Panasonic CONNECT PT-VMZ50 Compact and Cost Efficient LCD Laser Portable Projector Owner's Manual

Setup and Installation:
- Ensure the projector is placed on a stable surface and at an appropriate distance from the screen or projection surface. Connect the necessary cables for power and input sources.

Power On/Off:
- To power on the projector, press the power button located on the control panel or the remote. To power off, use the appropriate power-off function to avoid damage to the device.

Adjusting Image:
- Use the zoom feature to adjust the size of the projected image according to your needs. The wide horizontal and vertical lens shift options allow for flexible positioning of the image on the screen.

Maintenance:
- Regularly clean the projector lens and vents to ensure optimal performance. Check the laser light source for any signs of deterioration and follow manufacturer guidelines for maintenance.

FAQs

Q: Is it possible to connect external devices to the projector?
- A: Yes, the projector supports various input sources such as HDMI, VGA, and USB for connecting external devices.

Q: How can I adjust the focus of the projected image?
- A: Use the focus adjustment ring on the projector lens to achieve a sharp and clear image.

View Fullscreen

5,000lm compact and cost-efficient LCD laser portable projector.
PT-VMZ50
Designed for Long-Lasting brightness and easy installation for education and corporate environments

Key Features
Laser LCD, 5,000 lumens, WUXGA.
Compact and lightweight body bringing high brightness dynamic image
Long lasting laser light source provide consistent brightness
1.6x zoom and wide horizontal and vertical lens shift for flexible installation
Long lasting laser light source and low-maintenance design provide high brightness and superb image quality

P T- V M Z 5 0
https://ap.connect.panasonic.com/id/en/products/projectors/pt-vmz50

To remove the battery

Remote Control Battery
1. Press the guide and lift the cover.
(ii)
(i)
2. Remove the batteries

rTrademarks
f SOLID SHINE is a trademark of Panasonic Corporation.
f The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
f Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.
f Crestron Connected, the Crestron Connected logo, Crestron Fusion, Crestron RoomView, and RoomView are trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
f HDBaseTTM is a trademark of HDBaseT Alliance.
f Windows, Internet Explorer and Microsoft Edge are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.
f Mac, OS X, macOS, iPad, iPhone, iPod touch and Safari are trademarks of Apple Inc., registered in the United States and other countries.
f IOS is a trademark and registered trademark of Cisco in the United States and other countries and is used under license.
f Android and Google Chrome are trademarks of Google LLC.
f Adobe, Acrobat, Flash Player, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
f Some of the fonts used in the on-screen menu are Ricoh bitmap fonts, which are manufactured and sold by Ricoh Company, Ltd.
f All other names, company names, and product names mentioned in this manual are trademarks or registered trademarks of their respective owners.
Please note that the ® and TM symbols are not specified in this manual. rSoftware information regarding this product

This product incorporates the following software:
(1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software licensed under the GNU General Public License, Version 2.0 (GPL V2.0), (4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL V2.1), and/or (5) open source software other than the software licensed under the GPL V2.0 and/or LGPL V2.1. The software categorized as (3) – (5) are distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Please refer to the detailed terms and conditions thereof shown in the “Operating Instructions – Basic Guide” supplied with the product.
At least three (3) years from delivery of this product, Panasonic will give to any third party who contacts us at the contact information provided below, for a charge no more than our cost of physically performing source code
distribution, a complete machine-readable copy of the corresponding source code covered under GPL V2.0, LGPL
V2.1 or the other licenses with the obligation to do so, as well as the respective copyright notice thereof.
Contact Information: oss-cd-request@gg.jp.panasonic.com
Presenter Light uses the following software programs.
A portion of this software is based in part on the work of the Independent JPEG Group.
rIllustrations in these operating instructions
f Illustrations of the projector, menu screen (OSD), and other parts may vary from the actual product.
f Illustrations displayed on the computer screen may differ depending on the computer type and its operating system.
f Illustrations of the projector with the power cord attached are only examples. The shape of the supplied power cords varies depending on the country where you purchased the product.
rPage references
f Reference pages in this manual are indicated as : (Æ page 00).
rTerm
f In this manual, the “Wireless remote control unit” accessory is referred to as the “Remote control”.

Features of the Projector

Compact design and light weight
▶With a compact design and light weight of 7.2 kg, while achieving a brightness of 6 000 lm*1.
*1 5 000 lm for PT-VMZ50 and PT-VMW50, 4 500 lm for PT-VMZ40.

High reliability
▶ The SOLID SHINE laser light source allows
long-term operation of 20 000 hours*1. *1 This is an estimated usage time until the brightness is approximately halved, under conditions with a dust level of 0.15 mg/m3
, [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [LIGHT POWER] set to [NORMAL] and [PICTURE] menu → [DYNAMIC CONTRAST] set to [2].

Flexible setup
▶ With vertical/horizontal lens shift function and a lens of 1.6x zoom ratio, flexible installation is possible even in limited spaces.

Excellent extensibility
▶ 4K signal*1 input is supported to embrace a future system update.
▶ Easy wireless projection is possible by using the optional wireless module.
*1 Supports signals up to 4K/30p. A signal with different resolution is converted to the number of display dots. PT-VMZ60/PT-VMZ50/PT-VMZ40: 1 920 x 1200 dots PT-VMW60/PT-VMW50: 1 280 x 800 dots

Quick Steps

For details, refer to the corresponding pages.
1. Set up your projector. (x page 32)
2. Connect with external devices. (x page 36)
3. Connect the power cord. (x page 42)
4. Power on. (x page 44)
5. Make initial settings. (x page 44)
f Take this step when you power on for the first time after purchasing the projector.
6. Select the input signal. (x page 48)
7. Adjust the image. (x page 50)

Preparation

This chapter describes things you need to know or check before using the projector.

Intended use of the product
The product is intended to project still/moving image signals from video equipment and computers onto a screen.

Cautions when transporting
f When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. Doing
so may damage the internal parts and result in malfunctions.
f Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
f Do not move or transport the projector with the wireless module (Model No.: AJ-WM50) of the optional
accessories attached. Doing so may damage the wireless module.

Cautions when installing

rDo not set up the projector outdoors.
The projector is designed for indoor use only.
rDo not use under the following conditions.
f Places where vibration and impacts occur such as in a car or vehicle: Doing so may damage the internal parts and result in malfunctions.
f Location close to sea or where corrosive gas may occur: the projector may fall due to corrosion. Also, failure to do so may shorten the life of the components and result in malfunction.
f Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases due to the heated air from the air exhaust port or the hot or cooled air. Make sure that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward the front of the projector.
f Places with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of the light source, or result in deformation of the outer case due to heat, which may cause malfunction. Make sure to observe the operating temperature range of the projector.
f Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector..

Ask a qualified technician or your dealer for the installation work such as installing to a ceiling, etc.
To ensure projector performance and safety, ask a qualified technician or your dealer when installing to a ceiling or in a high place.
rAsk a qualified technician or your dealer to install the cable wiring for DIGITAL LINK connection.
(Not available for PT-VMZ40)
Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate installation.

The projector may not work properly due to strong radio wave from the broadcast station or the radio. (Not available for PT-VMZ40) If there is any facility or equipment which outputs strong radio waves near the installation location, install the projector at a location sufficiently far from the source of the radio waves. Or, wrap the LAN cable connected to the terminal using a piece of metal foil or a metal pipe which is grounded at both ends.

rFocus adjustment
The projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on the power. It is recommended that the images are projected continuously for at least 30 minutes before the focus is adjusted.

rDo not install the projector at elevations of 2 700 m (8 858′) or higher above sea level.
rDo not use the projector in a location that the ambient temperature exceeds 45 °C (113 °F).
Using the projector in a location that the altitude is too high or the ambient temperature is too high may shorten the life of the components or result in malfunctions.
When the optional wireless module (Model No.: AJ-WM50) is attached, do not use the projector in a location that the ambient temperature exceeds 40 °C (104 °F).
rProjection in all 360° direction is possible.

Cautions when setting the projectors
f Use the adjustable feet only for the floor standing installation and for adjusting the angle. Using them for other purposes may damage the projector.
f When installing the projector with a method other than the floor installation using the adjustable feet or the ceiling installation using the ceiling mount bracket, use the four screw holes for ceiling mount (as shown in the figure) to fix the projector.
In such case, make sure that there is no clearance between the screw holes for ceiling mount on the projector bottom and the setting surface by inserting spacers (metallic) between them.
f Use a torque screwdriver or Allen torque wrench to tighten the fixing screws to their specified tightening torques. Do not use electric screwdrivers or impact screwdrivers.
(Screw diameter: M4, tapping depth inside the projector: 8 mm (5/16″), torque: 1.25 ± 0.2 N·m)

f Do not stack the projectors.
f Do not use the projector supported by its top.
f Do not block the ventilation ports (intake and exhaust) of the projector.
f Avoid heating and cooling air from the air conditioning system directly blow to the ventilation ports (intake and exhaust) of the projector.

Getting Started

Setting up
Installation mode
There are four ways to set up the projector. Set the [PROJECTOR SETUP] menu → [PROJECTION METHOD] (x page 84) depending on the installation mode.

Note
f The projector has a built-in angle sensor. The attitude of the projector is automatically detected by setting the [PROJECTOR SETUP] menu → [PROJECTION METHOD] to [AUTO]. For rear projection, set the [PROJECTION METHOD] to [REAR/DESK] or [REAR/CEILING].

rAngle sensor
The range of installation posture detected by the projector’s built-in angle sensor is as follows.

Parts for ceiling mount (optional)
This requires an optional ceiling mount bracket. Be sure to use the Projector Mount Bracket together with the ceiling mount bracket for high ceilings or low ceilings.
Model No.: ET-PKL100H (for high ceilings), ET-PKL100S (for low ceilings), ET-PKV400B (Projector Mount Bracket)
f Use only the ceiling mount brackets specified for this projector.
f Refer to the Installation Instructions for the ceiling mount bracket when you install the bracket and the projector.

Attention
f To ensure projector performance and security, installation of the ceiling mount bracket must be carried out by your dealer or a qualified technician.

Screen size and throw distance
Refer to the screen size and projection distances to install the projector. Image size and image position can be adjusted in accordance with the screen size and screen position.
f Following illustration is prepared on the assumption that the projected image size and position have been aligned to fit full in the screen.

Basic Operations

Switching on/off the projector
Connecting the power cord
Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily.
For details of power cord handling, refer to “Read this first!”. (x page 4)
Attaching the power cord

1) Check the shapes of the terminal on the back of the projector body and the power cord connector and insert the plug completely in the correct direction. 2) Fix the power cord connector to terminal by tightening the fixing screws on both sides of the power cord connector.

Attention f If the power cord connector is not fixed to the terminal with the fixing screws or the fixing screws are not tightened securely, poor contact may occur between the power cord connector and the terminal. Consult your dealer for repairing the power cord.

Removing the power cord

1) Confirm that the projector is in standby mode, and remove the power plug from the outlet. 2) Loose the fixing screws on both sides of the connector and remove the power plug from the terminal.

Documents / Resources

Panasonic CONNECT PT-VMZ50 Compact and Cost Efficient LCD Laser Portable Projector [pdf] Owner's Manual
PT-VMZ50, PT-VMZ50 Compact and Cost Efficient LCD Laser Portable Projector, Compact and Cost Efficient LCD Laser Portable Projector, Efficient LCD Laser Portable Projector, LCD Laser Portable Projector, Laser Portable Projector, Portable Projector

References

User Manual

Panasonic CONNECT PT-VMZ50 Compact and Cost Efficient LCD Laser Portable Projector

Specifications

Product Usage Instructions