PKM IN5-FZ-2 Induction Hob Instruction Manual

Installation Requirements:
Installation must comply with safety standards, regulations, and norms. Ensure proper ventilation and clearance around the hob.

Cookware Placement:
Do not turn on the hob without placing cookware on it. Keep the hob clean for optimal heating performance.

Cooking Zone Adjustment:
The cooking zones adjust automatically to the size of the pan up to a certain limit. For best results, center the pan on the cooking zone.

Operating Instructions:

Turning On: Slide the control to the desired power level. The hob indicator will blink after 5 seconds of inactivity.

Turning Off: Slide the control to 0 to turn off a heating zone. The hob enters standby mode after 1 minute of inactivity at power level 0.
Boost Function: Activate or deactivate the boost function as needed.

FAQ

FAQ Section:

How do I activate the boost function?
To activate the boost function, press the Boost button on the control panel.

What should I do if there is a technical malfunction?
If there is a technical malfunction, contact authorized technicians for assistance.

Dear customer! We would like to thank you for purchasing a product from our wide range of domestic appliances. Read the complete instruction manual before you operate the appliance for the first time. Retain this instruction manual in a safe place for future reference. If you transfer the appliance to a third party, also hand over this instruction manual.

Do not dispose of this appliance together with your domestic waste. The appliance must be disposed of at a collecting center for recyclable electric and electronic appliances. Do not remove the symbol from the appliance.

The figures in this instruction manual may differ in some details from the current design of your appliance. Nevertheless, follow the instructions in such a case.

Any modifications, which do not influence the functions of the appliance. shall remain reserved by the manufacturer. Please dispose of the packing with respect to your current local and municipal regulations.
The appliance you have purchased may be an enhanced version of the unit this manual was printed for. Nevertheless, the functions and operating conditions are identical. This manual is therefore still valid. Technical modifications as well as misprints shall remain reserved.

EU – DECLARATION OF CONFORMITY

The products, which are described in this instruction manual, comply with the harmonized regulations.

The relevant documents can be requested from the final retailer by the competent authorities.

Safety information

READ THE SAFETY INFORMATION AND SAFETY INSTRUCTIONS CAREFULLY BEFORE YOU OPERATE THE APPLIANCE FOR THE FIRST TIME.
All information included in those pages serve for the protection of the operator. If you ignore the safety information and safety instructions, you will endanger your health and life.

Store this manual in a safe place so you can use it whenever it is needed.
Strictly observe the instructions to avoid damage to persons and property.
Check the technical periphery of the appliance! Do all wires and connections to the appliance work properly? Or are they time-worn and do not match the technical requirements of the appliance? A check-up of existing and newly made connections must be done by an authorized professional. All connections and energy-leading components (incl. wires inside a wall) must be checked by a qualified professional. All modifications to the electrical mains to enable the installation of the appliance must be performed by a qualified professional.

The appliance is intended for private use only.
The appliance is intended for cooking in a private household only.

The appliance can be used with 230 V AC in RVs/caravans when built in according to all TÜV-regulations.
The appliance is intended for indoor use only.
The appliance is not intended to be operated for commercial purposes and in public transport.
Operate the appliance in accordance with its intended use only.
Do not allow anybody who is not familiar with this instruction manual to operate the appliance.
This appliance may be operated by children aged from 8 years and above as well as by persons with reduced physical, sensory and mental capabilities or lack of experience and
knowledge if they are supervised or have been instructed concerning the safe use of the appliance and do comprehend the hazards involved. Children must not play with the appliance.
Cleaning and user maintenance must not be carried out by children unless they are supervised.

MAKE SURE THAT THIS MANUAL IS AVAILABLE TO ANYONE USING THE APPLIANCE AND MAKE SURE THAT IT HAS BEEN READ AND UNDERSTOOD PRIOR TO USING THE APPLIANCE.

IMPORTANT INFORMATION FOR PERSONS WITH A PACEMAKER OR ANY OTHER MEDICAL IMPLANT:

The appliance complies with the current electromagnetic interference regulations. It fully complies with all legal requirements (2004/108/EG). It designed to not interfere with the functions of other electric appliances, provided they comply with identical regulations. DANGER! THIS INDUCTION HOB GENERATES A MAGNETIC FIELDS IN ITS IMMEDIATE VICINITY.

Your pacemaker must be designed in compliance with the corresponding regulations so it will not cause any interferences between the pacemaker and the appliance.
Consult the manufacturer of your pacemaker or your doctor to decide whether it meets the forced requirements or if any incompatibilities do exist.

Signal words

indicates a hazardous situation which, if ignored, will result in death or serious injury.

indicates a hazardous situation which, if ignored, could result in death or serious injury.

indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

indicates possible damage to the appliance.

Safety instructions

DANGER

To reduce the risk of electrocution:

Non-compliance of the orders of this instruction manual will endanger the life and health of the operator and / or can result in damages to the appliance.
The appliance must be connected to the mains by a qualified professional, who is familiar with and adheres to the local requirements and supplementary regulations of your energy supplier.
All electrical work must be carried out by a qualified professional. Do not modify the energy supply. The connection must be carried out in accordance with the current local and legal regulations

Do not connect the appliance to the mains if the appliance itself or the power cord or the plug are visibly damaged.
Never try to repair the appliance yourself. Repairs carried out by unauthorized persons can cause serious damage. If the appliance does not operate properly, please contact the shop you purchased the appliance at. Original spare parts should be used only.
When the power cord is damaged, it must be replaced by the manufacturer or an authorized aftersales service or a qualified professional only.

Never touch the power plug, the power switch or other electrical components with wet or damp hands. RISK OF ELECTRIC SHOCK!

WARNING!
To reduce the risk of burns, electrocution, fire or injury to persons:

Operate the appliance with 220 ~ 240 V AC / 50 Hz only.

Disconnect the appliance from the mains before you clean or maintain it.
The technical data of your energy supply must meet the data on the rating label. The main current circuit must be equipped with a safety shut-down device.
The appliance must always be grounded and protected corresponding to the requirements of your local energy supplier. The main current circuit must be equipped with a safety shut-down device.

All modifications to the electrical mains to enable the installation of the appliance must be performed by a qualified professional.
In case of an event caused by a technical malfunction, disconnect the appliance from the mains. Report the malfunction to your service centre so it can be repaired.
If any cracks occur on the glass-ceramic , switch off the appliance and disconnect it from the mains. RISK OF ELECTRICAL SHOCK!

Do not use adapters, multiple sockets and extension cords for connecting the appliance to the mains.
Do not carry out any modifications to your appliance.
Do not repair the appliance yourself. Repairs carried out by unauthorized persons can cause serious damage. Always contact the nearest service centre. Only original spare-parts should be used for repairs.

The room the appliance is installed in must be dry and well-ventilated. When the appliance is installed, an easy access to all control elements is required.
The veneering of cabinets has to be fixed with a heat-resistant glue, that is able to withstand a temperature of 100 0C.
Adjacent furniture or housing and all materials used for installation must be able to resist a temperature of min. 85 0C above the ambient temperature of the room the appliance is installed in during operation.

Do not install the appliance in rooms or at areas which contain flammable substances as petrol, gas or paint. This warning also refers to the vapour these substances release.
Cooker-hoods should be installed according to their manufacturers’ instructions.
The safety distance between the hob and a wall/cupboard above should be at least 450 mm.

The safety distance between the hob and an extractor hood above should be at least 650 mm.
Unattended cooking with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.
Do not install the appliance near to curtains or upholstered furniture. RISK OF FIRE!

Do not store any objects on the hob. RISK OF FIRE!
Household equipment and connection leads must not touch the hob as the insulation material is usually not heat-resistant.
Never use a steam cleaner to clean the appliance. The steam will cause serious damage to the electric components of the appliance. RISK OF ELECTRICAL SHOCK!

Never touch the cooking zones while the residual heat indicator is still on. RISK OF BURNS!
After use, always switch off the cooking zones as described in this manual (i.e.by using the touch controls). Do not rely on the auto-detection feature to switch off the cooking zones when you remove the cookware.
The appliance is not allowed to be operated with an external timer or a separate remote-control system.

The accessible parts of the appliance become hot during operation, so keep children away from the operating appliance. Touching the appliance while it is operating can cause serious burns.
Children must not play with the appliance.
Always supervise children when they are near the appliance.

This appliance may be operated by children aged from 8 years and above as well as by persons with reduced physical, sensory and mental capabilities or lack of experience and knowledge if they are supervised or have been instructed concerning the safe use of the appliance and do comprehend the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be carried out by children unless they are supervised.
Only allow children to use the appliance without supervision, when adequate instructions have been given before so that the child is able to use the appliance in a safe way and understands the risks of improper use.
While unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept away from children and pets. RISK OF INJURY! CHOKING HAZARD!

Only use hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

CAUTION!

Do not use any aggressive, abrasive and acrid detergents or sharp-edged items to clean the appliance. Otherwise you may scratch the surface and damage the glass.

Do not switch on the hob before you have put a cookware on it.
The hob should be clean at every time. Soiled cooking zones do not transfer the heat correctly.
Protect the hob against corrosion.

Switch off soiled cooking zones.
Switch off the complete hob if any damage or malfunction occurs.
Do not leave pans with prepared dishes based on fats and oils unattended on a operating cooking zone; hot fat can spontaneously catch fire.

The blades of scrapers for cleaning an induction hob are very sharp. Do not cut yourself, especially when you have removed the safety cover of the scraper.
Metal-made items such as knives, forks, spoons and pan lids should not be put on the appliance, because they may become hot.
This appliance complies with the current European safety legislation. We do wish to emphasize that this compliance does not negate the fact that the surfaces of the appliance will become hot while operating and will retain and emit heat even if it has stopped operating.

NOTICE!

When you move the appliance, hold it at its base and lift it carefully. Keep the appliance in an upright position.
The appliance must be transported and installed by at least two persons.

When you unpack the appliance, you should take note of the position of its components in case you have to repack and transport it at a later point of time.
Do not put any heavy items on the hob.
Only use cookware which is suitable to be used on ceramic glass; otherwise you will damage the appliance.

Do not operate the appliance unless all components are installed properly.
The air vents of the appliance or its built-in structure (if the appliance is suitable for being built-in) must be completely open, unblocked and free of any kind of dirt.
The rating plate must not be removed or made illegible, otherwise all terms of the warranty become invalid!

SAVE THESE INSTRUCTIONS.

The manufacturer and distributor are not responsible for any damage or injury in the event of failure to comply with these instructions.

Installation

DANGER!

The appliance must be connected to the mains by a qualified professional, who is familiar with and adheres to the local requirements and supplementary regulations of your electricity supplier. Do not carry out the installation yourself. RISK OF ELECTRIC SHOCK!
All electrical work must be carried out by a qualified professional. Do not modify the energy supply. The connection must be carried out in accordance with the current local and legal regulations. RISK OF ELECTRIC SHOCK!
The safety distance between the hob and a wall cupboard above should be at least 450 mm.

WARNING
The safety distance between the hob and an extractor hood above should be at least 650 mm.

CAUTION!

Do not install the appliance above cooling equipment, dish washers or laundry dryers.

When installing the appliance ensure optimal heat radiation to maintain the operating safety.
The wall and the reach of the heat radiation above the worktop must be made of heat-resistant materials.
To avoid any damage, the sandwich layer and adhesive must resist heat.

Unpacking and positioning

Unpack the appliance carefully. Dispose of the packaging as described in chapter WASTE MANAGEMENT.
The appliance may be equipped with the transport-protection. Be very careful and do not use any aggressive or abrasive detergents to remove residuals of the transport-protection.

Check that the appliance and the power cord are not damaged.
Connect the appliance to a dedicated socket only.
Do not install the appliance in a place where it may come in contact with water or rain; otherwise the insulation of the electrical system will be damaged.

Connect the appliance to the mains properly.

Pre-installation requirements

The worktop must be rectangular and plane and made of heat-resisting material. Structural elements should not interfere with the installation area.

The installation must meet the safety requirements as well as the legal rules and regulations.
The wall sat the hob should be covered with heat-resistant material, e.g. ceramic tiles.
The power cable must not come into contact with cabinet doors or drawers.

The appliance must be supplied with an adequate flow of fresh air from outside the cabinet to the base of the hob.
If the hob is installed above an oven, the oven must be equipped with a cooling system.
Install a thermal protection below the bottom of the appliance when installing it above a drawer or a cupboard.

The circuit breaker must be easily accessible.

Installation Instructions

Selection of installation equipment
Theappliance must be installed and connected in accordance with current regulations.
After unpacking the appliance, ensure there is no visible damage. If it has been damaged during transit, DONOTUSE, contact where you buy immediately.

Selection of installation equipment

Cut out the work surface according to the sizes shown in the drawing.
For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30mm. Please select heat-resistant work surface material to avoid larger deformation caused by the heat radiation from the hotplate. As shown below (measure by unit: mm):

L (mm)	W (mm)	H (mm)	D (mm)	A (mm)	B (mm)	X (mm)
770	520	60	56	750+5 -0	490+5 -0	50 mini

Under any circumstances, make sure the electric hob is well ventilated and the air inlet and outlet are not blocked. Ensure the electric hob is in good work state. As shown below:

Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 760mm.

A(mm)	B(mm)	C(mm)	D	E
760min	50min	20min	Air intake	Air exit 50mm

Make sure the induction cooker hob is well ventilated and that air inlet and outlet are not blocked. In order to avoid accidental touch with the overheating bottom of the hob, or getting un-expectable electric shock during working, it is necessary to put a wooden insert, fixed by screws, at a minimum distance of 50mm from the bottom of the hob. Follow the requirements below:

There are ventilation holes around outside of the hob. YOU MUST ensure these holes are not blocked by the worktop when you put the hob into position.
Be aware that the glue that join the plastic or wooden material to the furniture, has to resist to temperature not below 150℃, to avoid the unstuck of the paneling.

The rear wall, adjacent and surrounding surfaces must therefore be able to withstand an temperature of 90℃.

The induction hotplate must be installed by qualified personnel or technicians. We have professionals at your service. Please never conduct the operation by yourself.

The hob will not be installed directly above a dishwasher, fridge, freezer washing machine or clothes dryer, as the humidity may damage the hob electronics.
The induction hotplate shall be installed such that better heat radiation can be ensured to enhance its reliability.
The wall and induced heating zone above the table surface shall withstand heat.

To avoid any damage, the sandwich layer and adhesive must be resistant to heat.
A steam cleaner is not to be used.

Connecting the hob to the mains power supply
This hob must be connected to the mains power supply only by a suitably qualified person
Before connecting the hob to the mains power supply, check that:

The domestic wiring system is suitable for the power draw by the hob.
The voltage corresponds to the value given in the rating plate.
The power supply cable sections can withstand the load specified on the rating plate. To connect the hob to the mains power supply, do not use adapters, reducers, or branching devices, as they can cause overheating and fire. The power supply cable must not touch any hot parts and must be positioned so that its temperature will not exceed 75℃ at any point.

Check with an electrician whether the domestic wiring system is suitable without alterations.
Any alterations must only be made by a qualified electrician.

If the cable is damaged or to be replaced, the operation must be carried out by after-sale agent with dedicated tools to avoid any accidents.
If the appliance is being connected directly to the mains an omnipolar circuit- breaker must be installed with a minimum opening of 3mm between contacts.
The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorised technicians only.

Product Instruction

Top View

Sepecifications

Model No	Rating (Rated voltage/voltage range/ Rated Power)
IN5-FZF	220-240V~, 50-60Hz, 10000W

Control Panel
5 burner induction hob:

Button Instruction

Production Operation

Control touch

The controls can sense touch, so you don’t need to apply any pressure.
Use the finger, instead of the nail to operate it.
Each time a touch is sensed, you will hear a “beep” sound.
Make sure the control area are always clean, dry, and there is no object (e.g. a utensil or a cloth) covering them. Even a thin film of water may make it hard to control.

Choose the right Cookware

Only use cookware with a base suitable for induction cooking. Look for the induction symbol on the packaging or on the bottom of the pan/pot.
You can check whether your cookware is suitable for the induction hob by carrying out a magnet test. Move a magnet towards the base of the pan/pot. If it is attracted, the pan/pot is suitable for induction hob.
If you do not have a magnet:
- 3. Put some water in the pan/pot you want to check.
- 4. If does not flash in the display and water is being heated, the pan/pot is suitable.
Cookware made from the following materials is not suitable for an induction hob: pure stainless steel, aluminum or copper pan/pot without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan/pot is smooth, sits flat against the crystal plate, and is the same diameter as the cooking zone. If use the bigger pan/pot, the hob will work with maximum efficiency. If use smaller pan/pot, efficiency could be less than expected. The hob may can’t detect
pan/pot with diameter less than 140mm. Always place your pan/pot on the center of cooking zone.
Always lift pan/pot off the hob – do not slide pan/pot on the crystal plate, or they may scratch the plate.

Suggested Pan dimensions for induction hob
The cooking zones are, up to a limit, automatically adapted to the diameter of the the pan. However, it is suggested that the bottom of this pan have a diameter minimum according to the corresponding cooking zone. To obtain the best performance from your hob, please place the pan in the center of the cooking zone.

Base diameter of the pots:

Cooking zone	Minimum (mm)	Maximum (mm)
180mm	Ф140	Ф180
260mm	Ф200	Ф280
FLEX	Ф200	385*200

Operation Instructions

Turn on

Turn off

Boost

Boost mode just can keep 5 minutes. After 5 minutes, the cooking zone returns to its original setting.
If original heat setting equals “0”, it will return to “9” level after 5 minutes.

Child Lock

You can press the child lock button “Lock” to freeze other function, to avoid accident,.(For example, a child accidentally turns on the heating zone)
Under “Child lock” mode, only “On/Off” and “Loc”k button can work.

Lock
Touch the “lock” control	Display will show “Lo”.
Unlock
If the induction cooker is locked, touch and hold “Lock” , the cooker will exit the locked state and you will hear a ”beep “.

You can always use the “on / off” button to turn off the induction cooker in an emergency, but in the next operation, you should first unlock the induction cooker.

FLEX function
You can use two cooking zones by selecting the “FLEX DUO” function and let them keep the same power by covering the whole surface with a large pan or partly with a round / oval pan. When the function is turn on and only one pan is used, the pan can be moved throughout the area. In this case, the slider can be used to control two cooker on the same side without difference.

It is very suitable for cooking with oval or rectangular pan or with pan supports.
If need to turn off this function, please press the “FLEX DUO” button.

Important: Place the pan in the center of the cooking area, so that it covers at least one reference point (as shown below).

Pause
Press the “pause” button in the working state, the cooker will enter the pause state, and the display will show respectively. To cancel the pause function, press the “pause” button again, and the cooker will return to its previous working state.
If there is no operation within 10 minutes in the pause state, the cooker will automatically turn off.

Keep warm
Select the heating area, press the “keep warm” button, the heating area will enter the heat preservation cooking mode, and the display will show “” ,the induction cooker will heat with low power to maintain the proper temperature of the pot.
The power is not adjustable under this function.

Timer
You can use timer function by below two ways:

You can use it as a minute reminder. In this case, the timer will not close any cooking area at the set time.
You can also set it to turn off one or more heating zones after the setting time

When a heating zone is set a timer and the heating time reaches the set timer, the heating zone automatically sets the power level to 0, and the power output is turned off.

The above pictures are for reference only, subject to the final product.

Timed reminder
In the working state, if no heating zone is selected, press the timing function button to set time and start the time reminder function. When the set time is reached, the buzzer will sound a warning for 30S.
The timing time can be adjusted to “0” to exit the timing reminder function.

In the timing state, if you press the heating area selection button to select the hob, the current display time is the timing of the currently selected hob.
The display time shows one of the four timers, the decimal point of the single digit display of the corresponding zone will flash. It means the time currently displayed is the timing time of the area.
If all of the decimal point of single digit does not flash, it means that the current two digits display is the time of the timing reminder.

Default working time
Auto shutdown is the safety protection function of induction cooker. This occurs whenever you forget to switch off a cooking zone. The default shutdown times as below table:

Power level	1	2	3	4	5	6	7	8	9
Default working timer (hour)	8	4	4	4	2	2	2	2	2

The display will stop heating immediately when cookers are moved away, and auto turn off after 2 minutes.
If there are multiple heating areas heating at the same time, the default timing of the whole machine is the one with the longest default timing time.

Heat Settings

The settings below are guidelines only. The exact setting will depend on factors including your cookware and the amount you are cooking. Experiment with the hob to find the settings that best suit you.

Heat setting	Suitability
1 – 2	• delicate warming for small amounts of food • melting chocolate, butter, and foods that burn quickly • gentle simmering • slow warming
3 – 4	• reheating • rapid simmering • cooking rice
5 – 6	• pancakes
7 – 8	• sautéing • cooking pasta
9	• stir-frying • searing • bringing soup to the boil • boiling water

Cleaning and Maintenance

Important: Before any maintenance or cleaning work is carried out, disconnect the appliance from electricity supply and ensure the appliances is completely cool. Cleaning the Hob Surface
Clean spillages from the hob surface as soon as possible after use. Always ensure the surface is cool enough before cleaning.
Use a soft cloth or kitchen paper to clean the surface. If the spillage has dried on the surface, you may need to use a specialist vitro-ceramic glass cleaner, which is available for most of supermarkets.

Do not use other abrasive cleaners and/or wire wool ect., as it may scratch the ceramic glass surface of your hob.

Failure Inspection for induction hob

Problem code and solution

Failure code	Problem	Solution
E7	Supply voltage is below the rated voltage	Please inspect whether power supply is normal. Power on after the power supply is normal.
E8	Supply voltage is above the rated voltage
E3	The surface sensor high temperature	Wait for the temperature of ceramic plate return to normal. Touch “ON/OFF” button to restart unit.
E6	High temperature of IGBT	Wait for the temperature of ceramic plate return to normal. Touch “ON/OFF” button to restart unit. Check whether the fan runs smoothly;if not, replace the fan.
E1	The surface sensor disconnection	Check the connection or replace the ceramic plate temperature sensor.
E2	The surface sensor short circuit
Eb	The surface sensor failure
E5	IGBT sensor short circuit	Replacd the drive board.
E4	IGBT sensor open circuit	Replacd the drive board.

Specific faults and Solutions

Failure	Cause	Want to do
LED does not light up when the device is plugged in	No electricity in the socket	Check that the plug is firmly fixed to the socket and that the socket is working
	Failed to connect power board and display board	Check the connection
	Power board damaged	Replace the power board
	Display board damaged	Replace the display board
Some buttons do not work, or LED display is not normal	The display board is damaged	Replace the display board
The Cooking mode indicator comes on, but heating is not started	High temperature of the hob	The ambient temperature may be too high and the air inlet or vent may be blocked
	Something wrong with the fan	Check whether the fan operates normally. If not, replace the fan.
	Power board damaged	Replace the power board
During the operation, the heating stops suddenly and the display flashes “U”	Wrong pot type	Use a suitable pan (refer to the manual); Pot detection circuit damage,replace the power board.
	The diameter of the bottom of the pot is too small
	Pot overheated	Wait for the temperature to return to normal; Press the “on / off” button to restart the device
“U” is displayed in the heating area on the same side (such as the first and second areas)	Power board and display board connection failure	Check the connection
	The communication part of the display board is damaged	Replace the display board
	Power board damaged	Replace the power board
Fan motor sounds abnormal	The fan motor is damaged	Replace fan

The above is the common fault judgment and inspection.
Please do not disassemble the equipment by yourself, so as to avoid any danger and damage to the induction cooker.

Waste management:

DISPOSAL: Do not

dispose this product as unsorted municipal waste.

Collection of such waste separately for special treatment

is necessary.

This appliance is labeled in compliance with European directive 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is disposed of correctly, you will help prevent any possible damage to the environment and to human health, which might otherwise be caused if it were disposed of in the wrong way.

The symbol on the product indicates that it may not be treated as normal household waste. It should be taken to a collection point for the recycling of electrical and electronic goods.

This appliance requires specialist waste disposal. For further information regarding the treatment, recover and recycling of this product please contact your local council, your household waste disposal service, or the shop where you purchased it.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

While unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept away from children and pets. CHOKING HAZARD!
Old and unused appliances must be send for disposal to the responsible recycling centre. Never expose to open flames.
Before you dispose of an old appliance, render it inoperative. Unplug the appliance and cut off the entire power cord. Dispose of the power cord and the plug immediately.
Dispose of any paper and cardboard into the corresponding containers.
Dispose of any plastics into the corresponding containers.
If suitable containers are not available at your residential area, dispose of these materials at a suitable municipal collection point for waste-recycling.
Receive more detailed information from your retailer or your municipal facilities.

Materials marked with this symbol are recyclable.

Please contact your local authorities to receive further information.

Guarantee conditions:
This appliance includes a 24-month guarantee for the consumer given by the manufacturer, dated from the day of purchase, referring to its flawless material-components and its faultless fabrication. The consumer is accredited with both the dues of the guarantee given by the manufacturer and the vendor’s guarantees. These are not restricted to the manufacturer’s guarantee. Any guarantee claim has to be made immediately after the detection and within 24 months after the delivery to the first ultimate vendee. The guarantee claim has to be verified by the vendee by submitting a proof of purchase including the date of purchase and/or the date of delivery. The guarantee does not establish any entitlement to withdraw from the purchase contract or for a price reduction. Replaced components or exchanged appliances demise to us as our property.

The guarantee claim does not cover:

fragile components as plastic, glass or bulbs;
minor modifications of the PKM-products concerning their authorized condition if they do not influence the utility value of the product;
damage caused by handling errors or false operation;
damage caused by aggressive environmental conditions, chemicals, detergents;
damage caused by non-professional installation and haulage;
damage caused by non common household use;
damages which have been caused outside the appliance by a PKM-product unless a liability is forced by legal regulations.

The validity of the guarantee will be terminated if:

the prescriptions of the installation and operation of the appliance are not observed.
the appliance is repaired by a non-professional.
the appliance is damaged by the vendor, the installer or a third party.
the installation or the start-up is performed inappropriately.
the maintenance is inadequately or incorrectly performed.
the appliance is not used for its intended purpose.
the appliance is damaged by force majeur or natural disasters, including, but with not being limited to fires or explosions.

The guarantee claims neither extend the guarantee period nor initiate a new guarantee period. The geographical scope of the guarantee is limited with respect to appliances, which are purchased and used in Germany, Austria, Belgium, Luxembourg and the Netherlands.

SERVICE INFORMATION

TECHNOLOGY FOR DOMESTIC USE

Aftersales service information on the leaflet inside this instruction manual.

Subject to alterations

Updated
08/26/2024

Documents / Resources

PKM IN5-FZ-2 Induction Hob [pdf] Instruction Manual
IN5-FZ-2, IN5-FZF, IN5-FZ-2 Induction Hob, IN5-FZ-2, Induction Hob, Hob

References

User Manual

PKM IN5-FZ-2 Induction Hob

Product Information

FAQ