D035 REMOTE CONTROL | TAG
The remote control is designed to control and monitor a state of a security system at a distance of a Bluetooth connection.
ATTENTION! Enable the “Use D-030 as a radio tag” option to use the remote control as an owner authorization device.
- OLED-display
- Three control buttons
- Built-in sound indicator (16 melodies for sound notifications)
- Built-in vibration indicator
- Built-in LED indicator “ALARM/SEND”
- 2.4 GHz radio interface (Bluetooth 5.0 protocol)
- Built-in battery
- Built-in micro-USB port
OPERATING RANGE: from -10º C to +40º C DEGREE OF PROTECTION: IP40
COMPATIBILITY
Pandora ELITE v.2, Smart Pro v.3, Camper Mini, Camper Pro v.2, Mini v.3
TURNING ON/OFF THE REMOTE CONTROL
Press and hold
the button for 3 seconds to turn ON/OFF the remote control
REMOTE CONTROLLED SIGNALS MEANING
| Red indicator «ALARM» | Green indicator «SEND» |
| Flashes frequently if there are any notifications | Flashes if there is a connection with the base unit |
| Flashes occasionally when there is no connection | Goes dark when there is no connection with the base unit |
CHARGING THE REMOTE CONTROL
There is a battery charge level icon
on the display of the remote control. It is recommended to charge the remote control if only the last segment of the icon is shown
. Charge the built-in battery with a standard micro-USB cable.
FIRMWARE UPDATE
- Download the mobile application Pandora BT (Android/iOS) or Pandora Specialist (Android) to the smartphone or a tablet equipped with Bluetooth 4.0 or higher.
- Press and hold the button, connect a USB cable to the remote control, release the button after connection.
- Open the mobile application, go to the “Search device“ menu, select a found device and choose one of the update options: FILE MANAGER (only for Andriod devices) or INTERNET.
 |
connected |
 |
security mode disarmed/armed |
 |
current time |
 |
battery charge level |
 |
engine temperature |
 |
interior temperature |
 |
outside temperature |
 |
the voltage of the car battery |
 |
fuel level |
 |
shock sensor (Warning level) |
 |
shock sensor (Alarm level) |
 |
additional sensor (Warning level) |
 |
additional sensor (Alarm level) /Status of the original alarm system |
 |
security zone Tilt sensor |
 |
security zone Motion sensor |
 |
security zone Ignition ON |
 |
security zone Doors |
 |
security zone Hood |
 |
security zone Trunk |
 |
security zone Low voltage |
 |
security zone Brake pedal |
 |
Engine running icon |
QUICK ACCESS FUNCTIONS OF THE REMOTE CONTROL
|
System disarmed |
System armed (no alarm events) | ||
| Ignition ON | Ignition OFF | ||
 (briefly) |
Lock doors without arming | Arming with sound confirmation | Search mode – Flashing hazard lights with sound signals for 5 sec |
| (1 sec) |
Arming without sound confirmation | Search mode – Flashing hazard lights without sound signals for 5 sec | |
| (2 sec) |
Hold-On ignition mode ON | ||
(3 sec) |
Program neutral mode ON | Remote engine start | |
 (briefly) |
Unlock doors | Unlock doors | Disarming with sound confirmation |
| (1 sec) |
Disarming without sound confirmation | ||
(2 sec) |
Hold-On ignition mode OFF | Switch OFF the ignition during remote/automatic engine start, turbo timer | |
| (3 sec) |
Service mode ON/OFF | ||
| (briefly) |
Switch on the LCD display | ||
| (1 sec) |
Unlock trunk | ||
| (2 sec) |
Switch ON an engine heater*
Switch ON/OFF a time channel |
||
| (3 sec) |
Switch ON/OFF the remote control | ||
| +
(briefly) |
PANIC mode | ||
|
(briefly) |
Arming when the ignition is ON with sound confirmation | Arming in 30 sec with sound confirmation | |
| + (1 sec) |
Arming when the ignition is ON without sound confirmation | Arming in 30 sec without sound confirmation | |
* To control an engine heater, it is required to make setting in Time channels:
“Select channel” – for analog control, “Action 1” – “Switch on engine preheater”
Documents / Resources
 |
Pandora D035 Remote Control [pdf] User Manual D035, Remote Control, Tag |
