PLTSP3P417 LED T8 Tube with Emergency Backup
COLOR SELECTABLE
COLOR SELECTABLE LED TS TYPE B TUBE W/ EMERGENCY BACKUP WARNING, CAUTION, SAFETY AND INSTALLATION INSTRUCTIONS
WARNING
- Installation, service, and maintenance of luminaries should be performed by a qualified licensed electrician.
- Read these instructions carefully before installation.
- Installers should examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts before installation of the retrofit kit.
- There is an emergency LED tube, installation instructions, luminaire marking labels, and miscellaneous hardware in this kit.
CAUTION
- Only those open holes indicated in the photography and/or drawing may be made or altered as a result of kit installation. Do not make any other holes in the wiring enclosure or components.
- Installers should not disconnect existing wires from lamp holder terminals to make new connections at the lamp holder terminals.
- Instead, installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to the lamp holder lead wires by employing applicable connectors.
- Install this kit only in the luminaries that have the construction feature and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- FOR RETROFIT KITS CERTIFIED TO CANADIAN REQUIREMENTS: THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JUSRISICTION.
- PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN BY THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES. THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS.
- LED retrofit kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Luminaire wiring and electrical parts may be damaged when drilling for the installation of an LED retrofit kit. Check for enclosed wiring and components.
- The retrofit position is located at the edge of the target luminaire with installed max of four LED tubes. LED tubes manufactured by PRECISION LIGHTING & TRANFORMER INC, model PL TSP3E21X.
- This kit is intended to retrofit target luminaires with the following characteristics:
- Surface-mounted, Type IC, or Type non-IC recessed-mounted
- With or without a diffuser
- Not dimmable
- Max 4 LED tubes which are manufactured by PRECISION LIGHTING & TRANSFORMER INC (E4790302), Model PLTSP2E21X
- The retrofit position is located at the edge of the four LED tubes
- One single branch circuit as power supply connection
- Refer to the below table for Min compartment dimensions
- Max. mounting height: 8.07′
| Model Number | MINIMUM LAMP COMPARTMENT DIMENSIOINS [length X width X height] | |
| Target Luminaire | PLTSP3P417 | 47.83×23.82×2.95in 1215x605x75mm |
Installation Instructions
- Turn the DIP switch on the B side to the “ON” position.
- Combine the adapter and the end cap of B side.
- Disconnect power to the fixture.
- Remove existing tubes, reflector, and grille, and remove the lamp housing.
- Open the Test Switch hole on the side of the fixture.
- Install the external test switch.
- Connect the AC terminal wire (Black, White, Red) in the accessory box to the junction box.
- Install the lamp housing, reflector, and existing tubes.
- Install the emergency LED lamp.
- AC & test switch terminal male and female are plugged together.
- The AC wire and the test switch wire enter the interior of the fixture.
- Install the fixed clip on the B side.
Wiring Diagram
FCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
WARNING
- Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
- To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
- Proper grounding is required to ensure safety.
- Power must be turned off at the breaker before installation or maintenance.
- This product must be installed per the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Wear gloves and eye protection at all times while installing, servicing, or performing maintenance on the luminaire, and avoid direct eye exposure to the light source while it is on.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- Do not install damaged products. Inspect the luminaire for damage that may have occurred during transit. If damaged, contact the manufacturer immediately.
- These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance.
- Should further information be desired or should particular problems arise that are not covered sufficiently for the purchaser’s or owner’s purposes, contact the manufacturer.
CONTACT INFORMATION
- 972-535-0926
- pltsolutions.com.
- ver 082824
Documents / Resources
 |
PLT PLTSP3P417 LED T8 Tube with Emergency Backup [pdf] Instruction Manual PLTSP3P417 LED T8 Tube with Emergency Backup, PLTSP3P417, LED T8 Tube with Emergency Backup, with Emergency Backup, Emergency Backup, Backup |
