Inspection | Regularly check for damage to wires, terminals, and housing—stop using if damaged. |
Link not working? Item out of stock?
No worries! Just shoot us an email at help@printyourspeakers.com, and we’ll update the guide and help you find what you need.
FAQs
Q: Can I customize the components in the Glow 4c DIY Speaker Kit?
A: While we recommend using the specified components for the best audio quality, you can experiment with different components to suit your preferences.
Q: How do I know if I have assembled the speakers correctly?
A: Refer to the assembly guide and wiring diagram provided in the kit. You can also perform a sound test to ensure all components are functioning properly.
Documents / Resources
 |
Print Your Speakers ND25FA-4 Glow 4c 3D Printed Center Channel Speaker [pdf] User Guide ND25FA-4, TCP115-4, BPA-38G, AC20-10, AC20-15, AC20-40, DNR-5.1, DNR-5.6, DNR-8.0, DMPC-2.2, DMPC-4.7, ND25FA-4 Glow 4c 3D Printed Center Channel Speaker, ND25FA-4, Glow 4c 3D Printed Center Channel Speaker, Printed Center Channel Speaker, Center Channel Speaker, Channel Speaker |