Nova PlusNova Plus
LUXX · LUXX CUP · LUXX +
USER MANUAL
OVERVIEW
Description of the product
The Nova Plus Luxx family are products intented to light up during events by receiving PixMob signals and interact with the user through buttons.
Symbols used in this manual
WARNING
Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material or environmental damage.
ELECTRICAL SAFETY HAZARD
READ BEFORE PROCEEDING
LASER SAFETY HAZARD
DO NOT PROCEED IF CONDITION NOT MET
TECHNICAL DATA
 |
 |
 |
|
| Model | NOVA PLUS LUXX STANDARD | NOVA PLUS LUXX CUP | NOVA PLUS LUXX PLUS |
| Description | LED Armrest | LED Armrest | LED Armrest |
| Dimensions | 290mm x 58mm x 122mm | 170mm x 65mm x 24mm | 364mm x 121mm x 91mm |
| Weight | 1.2kg/42.3 oz | 1.3kg/46 oz | 900g/31.8 oz |
| Certification Laser Warning Logotype |
FCC  |
FCC |
FCC |
| Laser Specifications | 650 nm <5mW Class 3R |
650 nm <5mW Class 3R |
650 nm <5mW Class 3R |
| Brightness | RGB LED | RGB LED | RGB LED |
| Data Connector | Cat5E/RJ45 | Cat5E/RJ45 | Cat5E/RJ45 |
| Operating Temp | 0° to 45° C / 32° to 113° F | 0° to 45° C / 32° to 113° F | 0° to 45° C / 32° to 113° F |
| Input Voltage | 10.8-13.2 V DC | 10.8-13.2 V DC | 10.8-13.2 V DC |
| Origin | Designed in Canada Made in China |
Designed in Canada Made in China |
Designed in Canada Made in China |
SECTION 1: SAFETY
Electrical Safety
Access to the internal components is not necessary during normal operation.
Under no circumstance is it required to open the enclosures.
If a unit is suspected of requiring service, contact the manufacturer.
 |
• Do not open the enclosures • Do not tamper with power supply lead |
|
• The device shall be powered by 12VDC ±10% input voltage • The device shall consume a maximum power of 20W |
Prohibited use
- Using the product without instruction
- Removal of explanatory and hazard labels
- Opening of the equipment by using tools (screwdrivers, etc.)
- Using outside the stated limits
- Deactivation of safety systems
- Use of accessories from other manufacturers without approval
- Carrying out modiication or conversion of the product
Safety Notice & Regulatory Compliance
Hazards in use
WARNING
Never attempt to repair the product yourself. In case of damage, contact PixMob.
CAUTION
Changes or modiications not expressly approved by PixMob could void the user’s authority to operate the equipment.
Disclaimer
All maintenance excluding routine cleaning must be performed by PixMob or trained personel. No Maintenance or Service is required or allowed by the user.
The device contains no user serviceable parts. Do not attempt to disassemble the assembly and/or components. The laser head is sealed and should not be opened for any reason. If service or maintenance are determined to be needed, remove the Nova Pro Luxx product and contact PixMob for shipping instructions.
Operator Instructions
Only board operators trained and approved by PixMob may control the Nova Pro Luxx Family.
Compliance Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction
This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penaltie
Nameplate
Labelling
| Nova Plus – LUXX Standard (Right) | Nova Plus – LUXX Standard (Left) |
 |
 |
| Nova Plus – LUXX CUP (Right) | Nova Plus – LUXX Standard (Left) |
 |
 |
| Nova Plus – LUXX PLUS (Right) | Nova Plus – LUXX PLUS (Left) |
 |
 |
SECTION 2: MAINTENANCE
Luxx Family Care Instructions
Only cleaning products approved by the manufacturer should be used during routine cleaning of the Luxx Family products. A list of products that can cause damage includes, but is not limited to :
- Acetone (nail polish remover and other products containing acetone)
- Propylene Glycol
- Threadlocking products
- Other ammonia-based products & solvents
Maintenance Guidelines
- Use only a soft, lint-free cloth
- Clean the device with a damp, soft cloth
- Avoid abrasive cloths, towels, paper towels, or similar items
- Never immerse the device in water
- Avoid excessive wiping, which might cause damage
- Don’t use aerosol sprays, bleaches, or abrasives
- Don’t spray cleaners directly onto the item
LUXX CUP & LUXX STANDARD – Removal Instructions
The device contains no user serviceable parts. All maintenance excluding routine cleaning must be performed by PixMob or trained personel.
No Service is required or allowed by the user. In the event where replacement is needed, a trained service technician will remove the armrest.
LUXX PLUS – Removal Instructions
The device contains no user serviceable parts. All maintenance excluding routine cleaning must be performed by PixMob or trained personel.
No Service is required or allowed by the user. In the event where replacement is needed, a trained service technician willl remove the Nova Plus Luxx product.
SECTION 3: SUPPORT
Contact Technical Support
There are no user-serviceable parts inside this product. Should you experience any issue or malfunction with your Nova Plus product, or if your Nova Plus product needs service, please contact the Technical Support Service Team at 514-510-5777 or e-mail us at support@pixmob.com
514-510-5777
support@pixmob.com
Environmental Notice 
By placing the above symbol on our products and accessories, PixMob is indicating that we are committed to helping reduce the amount of waste electronics ending up in municipal landills.
Therefore, PixMob urges customers to recycle this product and its accessories.
PixMob is equipped to recycle any of its electronic products and accessories and will assist our customers with their recycling options.
To arrange for recycling of your PixMob product or accessory, please contact PixMob/ESKI INC. for more information at 514-510-5777 (USA & Canada)
PIXMOB.COM
©2024 PixMob (ESKI INC.)
All Rights Reserved
Documents / Resources
 |
PIXMOB Nova Plus Permanent Crowd Immersive Lighting Solution [pdf] User Manual 2ADS4-LUXXPLUS, 2ADS4LUXXPLUS, Nova Plus Permanent Crowd Immersive Lighting Solution, Nova Plus, Permanent Crowd Immersive Lighting Solution, Crowd Immersive Lighting Solution, Immersive Lighting Solution, Lighting Solution, Solution |