Pipishell-Logo

Pipishell PIFS35G Floating Shelves with Wire Storage Basket

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Product

Tools Needed

Tools Needed (Not Included)

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (1)

Package Contents

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (2) Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (3)

IMPORTANT SAFETY INFORMATION

IMPORTANT! INFORMAZIONI SULLA SICUREZZA

  • Weight Capacity
    Do not exceed weight capacity.Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (4)
  • Check package contents against supplied parts and hardware list to verify that all parts were received and undamaged.
  • Carefully read and follow all instructions. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
  • NOTE: Not all hardware included in this package will be used.

Assembly Instruction

Assemble the Wall Shelf
There are multiple wall shelf configurations.

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (5)

Wire Shelf Configuration

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (6)

Configurations Without Wire Shelf

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (7) Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (8)

  • NOTE: The long side of the metal brackets should connect to the shelf.

Mark Hole Locations 

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (9)

Position the shelf at your desired height and make sure it is level and flush with the wall. Mark the locations where holes will be drilled.

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (10)

NOTE:
The shelf must sit on top of the metal brackets or wire shelf when secured to the wall.

Drill Pilot Holes

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (11)

3A: For Wood Stud Wall

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (12)

3B: For Drywall
Screw the anchor into the drywall. If it is too difficult to screw in, drill a pilot hole, then tap it in to start it.

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (13)

3C: For Solid Concrete
Tap the anchors into the wall so that they are seated flush with the concrete surface.

Attach the Shelves to the Wall 

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (14)

For wire shelf configuration, screw the lag screws into the wall with the screw head protruding 3/16″ (5mm). Hang the shelf, pull it down, then fully tighten the screws.

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (15)

Which Lag Screws Should I Use? 

Wood Studs

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (16)

Drywall and Solid Concrete

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (17)

  • Use long lag screws [C] for wood studs.
  • Use short lag screws [B] for drywall and solid concrete.

Verify Shelves are Firmly Mounted

Pipishell-PIFS35G-Floating-Shelves-with-Wire-Storage-Basket-Fig- (18)

Contact Information

Documents / Resources

Pipishell PIFS35G Floating Shelves with Wire Storage Basket [pdf] Instruction Manual
PIFS35, PIFS35B, PIFS35G, PIFS35G Floating Shelves with Wire Storage Basket, PIFS35G, Floating Shelves with Wire Storage Basket, Shelves with Wire Storage Basket, Wire Storage Basket, Storage Basket

References

Leave a comment

Your email address will not be published. Required fields are marked *