PICO 4 Ultra VR MR Headset User Guide

Avoid using the product in rooms with single-colored walls,
large reflective objects, or moving images/objects.
Remove the protective film from the front cameras of the VR
headset and wear the lanyards connected to the controllers.

Set up your environment by following instructions on the VR
headset screen.

Installing the Batteries:

Pull out the insulation film in the battery case.

Toggle the battery case button to open the case and replace the
batteries with 1.5V AA alkaline batteries.

Powering On:

Controllers: After pulling out the insulation
film, the controllers will automatically power on. Subsequently,
press the Home button on the controller to power it on.

Headset: Long press the POWER button for 3
seconds until the status indicator turns white.

Wearing and Adjusting the Headset:

Wear the headset and adjust it for a comfortable fit by
fine-tuning and tightening the top strap to reduce pressure on your
forehead.

Note: This product does not support vision correction.
If needed, wear glasses or lens inserts while using the
product.

Frequently Asked Questions (FAQ):

Q: Can children use this product unsupervised?

A: No, users aged 13 and over should be
supervised by an adult while using this product to avoid
accidents.

Q: How does the device track movements?

A: The device can track translational and
rotational movements in all directions to replicate movements in
the real world into the virtual world.

“`

View Fullscreen

User Guide

Important Health & Safety Notes

· Please read the Safety and Warranty Guide before using the product.

· This product is designed and intended to be used in an open and safe indoor
area, free of any tripping or slipping hazards. To avoid accidents, remain con-
scious to the potential confines of your physical area and respect the boundary of your virtual area whenever you see it. Be sure to wear the lanyards when
using the Controllers. Make sure that there is enough space around your head and body (at least 2 meters by 2 meters) to stretch your arms to avoid damage or injury to yourself, others, and your surroundings.

· Children aged 12 or younger are not recommended to use this product. Keep

the headset, controllers and accessories out of children’s reach. To avoid acci-

dents, users aged 13 and over should be supervised by an adult while using this

product.

· This product does not support vision correction. If you need vision correction, keep your glasses on while using the product and take care not to scratch your glasses on the headset lenses.Take care to protect the optical lenses from scratches caused by sharp objects. Use a soft eyeglasses cloth to clean the lens-
es and avoid causing scratches that may affect the viewing experience.

· Extended periods of use may cause slight dizziness or eyestrain. Take a break after 30 minutes and do eye exercises or look into the distance to relieve eyestrain. Stop using the product immediately if you experience any discomfort. If the discomfort persists, consult a doctor.

· Exposing the headset to direct sunlight or ultraviolet light (in outdoor environments, cars, on balconies, or windowsills) may result in permanent yellow spots on the display. Damage of this nature is not covered by the product warranty.

· You can adjust the pupil distance in “System Settings”. However, note that the

headset may come into contact with your nose bridge if the pupil distance is set to the minimum value.With the headset on, you can go to “Settings” “Display” to adjust the pupil distance manually. Note that improper pupil distance may result in double vision or eyestrain. · This product comes with an “Eye Protection Mode”, which passes the Low Blue Light certification by TÜV SÜD (Germany). It uses software algorithms to reduce the amount of blue light in the three-color channel and protect your eyes. Images will appear yellowish in this mode. You can go to “Settings” “Display” “Color” “Eye Protection” to turn this feature on or off.
* Product and packaging are updated regularly, and the functions and contents of the standalone headset may be upgraded in the future. Therefore, the content, appearance and functionality listed in this manual and product packaging are subject to change and may not reflect the final product. These instructions are for reference only.
* Carefully read this user guide before using the product and share this information with any other users, as it contains important safety information. Keep the user guide as reference for the future.

6 Degrees of Freedom VR

The device can track your translational and rotational movements in all directions

(up/down, left/right,forward/backward, pitch, roll, and yaw). Your movements in

the real world will be captured and translated to what you see in the virtual world

when using the appropriate content.

The product does not have any cables, so make sure you are in a safe environment

while exploring the virtual world.

1. Prepare a clean, safe and well lit space of at least 2 × 2 meters. Avoid using the

product in rooms with single-colored walls, large reflective objects (such as glass

panes and mirrors), or moving images/objects.

2. Remove the protective film from the front cameras of the VR headset and wear

the lanyards connected to the controllers.

3. Set up your environment by following instructions on the VR Headset screen.

Installing the battery batteries
Pull out the insulation film in the battery case.

Quick Guide
Toggle the battery case button to open the case and replace the batteries.

2m
2m Note: The “Safety Area” feature of the product cannot guarantee your safety in the set gaming area. Stay alert to any safety risks. 04

Note: 1.5V AA alkaline batteries are recommended.

Power on the controllers
First power-on: After you pull out the insulation film, the controllers will be automatically powered on (with a blue indicator flashing). Subsequent power-ons: Press the “Home” button on the controller to power it on (with a blue indicator flashing).

Power on the headset Long press the POWER button for 3 seconds until the status indicator turns white.

Wear the headset and adjust it to ensure a comfortable fit and view
· Raise the rear part of the head strap and wear the headset. Adjust the headset so that you have a clear, unobstructed view.
· After the headset fits into place, buckle up the rear part of the head strap and tighten the strap dial.

Fine-tune the head strap top strap Fine-tune and tighten the top strap to reduce the pressure on your forehead.

Note: This product does not support vision correction. If you need vision correction, wear your glasses or lens inserts while using this product.
06

Adjust the pupil distance In System Settings, go to “Settings” “Display” to adjust the pupil distance. Tap “+” or “-” to fine-tune the pupil distance until you have a clear view.
EN
64 mm

Product Details
Headset Status Indicator White indicator constant: Powering on or in operation Blue indicator flashing: Powering off Red indicator flashing: Low battery Indicators off: Sleeping or powered off
Charging Status Indicator Charging while powered off Yellow indicator constant: Charging while powered off. Battery level lower than 98% Red indicator constant: Charging. Battery level lower than 20% Green indicator constant: Charging complete. Battery level higher than 98% or full Charging while powered on White indicator constant: Charging while powered on. Battery level lower than 98% Red indicator constant: Charging. Battery level lower than 20% Green indicator constant: Charging complete. Battery level higher than 98% or full

Do not tamper with the binoculars with brute force to avoid damage! Improper pupil distance may result in double vision or eyestrain. An accurate pupil distance helps you see a clearer image and relieves eyestrain.
07

Power Power on: Press and hold for 3 seconds Power off: Press and hold for 3 seconds Force restart: Press and hold for 10 seconds Press to enter Sleep Mode when powered on Press to wake up when in Sleep Mode
Status Indicator Face Cushion
08

Volume
RGB Perspective Camera Do not block the camera when using the product
A: IR Emitters B: Depth Camera
Do not block the camera when using the product

Top Strap Removable
Strap Dial Tracking Camera
Do not block the camera when using the product USB-C Compatible Port Left/Right Speaker

Proximity Sensor Wear the headset, and the system will wake up automatically
Take off the headset, and the system will enter Sleep Mode automatically
VST Indicator
When the VST camera is turned on, the white indicator will stay constant
When images are being saved, the white
indicator will flash

Note: The lanyard can be attached to the controller as shown in the image.

Controller Status Indicator
Off: Connected or powered off Blue indicator constant: Firmware upgrading Blue indicator flashing: Connecting Red and blue indicator flashing alternately: Waiting for pairingprogress Red indicator flashing: Unable to power on due to low battery level
09

Menu Button Home Button
Power on: Press Power off: Press and hold for 6 seconds Exit: Press Screen recentering: Press and hold for 1 second while powered on

Grip Button
Battery Case Opening: Toggle the button to pop out
the battery case
Installation: Press until it fits into place Status Indicator

Joystick Capture Button
Screenshot: Press Recording: Press and hold
Trigger Button

Operating Instructions

Head Control Mode
When the controllers are not connected,you can interact with the home screen by
moving your head to direct the crosshairs over your intended selection and clicking the Volume Up/Down button on the VR Headset.

Switching the pointer of the master controller
In the home screen, short press the Trigger of the corresponding Controller to switch the pointer of the master Controller.

Recentering the screen

Wear the headset and look straight ahead. Press and hold the “Home” button of the controller (or the “Volume Down” button of the headset in Headset mode) for

at least 1 second to recenter the screen and position the menu to your front.

Disconnecting the controller
Press and hold the “Home” button until the controller status indicator turns red
and the controller vibrates. The controller will now be disconnected from the head-
set and powered off. Controllers do not need to be powered off manually, as they will be automatically powered off to save power in the following scenarios:
· When the headset enters Deep Sleep Mode (after it is taken off for a certain period of time) · When the controllers are disconnected in the headset’s “Controller Management” screen
· When the headset is powered off

Adding a new controller
If you need to add a new controller (the headset can connect up to two controllers, a left one and a right one) or disconnect a controller and re-connect it, go to”Settings” “Controller”, click on “Pair” and press and hold the “Home” button and the “Trigger” button of the controller simultaneously until the controller status

indicator flashes red and blue alternately. Then follow the instructions on the headset screen.
Entering and exiting Sleep Mode Method 1: The system will enter Sleep Mode automatically after you take off the headset for a certain period of time. It will automatically wake up when you wear the headset. Method 2: Press the “Power” button of the headset to enter or exit Sleep Mode.
Hardware reset Resetting the headset If the headset is unresponsive or the image gets stuck when you press the “Power” button, press and hold the “Power” button for 10 seconds or longer to restart the headset. If the visual in the VR Headset freezes, or the VR Headset does not respond after short press the Power button, you can press the Power button of the VR Headset for more than 10 seconds to reboot the VR Headset.
Resetting the controller If the controller is unresponsive when you press the “Home” button or any other buttons, or if the virtual controller on the headset screen gets stuck, remove the batteries to restart the controller.
Vision correction This device does not support vision correction. The headset can be worn with most standard glasses that have a frame width of less than 150mm.

Installing glasses spacer
If you have glasses collision with headset lens or pressure on the bridge of nose, please follow the picture to install Glasses Spacer to increase the space. You can install or not according to your situation.

Remove the face cushion.
Install the Glasses Spacer on the Headset.

Install the Face Cushion on the Glasses Spacer.

Replacing the face cushion
The face cushion can get flaccid and discolored when cleaned multiple times or used for a long time. You can have it replaced with a new one if necessary.

Replacing the top strap

Remove the face cushion
Hold the metal buckle of the head strap and press it down until it can
be taken out, as shown in the image below

Fit the face cushion back

* Note: Disassemble the Glasses Spacer 11

EN 12

The essential tool for PICO all-in-one VR, helping you manage your headset better

·
· 2 × 2
· 12 13
JP ·
· 30
·
· [ ] 13

[ ][ ] · TÜV SÜD 3 [ ][ ][ ][ ] /
*
*

6DoF6 VR

1. 2 × 2
2. VR 3. VR
JP

2m
2m 14

1.5V 3

· ·

[ ][ ] JP
64 mm

98% 20% 98%
98% 20% 98%

3 3 10
18

RGB
A:
B:

USB-C /

VST VST

6 1

VR /

1 JP
· · [ ] ·
1 2 [ ][ ] [ ] 20

1 2
10

150mm

*
21

JP 22

PICO VR PICO VR

· .

· . .. . ( 2m x 2m) , .

· 13 . , , , 14 .

· .

· . 30 . . .

· ( , , ) . .

· ” ” . , . “” “” .

. · TÜV SÜD( ) ” ” .
3 . . “” “” “” ” ” .
* , . , . .
* , . .

VR 6
( / , / , / , , , ). , . .
1. 2 × 2 . , ( : ) / .
2. VR . 3. VR .

2m
2m
: ” ” . . 24

: 1.5V AA .

: ( ). : “” ( ).

“” 3 .

· . . · .

: . .
26

” ” “” “” . “+” “-” .
KR 64 mm

: : : :
: . 98% . : . 20% . : . 98% .
: . 98% . : . 20% . : . 98% .

! . .
27

: 3 : 3 : 10

RGB .
A: B: .

. USB-C /

. . VST
VST . .

: .

KR
: : : : :
29

: : 6 : : 1

: . : .

: :

VR ” / ” .
“” .
. “” ( ” ” ) 1 .
“” KR . . . · ( ) · ” ” ·
( 2 ) , “” “” “” “” “” . .
1: .
30

. 2: “” .
“” , “” 10 .
“” , .
. 150mm .

, . .

. .

.
.

* : .
31

KR 32

PICO VR

·
· ( 2 x 2 )
· 12 13
·
TH · 30
· ( )
· ( ) ” ” ” ” “”
33

· ” ” TÜV SÜD () ” ” ” “”” ” ” ” ”
*
*

VR 6
( / / / ) VR
1. 2 × 2 ( ) /
2. VR 3. VR

2m
2m : ” ” 34

: 1.5V AA

: ( )
: “” ( )

“/” 3

TH 35

· ·

TH
: 36

” ” “” “+” “-”
TH 64 mm

: : : : : 98% : 20% : 98% : 98% : 20% : 98%

!
37

TH
/ : 3 : 3 : 10
38

RGB
A: IR B:

USB-C
/

VST
VST

TH
: : : : :
39

: : 6 : : 1

Grip
: :

: :

“/” VR

“”

“” ( “” ) 1

“”

: · ()

· “”

( ) “” “” “” “” “”

1:
2: “/”
“/” “/” 10
“”
150 .

* : 41

TH 42

PICO all-in-one VR

Documents / Resources

PICO PICO 4 Ultra VR MR Headset [pdf] User Guide
PICO 4 Ultra VR MR Headset, PICO 4, Ultra VR MR Headset, VR MR Headset, Headset

References

User Manual

PICO 4 Ultra VR MR Headset

Specifications:

Product Usage Instructions:

Setting Up the Environment: