POLARIS RZR Pro Series Ride Command Stage 6 Stereo Kit Instruction Manual

POLARIS RZR Pro Series Ride Command Stage 6 Stereo Kit

Contents hide

1 INCLUDED IN THE KIT

6 Documents / Resources

6.1 References

7 Related Posts

INCLUDED IN THE KIT

UTV Stereo RZR Pro Series Ride Command Stage 6 Kit

UTV Stereo Polaris RZR Pro Series Ride Command Front & Rear RCA Output with Speaker Wire & Remote
UTV Stereo Subwoofer Level Controller with a Rocker Switch Housing

UTV Stereo Polaris RZR Pro Series Single Color Tweeter LED Harness
UTV Stereo Pro Series 6.5″ Speakers (Pair)

UTV Stereo Pro Series Tweeter with built-in smoked LED Rings (Pair)
UTV Stereo Elite Series 5 Channel Amplifier

UTV Stereo Polaris RZR Pro Series Firewall Amplifier Mount
UTV Stereo 8AWG Amp Power Harness for Installation

UTV Stereo Flex 10″ Elite Series Subwoofer 1 OHM, Dual Voice Coil
UTV Stereo Polaris RZR Pro Series 10″ Vented Sub Enclosure

UTV Stereo Amplifier to Single Subwoofer Wire Harness
UTV Stereo Wire Harness Kit

UTV Stereo RZR Pro Series Stage 6 Ride Command Kit

INSTRUCTIONS

FOLLOW INSTRUCTIONS TO INSTALL YOUR UTV STEREO STAGE KIT

Each individual part has its own specific install instructions and/or install video that can be found on that particular items page at utvstereo.com Use this resource to install each part individually.

Step 1: Run 86” Power Harness(es) from Battery through center console. Remove shift knob plastic housing to run wire through the rubber grommet. Leave battery disconnected. *Pre Install optional LED Power Harness for RGB Activation.

Step 2: Remove Upper Dash Panels
Step 3: Install Firewall Amplifier Mount and Amplifiers (Reference Firewall Amplifier Mount Instructions).

Step 4: Locate OEM amplifier in dash and unplug the factory harness. Remove factory amp. Plug pro RCA Out Harness into OEM Plug. (Reference Pro Series RCA Out Harness Instructions)
Step 5: In the dash, locate the blue OEM Sub Out Plug and Plug in Rocker Switch Bass Knob (Reference Rocker Switch Bass Knob Instructions).

Step 6: Remove all OEM speaker enclosures: rear, dash, & tweeters. Unload OEM speakers.
Step 7: Install 10” vented dash subwoofer into enclosure. Once enclosure is secure, mont subwoofer into enclosure. (Reference Pro Series 10“ Vented Dash Enclosure Instructions)

Step 8: Install Pro 6.5” Speakers into front dash pods(2) and install into OEM Locations.
Step 9: Install Tweeters into OEM Location. *Connect optional LED Power Harness for RGB Activation. (Reference Tweeter Manual)

Step 10: Wire Pro 6.5” Speakers into (Un-Mounted) Rear Pods. (Reference Pro Series 6.5” Speaker Manual)
Step 11: Make Connections and Install (Loaded) Rear Pods(2).

Step 12: Connect Power Harness to Amplifier(s) and tune your system. (Reference Page 3).

PULSE BAR

TUNING YOUR SYSTEM

T H I S W I L L S H OW YO U E X AC T LY W H E R E T O S E T T H E ADJUSTMENTS OF YOUR AMPLIFIER(S) USE THESE SETTINGS FOR OPTIMAL PERFORMANCE!

ELITE SERIES
UTVS-E1600.5D

TUNING BLUEPRINT

‘STARTING POINT’ ▸

Cut out the image along the red outline.
Align the cutout image with the amplifier tuning panel
Make your adjustments

Documents / Resources

POLARIS RZR Pro Series Ride Command Stage 6 Stereo Kit [pdf] Instruction Manual
UTVS-PRO-S6-RC, Pro Series Ride Command Stage 6 Stereo Kit, Pro Series, Ride Command Stage 6 Stereo Kit, Stage 6 Stereo Kit, Stereo Kit

References

User Manual