PIZZELLO Rectangular Dining Table Instruction Manual

Step 1: Connect panel E and panel D using screw G and nut N. Ensure correct connection by checking for 4 silver screw heads in the middle of the table.
Step 2: Assemble parts C, Cupright, F, and L screws as instructed.
Step 3: Continue assembling part F with part B using L screws.
Step 4: Attach the connected B and C parts to the tabletop using screw J.
Step 5: Connect part A with parts B and C using screws J and H. Secure with screw H from the inside.

Patio Bistro Chair

Follow the labeled legs for the front side indication
Assemble on a flat surface to avoid scratches
Do not dispose of the original box until you confirm the product
Contact after-sales service for product return

INTRODUCTION

Thank you for choosing our rectangular dining table! This table is designed for durability, weather resistance, and low maintenance, making it a great addition to both indoor and outdoor spaces.
To ensure long-lasting use and maintain its quality, please read and follow the usage precautions below.

Usage Precautions

ATTENTION

Heat Resistance: The table can withstand temperatures between -104℉ to -140℉ (-40℃to -60℃）. Avoid placing high-temperature objects (such as grills or hot pots) directly on the surface to prevent damage. Using heat-resistant mats is recommended.
Avoid Prolonged Sun Exposure: While our table is weather-resistant, extended exposure to strong sunlight may cause fading or slight warping. Covering the table with a cloth or protective cover when not in use is advised.
Prevent Scratches: Avoid using sharp objects such as knives directly on the table surface to prevent scratches.

TOOLS REQUIRED

ASSEMBLY REQUIREMENT

PARTS LIST

ASSEMBLY INSTRUCTION

Step 1
- Use screw G and nut N to connect panel E and panel D.
- Note: If part E is correctly connected, you will see the 4 silver screw heads in the middle of the table.
- Please check it before installing.
- A) If part E is correctly connected, you will see the 4 silver screw heads in the middle of the table.
- B) If part E is incorrectly connected, you will see the 4 silver screw heads on the side of the table, and you will have a problem on the next step.
Step 2
1. Stand parts C and Cupright at a 90-degree angle to the ground or easier installation.
2. Insert one end of part F into part C, align the holes, and secure it with two L screws.
Step 3
- Insert the other end of part F into part B, align the holes, and secure it with two L screws
Step 4
- Attach the connected B and C parts to the tabletop using screw J.
Step 5
- Use screws J and H to connect part 2 (A) parts with parts B and C.
- (Secure with screw H from the inside)
- Secure with screw H from the inside

PATIO BISTRO CHAIR

Dear Customer,

Thank you for choosing our product. Please read this manual carefully before assembling or using the product, to avoid damage caused by improper use.
If the product is passed on to third parties, this manual has to be passed on along with the product. For any questions, don’t hesitate to contact us.

TOOLS REQUIRED

ASSEMBLY REQUIREMENT

PART LIST

Fasten screws loosely during initial assembly. Do not ﬁrmly tighten screws until step 7.

Assembly Instructions

Tips: We have labeled the legs to indicate which side is the front side.
However, the factory sometimes mislabeled them. Please check with the picture before installing; the straighter side should be the front side.

ATTENTION

When installing, we suggest you can assemble the product on the ﬂat carton which comes with the product, or any other clean ﬂoor to avoid the product surface being scratched.
Please do not dispose of the original product box until you conﬁrm you received the complete and correct item.
If you want to return the product, you are suggested to contact our after-sales service ﬁrst. You need to pack the returned product with the original box and then follow the steps to return it.
Step 1: Connect the beam (E) and the left front leg (A). Use the screw (G) and nut (F) to connect them.
Please don’t tighten the screws yet.
Step 2: Connect the beam (E) andthe Right Front Leg (B). Use the screw (G) and nut (F) to connect them.
Please don’t tighten the screws yet.
Step 3: Attach the chair seat (C) to the Left Front Leg (A) and the Right Front Leg (B).
Please make sure you attach the seat from the correct direction.
Step 4: Use the 4 scresw (G) and 4 nuts (F) to connect them.
Step 5: Remove the 2 protective cases on the seat (C).
Step 6: Assert the seat back (D) to the seat (C).
Step 7: Tighten all the screws and nuts.

How To Replace The Back And Seat

A: Slowly take apart the back of the back frame.
B) Slowly take apart the seat from the seat frame.
Note: When replacing the new seat and back, make sure you assemble them from the correct direction. The edge with round angle should face outside.

FAQ

Can I use the dining table outdoors?

Yes, the table is designed for both indoor and outdoor use. It is weather-resistant.

What is the weight capacity of the patio bistro chair?

The chair has a weight capacity of 265 lbs.

Documents / Resources

PIZZELLO Rectangular Dining Table [pdf] Instruction Manual
Rectangular Dining Table, Rectangular Table, Dining Table

References

User Manual

PIZZELLO Rectangular Dining Table

Specifications

Product Usage Instructions

Parts List:

Tools Required: