POWER-POLE AVG-MP-0915 PV Extension Pulpit

Product Information

Specifications

• Hardware Included: Screws, Pulpit Plate, Rubber Washers, Stainless Steel Washers, Nylon Lock Nuts, Hex Head Bolts, Lock Washers

FAQ

• Q: What should I do if I encounter difficulties during installation?
  • A: Contact our Customer Service Team at 1 + 813.689.9932 Option 2 for assistance.

TOOLS AND HARDWARE

TOOLS:

• #2 Phillips Head Screwdriver
• #3 Phillips Head Screwdriver
• 7/16” Socket
• 7/16” Wrench
• Ratchet
• Electric Drill
• 5-16” Drill Bit

INCLUDED HARDWARE

QTY.	LABEL	ITEM #	DESCRIPTION
6	A	AVG-MH-SC-0318	1/4”-20, Full Thread, 3”, Stainless Flat-Head Phillips Drive Screw
1	B	AVG-MP-0936	Pulpit Plate, Short
6	C	AVG-MP-0915	Thick Rubber Washer
6	D	AVG-MH-WS-0306	1/4” Large Stainless Steel Flat Washer
6	E	nut-14-tall	1/4” Brass Tall Nylon Lock Nut
4	F	AVG-MH-BT-0320	1/4”-20, 1 1/8” Stainless Hex Head Bolt
2	G	AVG-MH-BT-0319	1/4”-20, 7/8” Stainless Hex Head Bolt
6	H	AVG-WASH-14-PP	1/4” Stainless Lock Washer
6	I	AVG-MH-WS-0321	1/4” Small Stainless Steel Flat Washer

DETERMINE MOUNTING LOCATION

After reading the Mounting Parameters lay the Pulpit B on the boat deck and line up the mounting holes on the included PV Mounting Template (included with trolling motor) with the holes on the Pulpit B . Move the Pulpit B into position so the Cam Arms have proper clearance and all parameters are met.

MOUNTING PARAMETERS

• Ensure there are no obstructions or sensitive components where the mounting hardware will be installed.
• Make sure the cam arms can have a full range of motion and will not hit the boat when the unit is deployed.
• Ensure there are no obstructions blocking the motor from fully deploying and stowing.
• If mounting to a curved Boat Deck, ensure Rubber Washers C are used between the Pulpit and Deck.

DRILL PILOT HOLES

• Drill Pilot holes for the Flat Head Screws A using a 5/16” Drill Bit.
• Use the furthest possible forward two holes, the furthest possible back two holes, and two holes that are spaced evenly in between the others.

Caution: Check the area beneath where the Pulpit will be mounted to ensure there are no hoses, wires lines tanks or other sensitive components.

IMPORTANT

• If installing to gel-coat, follow the drilling procedure in Appendix A of the Installation & Owner’s Guide to ensure you do not crack or chip the gel-coat.
• Make sure the cut-out is facing the front of the boat and the counter-sunk holes are facing upright.

INSTALLATION INSTRUCTIONS

INSTALL PULPIT

Install the Pulpit Mounting Hardware in order. While holding Screws A with a #3 Phillips Head Screwdriver, tighten hardware snug using a 7/16” Socket & Wrench.

1. (6) Screws A
2. Pulpit B
3. (6) Rubber Washers C if needed
4. Boat Deck
5. (6) Large Washers D
6. (6) Nylon Lock Nuts E

NOTICE: If Installing the PV to Pulpit using a Quick Disconnect Mount, follow the Mounting the Move PV Section in the Installation Owner’s Guide.

Warning

• Always disconnect power by turning the main battery cutoff switch to the off position before performing any installations.

REMOVE SPRINGS AND SHROUDS

• STEP 1 Using a #2 Phillips Screwdriver, remove the (2) Screws that attach the Shroud Assembly.
• STEP 2 Rotate the Shroud Assembly so it is resting against the Die Cast Motor Housing.
• STEP 3 (Optional for easiest install) Remove the (2) Springs by pulling upward and sliding the spring eye off of the spring post.

REMOVE QUICK DISCONNECT HARDWARE

• STEP 1 While holding the rear two Flat Head Screws with a #3 Phillips Screwdriver, loosen the Hex Nuts using a 7/16” Socket and Ratchet, then remove hardware. FIG A
• STEP 2 Push down on and hold the Foot Pedal so the arms slide backward, allowing the additional (4) Screws to be accessed. FIG B
• STEP 3 Repeat STEP 1 for the remaining (4) Screws and hardware. FIG A

NOTICE

• You will need to use an extension to reach the front four nuts.

INSTALL PV TO PULPIT

Install the PV mounting hardware in order. Tighten hardware snug using a 7/16” Socket & Wrench.

1. (6) Bolts ( F for the front four mounting holes, G for the rear two mounting holes)
2. (6) Lock Washers H
3. (6) Small Washers I
4. Pulpit B

NOTICE

• You will need to use an extension to reach Bolts F .
• You will need to engage the Foot Release to reach Bolts F .

INSTALL SPRINGS AND SHROUDS

• STEP 1 Reinstall the (2) Springs.
• STEP 2 Flip the Shroud Assembly down, ensuring the Shrouds are interlocking not overlapping.
• STEP 3 Install the Screw on either side of the unit. Using a #2 Phillip’s Screwdriver, tighten snug.

Contacts

• 9010 Palm River Road, Tampa, Florida 33619
• phone 813.689.9932
• fax 813.689.8883
• power-pole.com

Power-Pole is a registered trademark of JL Marine Systems, Inc.
© Copyright 2023 JL Marine Systems, Inc. All Rights Reserved.

Documents / Resources

POWER-POLE AVG-MP-0915 PV Extension Pulpit [pdf] Instructions AVG-MP-0915 PV Extension Pulpit, AVG-MP-0915, PV Extension Pulpit, Extension Pulpit, Pulpit

References

• User Manual