Unclogs Pro / Unclogs Pro Plus with AIS
Universal Process Data Recorder PC Software Version
Operation Manual
UniLog Pro Universal Process Data Recorder PC
| OPERATOR PARAMETERS | |
| Parameters | Settings (Default Value) |
‘Start’ Command for Batch Recording (Available if Batch Recording is selected) |
No Yes |
‘Stop’ Command for Batch Recording (Available if Batch Recording is selected) |
No Yes |
SUPERVISORY CONFIGURATION
Note: AII the other Parameters are under SUPERVISORY CONFIGURATION
| ALARM SETTING | |
| Parameters | Settings(Default Value) |
Channel Name for Alarm Settings |
User defined or default names for channel-1 to channel-8 / 16 (Default : NA) |
Select Alarm |
AU , AL2, AL3, AL4 (The actual available options depends on the numbers of Alarms set per channel on Alarm configuration page) |
Alarm Type |
None Process Low Process High (Default : None) |
Alarm Setpoint |
Min. to Max. of selected input type range (Default : 0) |
Alarm Hysteresis |
1 to 3000 or 0.1 to 3000.0 (Default : 2 or 2.0) |
Alarm Inhibit |
No Yes (Default : No) |
| DEVICE CONFIGURATION | |
| Parameters | Settings (Default Value) |
Channel Update Time in Auto Scan Mode |
1 Sec. to 99 Sec. (Default: 3 Sec.) |
Device Identification Number |
1 to127 (Default : 1) |
Select Total Numbers of Channels |
8 16 (Default : 16) |
Erase All Stored Records |
No Yes (Default : No) |
| CHANNEL CONFIGURATION | |
| Parameters | Settings (Default Value) |
Select Channel Name |
User defined or default names for channel-1 to channel – 8 / 16 (Default : NA) |
Skip Channel for Display |
No Yes (Default : Yes) |
Signal Input Type |
Refer Table 2 (Default : Type K (Cr-Al) |
Display Resolution for Measured PV |
1 Unit 0.1 Unit 0.01 Unit 0.001 Unit (Default : 0.1 Unit) |
Display Units for Measured PV |
Refer Table 1 (Default : °C) |
Range Low |
-19999 to 30000 Counts with Selected Resolution (Default : 0.0) |
Range High |
-19999 to 30000 Counts with Selected Resolution (Default : 100.0) |
Apply Lower Clip on Displayed PV |
Disable Enable (Default : Disable) |
Preset Lower Clip Level |
-19999 to 30000 (Default : 0) |
Apply Upper Clip on Displayed PV |
Disable Enable (Default : Disable) |
Preset Upper Clip Level |
-19999 to 30000 (Default : 100.0) |
Zero Offset |
-1999 / 3000 or -1999.9 / 3000.0 (Default : 0) |
| ALARM CONFIGURATION | |
| Parameters | Settings (Default Value) |
Alarms Per Channel |
1 to 4 (Default : 4) |
Relay-1 Logic |
Normal Reverse (Default : Normal) |
Relay-2 Logic |
Normal Reverse (Default : Normal) |
| RECORDER CONFIGURATION | |
| Parameters | Settings (Default Value) |
Normal Recording Interval |
0:00:00 (H:MM:SS) to 2:30:00 (H:MM:SS) (Default : 0:00:30) |
Zoom Recording Interval |
0:00:00 (H:MM:SS) to 2:30:00 (H:MM:SS) (Default : 0:00:01) |
Record Generation on Alarm Status Toggle |
Disable Enable (Default : Enable) |
Select Recording Mode |
Continuous Batch (Default : Continuous) |
Time Interval for Batch Recording |
0:01 (HH:MM) to 250:00 (HHH:MM) (Default : 1:00) |
| RTC SETTING | |
| Parameters | Settings |
Set Clock Time (HH:MM) |
0.0 to 23:59 |
Set Calendar Date |
1 to 31 |
Set Calendar Month |
1 to 12 |
Set Calendar Year |
2000 to 2099 |
| UTILITIES | |
| Parameters | Settings |
Master Lock Enable Disable |
No Yes |
UIM Default |
No Yes |
CIM Default |
No Yes |
Make CIM & UIM Compatible |
No Yes |
* For Uni Log Pro Plus with more Than One AIS Only
| TABLE-1 | |
| Option | Description |
| °C | Degree Centigrade |
| °F | Degree Fahrenheit |
| (none) | No Unit (Blank) |
| °K | Degree Kelvin |
| EU | Engineering Units |
| Percentage | |
| Pa | Pascals |
| Mpa | Pascals |
| kPa | Pascal’s |
| bar | Bar |
| mbar | Millie bar |
| psi | PSI |
| kg/sq.cm | kg/cm2 |
| mmH2O | mm water gauge |
| inH2O | Inches water gauge |
| mmHg | mm mercury |
| Torr | Torr |
| litre/hr | Litres per hour |
| litre/min | Litres per minute |
| %RH | % Relative Humidity |
| %02 | % Oxygen |
| %002 | % Carbon di-oxide |
| %CP | % Carbon Potential |
| V | Volts |
| A | Amps |
| mA | Millie Amps |
| mV | Millis Volts |
| ohm | Ohms |
| ppm | Parts per million |
| rpm | Revolutions per minute |
| music | Millie seconds |
| Sec | Seconds |
| min | Minutes |
| hrs | Hours |
| PH | PH |
| %PH | %PH |
| miles/hr | Miles per hour |
| mg | Millie grams |
| g | Grams |
| kg | Kilo grams |
| TABLE- 2 | ||
| Option | Range (Min. to Max.) | Resolution |
 J Type T/C |
0 to +960°C / +32 to +1760°F | Fixed 1°C / 1°F |
 K Type T/C |
-200 to +1376°C / -328 to +2508°F | |
 T Type T/C |
-200 to +385°C / -328 to +728°F | |
 R Type T/C |
0 to +1771°C / +32.0 to +3219°F | |
 S Type T/C |
0 to +1768°C / +32 to +3214°F | |
 B Type T/C |
0 to +1826°C / +32.0 to +3218°F | |
 N Type T/C |
0 to +1314.0°C / +32 to +2397.0°F | |
 |
Reserved for customer specific Thermocouple type not listed above. | |
 RTD Pt100 |
-199 to +600°C / -328 to +1112°F or -199.9 to 600.0°C/ -328.0 to 1112.0°F | User settable 1°C/ 1°F or 0.1°C / 0.1°F |
 0 to 20mA DC |
-19999 to +30000 units | User settable 1 / 0.1 / 0.01/ 0.001 units |
 4 to 20mA DC |
||
 0 to 50mV DC |
||
 0 to 200mV DC |
||
 0 to 1.25V DC |
||
 0 to 5.0V DC |
||
 0 to 10.0V DC |
||
 1 to 5.0V DC |
||
ID SETTING FOR MORE THAN 1 AIS
Applicable only for UNILOG PRO PLUS
FRONT PANEL LAYOUT
| Symbol | Key | Function |
 |
PAGE | Press to enter or exit set-up mode. |
 |
DOWN | Press to decrease the parameter value. Pressing once decreases the value by one count; holding pressed speeds up the change. |
 |
UP | Press to increase the parameter value. Pressing once increases the value by one count; holding pressed speeds up the change. |
 |
ENTER | Press to store the set parameter value and to scroll to the next parameter on the PAGE. |
PV Error Indications
| Error Message | Cause |
| Over Range | Process Value above Max. Range |
| Under Range | Process Value below Min. Range |
| Sensor Open | Thermocouple / RTD broken |
| Com. Fail | Communication Link with CI M broken |
ELECTRICAL CONNECTIONS
USER INTERFACE MODULE (UIM)
COMMUNICATION PORT FOR INTERFACING WITH AIS(S)
Applicable only for UNILOG PRO PLUS
ANALOG INPUT MODULE CONNECTIONS
AIS-8UM
AIS-16UM
101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar – 401 210.
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
E: sales@ppiindia.net, support@ppiindia.net
Jan 2022
Documents / Resources
 |
PPI UniLog Pro Universal Process Data Recorder PC [pdf] User Manual UniLog Pro Universal Process Data Recorder PC, UniLog Pro, Universal Process Data Recorder PC, Process Data Recorder PC, Data Recorder PC, Recorder PC, PC |
