PAROS, PAROS SUB Passive Full Range/Subwoofer Array Speaker User Manual

Pull out the latch and turn the connector upwards.
Fix the connector of the first sound with the latch, then pull out the latch of the second sound and connect it to the first sound.

Speaker Rear Connection Method

To connect the speakers at the rear:

Pull out the plug.
Flip the connector upward.

Insert the second stereo into the second speaker to complete the connection.

Hanger and Full-Range Box Connection Method

To connect the full-range box hanger to the full-range box:

Install the full-range box hanger on the full-range box.

Frequently Asked Questions

Troubleshooting and Diagnostics

If you encounter issues like no sound from speakers or playing with noise, follow these steps:

Please check if the power cord connection is plugged in tightly and turned right to the ON position.
Ensure all connecting wires of the cable are properly connected and secure.

Verify that the DSP and LEVEL setting gears are in their normal positions.
Confirm that the source equipment is functional and capable of broadcasting required signals.

If the level setting is too low, adjust the output level setting of the source device or raise the output level with the LEVEL controller.
Check if the audio input is normal and examine for bent, shorted, or broken cables.

USING THE UNIT SAFELY

INSTRUCTIONS FOR THE PREVENTION OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

ALWAYS OBSERVE THE FOLLOWING

IMPORTANT NOTES
Power Supply: Use of Batteries

Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter (such as a refrigerator, washing machine,microwave oven, or air conditioner), or that contains a motor. Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect a power supply noise filter between this unit and the electrical outlet.

The AC adaptor will begin to generate heat after long hours of consecutive use. This is normal, and is not a cause for concern.
When installing or replacing batteries, always turn off the power on this unit and disconnect any other devices you may have connected. This way, you can prevent malfunction and /or damage to speakers or other devices.

Use only suitable rechargeable batteries of the same size and type. Make sure the polarity is correct. Or it may cause this unit to malfunction.
Please charge the battery as soon as you can when in low energy. The battery’s storage capacity goes down if not using it for a long time.

Note: Please charge the battery once a month regularly if not using it for long period.

Placement

Using the unit near power amplifier (or other equipment containing large power transformers) may induce hum.
To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interterence.
This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers.
Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off.
Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes.
Also, do not allow lighting devices that normally are used while their light source is very close to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
When moved from one location to another where the temperature and /or humidity is very different, water droplets (condensation) may form inside the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.
Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time.
Such objects can discolor or otherwise harmfully affect the finish.
Do not paste stickers, decals, or the like to this instrument. Peeling such matter off the instrument may damage the exterior finish.

Maintenance

For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth.
Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

Additional Precautions

Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its Jacks and connectors. Rough handling can lead to malfunctions.
When connecting/disconnecting all cables, grasp the connector itself-never pull on the cable. This way you will avoid causing shorts, or damage to the cable’s internal elements.

To avoid disturbing your neighbors, try to keep the unit’s volume at reasonable levels (especially when it is late at night or near specific places like schools or hospitals).
When you need to transport the unit, package it in the box (including padding) that it came in, if possible.
Otherwise, you will need to use equivalent packaging materials.
Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.

Product Component Name

PAROS products in the box

PAROS SUB products in the box

Spare parts

Product Portfolio Approach

portfolio approach

Floor-standing + lifting
Suitable for 300-500 viewers

Recommended configuration
Full-range speaker and bass ratio 2:1, the best ratio of 3:2

Operating modes and connections

Angle adjustment between speakers
The angle of the satellite box can be adjusted by 0°0.5°1°2°3°4°5°6°7°8° through different holes.

Connection method between speakers

Pull out the latch and turn the connector upwards
Fix the connector of the first sound with the latch, pull out the latch of the second sound and connect the first sound
1. Fix the connector of the first sound with the latch, pull out the latch of the second sound and connect the first sound

Speaker Rear Connection Method

Pull out the plug
Flip the connector upward
Put in the second stereo will be plugged into the second speaker to complete the on-line

Hanger and full-range box connection method

Install the full-range box hanger on the full-range box

Control Panel illustration

PAROS Panel Function Introduction

For two parallel four-pole SPEAKON female chassis,you can connect any one of them to a LINE signal source (such as mixing consoles, effects, etc.), and at the same time, the signal can be connected from the other female chassis to the signal input connector of the next PAROS.

Product Specification

Model number	PAROS	PAROS SUB
Type	Passive Full-Range Array Speaker	Passive Subwoofer Array Speaker
Frequency range -10dB
Element impedance
Directivity	90°Horizontal X 8°	/
Sensitivity
Frequency division point		/
System power
Signal Input Interface
Signal Output Interface
speaker unit	Bass: 12“ Bass2 Midrange: 8” Midrange2 Treble:3” driver*2	Bass:18 “ Bass*2
lifting	Lifting bracket, 0, 0.5, 1, 2, 3, 4, 5, 6, 7, 8° adjustable	Lifting bracket
cabinet	Full Birch PLY	Full Birch PLY
mesh cover	1.5mm steel mesh	1.5mm steel mesh
Product Color	Black	Black
Product size (height, width and depth)
Product weight (net)
Package Size
Gross Weight

Troubleshooting and diagnostics

No sound from speakers	A. Please check if the power cord connection is plugged in tightly and turn right to ON position.
	B. Please check that all connecting wires of the cable are properly connected and that the connection is secure.
	C. Check that the DSP and LEVEL setting gears are in the positions corresponding to the normal gears.
	D. Ensure that the source equipment is functional and capable of broadcasting the required signals.
	E. Check if the level setting is too low, adjust the output level setting of the source device, or raise the output level with the LEVEL controller.
Playing with noise	A. Check if the audio input is normal.
	B. Check for bent, shorted or broken cables.
	C. Check that the signal connecting wires are in good contact.
	D. If the signal indicator lights up red, it means the output volume is too high, adjust the output level setting of the audio device,or use the LEVEL controller to adjust the output level.
Different sound for each speaker (if more than one speaker is used)	Set the DSP switch and LEVEL switch to the same position for each speaker.
Sound breaks	Please wait until the amplifier has cooled down. If the unit does not reset itself automatically, turn the power off and then back on again.

Documents / Resources

PAROS PAROS, PAROS SUB Passive Full Range/Subwoofer Array Speaker [pdf] User Manual
PAROS PAROS SUB Passive Full Range Subwoofer Array Speaker, PAROS PAROS SUB, Passive Full Range Subwoofer Array Speaker, Full Range Subwoofer Array Speaker, Subwoofer Array Speaker, Array Speaker, Speaker

References

User Manual

PAROS, PAROS SUB Passive Full Range/Subwoofer Array Speaker

Product Usage Instructions