10-Key 8 Scene RF Remote Controller
Model No.: R8S
8 scene/10-key/Wireless remote 30m distance/CR2032 battery/Magnet stuck fix
Features
- 8 scene RF 2.4G remote.
- Apply to a single color, dual color, RGB, RGBW, or RGB+CCT RF LED controller.
- Each remote can match one or more receivers.
- RC 2032 attery powered.
- Operate with LED indicator light.
- Magnet on the back which can be easily stuck on back holder or any metal surfaces.
Technical Parameters
| Input and Output | |
| Output signal | RF (2.4GHz) |
| Working voltage | 3VDC (CR2032) |
| Working current | ＜5mA |
| Standby current | ＜2μA |
| Standby time | 2 years |
| Remote distance | 30m(Barrier-free space) |
| Environment | |
| Operation temperature | Ta: -30 ºC ~ +55 ºC |
| IP rating | IP20 |
| Safety and EMC | |
| EMC standard (EMC) | ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 |
| Safety standard(LVD) | EN 62368-1:2020+A11:2020 |
| Radio Equipment(RED) | ETSI EN 300 328 V2.2.2 |
| Certification | CE,EMC,LVD,RED |
| Warranty | |
| Warranty | 5 years |
| Weight | |
| Gross weight | 0.040kg |
| Net weight | 0.064kg |
Mechanical Structures and Installations
To fix the remote, three options are offered for selection:
Option 1: stuck the remote on any metal surfaces directly.
Option 2: fix the remote’ back holder on the wall with two screws.
Option 3: adhere the remote’ back holder to the wall with a paster.
Match Remote Control (two-match ways)
End-user can choose the suitable match/delete ways. Two options are offered for selection:
| Use the controller’s Match key Match: Short press the match key, and immediately press the ON key on the remote. The LED indicator fast flash a few times means the match is successful. Delete: Press and hold the match key for 5s to delete all matches, The LED indicator fast flash a few times means all matched remotes were deleted. |
Use Power Restart Match: Switch off the power, then switch on the power, and repeat again. Immediately short press the ON key 3 times on the remote. The light blinks 3 times means the match is successful. Delete: Switch off the power, then switch on the power, and repeat again. Immediately short press the ON key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. |
Key function
ON:
Turn on the last scene light.
OFF:
Turn off the last scene light.
Scene 1-8:
Recall the scene saved in the RF controller.
Note:
The remote only has a scene recall function default.
If you want to use the scene save function, please long press ON + S8 key 2s to enable the scene save function, then long-press Scene 1-8 key 2s to save the current color into this scene number. the LED indicator will light up longer when save OK.
When all 8 scenes save OK, please long press OFF + S8 key 2s to disable the scene save function.
Safety information
- Read all instructions carefully before you begin this installation.
- When installing the battery, pay attention to the battery’s positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. - If no response from the receiver, please re-match the remote.
- Gently handle the remote, beware of falling.
- For indoor and dry location use only.
User Manual Ver 1.0.0
R8S 10-Key 8 Scene RF Remote Controller
Documents / Resources
 |
Philio R8S 10-Key 8 Scene RF Remote Controller [pdf] User Manual R8S, 10-Key 8 Scene RF Remote Controller |
