Polygroup LUMATIONS LED Wizard 10 Setting Owner’s Manual

READ AND KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

FAILURE TO FOLLOW THESE WARNINGS AND INSTRUCTIONS CAN RESULT IN SERIOUS INJURY OR DEATH TO USERS, ESPECIALLY CHILDREN

WARRANTY

Thank you for your purchase of Polygroup” products! We do hope that you are happy with what you received, but we know sometimes it’s necessary to exchange or return an item. Therefore, Polygroup” offers a 30-day limited warranty on this product”
We are happy to repair your defective item or replace it with an item that is equal to the purchase price of the item, given that:

• You are the original purchaser for products purchased directly from an authorized retailer or wholesaler of Polygroup products:
• The item was purchased within the last 30 days,
• The item was purchased duing its intended season,
• Proof of purchase can be provided
• The item is in its original packaging.

If you meet these requirements, please contact us at warranty@polygroup.com (email) or (888) 919-0070 (phone) so that we may forward you a quality assurance form.

Note: Warranty is not extended to items that are purchased from seasonal stores as they generally sell items with an “all sales final policy. Warranty is also not extended to close-out, second quality, or resold products (Le garage sales, online auctions, or online retailers not purchased directly from Polygroup”). Any issues with items purchased from these types of vendors/sellers will need to be addressed through them.

WARNING

IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When used outdoors, this product must be connected to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
2. This seasonal use product is not intended for permanent installation or use.
3. Do not mount or place near gas or electric heaters, fireplace, candles or other similar source of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. Disconnect the product from power source when leaving the house, when retiring for the night, or if left unattended.
7. This is an electric product – not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not be played or placed where small children can reach it.
8. Do not use this product for other than its intended use.
9. Do not hang omaments or other objects from cord, wire, or light string.
10. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
11. Do not cover the product with cloth, paper or any materials not part of the product when in use.
12. This product can be used by children ages 8 years and above, and people with reduced physical, sensory or mental capabilities, if they have been given the right supervision or instructions concerning the use of the product in a safe way and understand the hazards involved. Children should not play with the product. Cleaning and user maintenance should not be made by children without supervision.
13. Risk of fire: the supply cord, adapter, plugs and/or connectors cannot be replaced or modified. If either is damaged, the product should be disposed.
14. Strobe lights have been known to trigger seizures in people with photosensitive epilepsy.
15. The controller and remote controller (if included) can only be used with this product.
16. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit ina polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully inserted. Do not alter or replace the plug.
17. This product employs overload protection (fuse). A blown fuse indicates an overload or shortcircuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
18. Read and follow all instructions that are on the product or provided with the product.

SAVE THESE INSTRUCTIONS.
CAUTION:

To reduce the risk of fire or electric shock:

• Do not mount or support cords or cables in a manner that can cut or damage wire insulation:
• Use only the adapter provided with this product:
• Make sure connectors are fully inserted and secured by fully fastening the connector rings.

Specifications

• Input: AC 120V/60Hz, 2A (Max)
• Output: AC 120V/60Hz, 4×0.5A (Max)
• Model: PDR-026-120V

USE & CARE

Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged or frayed wire insulation or cords, loose connections, or exposed copper wire.

IMPORTANT:

• Connect only standard LED lights without any functions.
• This product is equipped with an internal protection device (circuit breaker) that shuts off the power to an outlet when the outlet is overloaded. If lights with amperage over 0.5 A are plugged to the outlet, the device will automatically switch off the outlet. Remove the lights and the outlet will work normally again. See TROUBLESHOOTING
  1. . Connect your LED lights (not included) to one of the four outlets of the product. The actual number of lights to be connected to each outlet varies with the actual rated amperage of your lights. Please refer to the specifications and user manual of  your lights. Do not exceed the maximum ratedamperage or it may cause damage to the product and/or user. IMPORTANT: Connect only standard LED lights without any functions.
     
     
  2. Plug the product to a wall or electrical outlet. If an extension cord is needed, you may connect it either at position 1 (between the electrical outlet and product’s main plug) or position 2 (between one of the four outlets and light string’s plug).
     
  3. When not in use, unplug the product from power and store it in a cool, dry place away from sunlight.
  4. When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conduct

TROUBLESHOOTING

Lights of one (or more) of the outlets go off

• The outlet is overloaded. Unplug the power and wait for 30 minutes. Meanwhile check that the power output of your lights does not exceed 0.5 A, the maximum capacity of each outlet. Replace with lights of less lighting load.
• Connect with only static, constant standard LED lights without any functions.

Lights flash abnormally

• Remove your lights and replace with only static/constant LED lights without any functions or controllers; the product should then work normally.

OPERATING INSTRUCTIONS

You can customize the light functions by using either the Light Controller or the Remote Control.

1. Before using the remote control, remove the insulation tab on its rear.
2. Press the Selector Button once on either control and wait for a second to enjoy light effects in the pre-programmed sequence.
   

BATTERY REPLACEMENT OF REMOTE CONTROL

1. Loosen the screw of the battery cover with a screwdriver (not included).
   
2. Replace the used battery with a new CR2032 button cell battery (not included). Make sure that the battery is installed with the correct polarity (+ and -).
3. Retighten the screw to close and secure the battery cover.
   

WARNING

1. This product is powered by a lithium battery. Due to their small size, lithium batteries can easily be swallowed by children. Ingestion of such batteries has been known to cause death.
2. This is a lithium battery which if swallowed has been known to cause death.
3. Small parts, keep batteries out of reach of children.
4. Do not expose the remote controller to moisture.
5. Clean the battery contact surfaces prior to battery installation.
6. Use only CR2032 3V battery for remote controller.
7. Do not dispose of batteries in fire-batteries may leak or rupture.
8. Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries
9. Ensure the batteries are installed correctly according to polarity (+ and-).
10. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
11. Non-rechargeable batteries are not to be recharged.
12. Do not force discharge, recharge, disassemble, heat above 60 C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical bums.
13. Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
14. Even used batteries may cause severe injury or death.
15. Call a local poison control center for treatment information.
16. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

This symbol marked on the product indicates “Warning: contains coin battery”

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN
  Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
  

Fuse Replacement:

1. Grasp the plug and unplug the product from power. Do not unplug by pulling on the cord.
2. Slide open the fuse cover and remove the blown fuse carefully.
3. Insert the included spare fuse.
   Risk of fire: replace only with 7 Amp 125 Volt fuse provided with the product
4. Close the fuse cover.
   

FUNCTIONS

NOTE: To get the full effects of Shows #4-10, make sure lights are plugged into all four outlets.

1. Press to select from the 10 preset shows in the follow sequence or to turn off the lights.
   • Show #1: Steady Glow
   • Show #2: Multi-speed Fading
   • Show #3: Multi-speed Blinking
   • Show #4: Chasing (Light effects will be played in sequence through every active port.)
   • Show #5: Shooting Star
   • Show #6: Stacking
   • Show #7: Sparkle
   • Show #8: Cross Wave
   • Show #9: Alternating
   • Show #10: Combo
     OFF: Press once after Show #10 to turn off the lights.
   • If you unplug and reconnect the product to the power outlet, the product will replay the last show that was playing before cutting out the power.
2. Press to select from the 4 preset timer settings:
   a. Setting 1: Lights ON for 4 hours and then OFF for 20 hours (LED indicator on Light Wizard will be Green).
   b. Setting 2: Lights ON for 6 hours and then OFF for 18 hours (LED indicator on Light Wizard will be Blue).
   c. Setting 3: Lights ON for 8 hours and then OFF for 16 hours (LED indicator on Light Wizard will be Red).
   d. Setting 4: TIMER OFF (LED indicator on Light Wizard will be Yellow).
   The LED light on the remote control will blink 5 times in red before turning off when “Timer off” setting is selected.
3. The timer will reset after each Show/Timer selection, and after you unplug and reconnect the product to the power outlet.
   

Documents / Resources

Polygroup LUMATIONS LED Wizard 10 Setting [pdf] Owner's Manual LUMATIONS LED Wizard 10 Setting, LUMATIONS, LED Wizard 10 Setting, Wizard 10 Setting, 10 Setting, Setting

References

• User Manual