PHILIPS UID8470-10 Interact Ready Switches
UID8470
Zigbee Green Power switch
- No wiring and power connections required so easy to install.
- Low mechanical force required to operate the device (typically less than 8 Newton).
- Indoor distance that can be covered is typically 10 m (33 ft) for line-of-sight installations. When there are walls this is reduced depending on the type and thickness of the walls.
UID8470
Features and benefits
- Provides switch and dim functionality.
- Wireless communication based on the ZigBee Pro standard (IEEE 802.15.4, WPAN). This switch is a self-powered switch that operates using the kinetic energy generated through its button press action and electrical power supply is not required.
- When a button is pressed, or released, a message is sent including a unique 32-bit identifier that prevents interference with other devices.
- Briefly pressing the upper or lower part of the device either switches the lights ON or OFF.
- A press and hold action engages the dim-up or dim-down function.
- The device is Interact-ready and can be easily linked to a wireless standalone or connected lighting system.
- The devices are easy to install and use. Additional information can be found in the appropriate installation instructions.
Dimensional drawing
Specifications
Communication
| Wireless | Zigbee PRO Green Power IEEE 802.15.4 WPAN |
| Data rate | 250 kbps |
| Carrier frequency | 2.4 GHz |
Transmission distances (typical values)*
Indoor (plasterboard) 10 m (33 ft); max. 3 walls
Indoor reinforced concrete 7 m (23 ft); max 1 wall/ceiling
Physical
- Dimensions (H x W x D) 81 x 81 x 14 mm (3.19 x 3.19 x 0.55 in)
- Weight 0.058 kg (2.05 oz)
- Housing Polycarbonate Color
- White (similar to RAL9000)
- Lifetime > 50 000 actuations
Environment
* Distance is largely influenced by the wall/ceiling material and the angle that the transmitted signal is intersecting with. Note:fire-safety walls, elevator shafts and so on are considered asshielding.
Compliances and approvals
- Protection rating IP20
- Electromagnetic compatibility (EMC)
- EN 61000-6-2:2005 EN 61000-6-4:2007+A1:2011
- Quality standard ISO9001
- Environmental standard
- ISO14001, CE2522
- Restriction of Hazardous Substances (RoHS) 2011/65/EU
- Annex 2015/863/EU Wireless
- Radio Equipment Directive
- RED 2014/53/EU
- Electronic compatibility and radio spectrum matters (ERM)
- EN 301489-1:V2.2.0 EN 301489-17:V3.2.0
- Wideband transmission systems
- ETSI EN 300 328: V1.8.1
Packing data
| Type | Dimensions | Qty | Material | Weight | |
| net | gross | ||||
| Single pack | 205 x 95 x 95 mm
(80.7 x 37.4 x 37.4 in) |
10 | Cardboard | 0.58 kg
(1.28 lb) |
0.74 kg
(1.63 lb) |
Ordering data
| Type | MOQ | Ordering number | EAN1 | EAN2 | EOC |
| UID8470/10 ZGP Switch Dim 2B | 10 | 9137 010 55703 | 8719514 273771 | 8719514 273795 | 273771 00 |
© 2020-2024 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
FAQ
- Q: Can I use multiple Interact Ready switches with one lighting system?
A: Yes, you can pair multiple switches to control different zones or aspects of your lighting system. - Q: How do I reset the Interact Ready Switch Dim 2B?
A: Refer to the user manual for specific instructions on resetting the switch to factory settings.
Documents / Resources
 |
PHILIPS UID8470-10 Interact Ready Switches [pdf] Owner's Manual UID8470-10, ZGP Switch Dim 2B, UID8470-10 Interact Ready Switches, UID8470-10, Interact Ready Switches, Ready Switches, Switches |