Pace TECHNOLOGY TruPin Pace Fleet Management
Dimensions
Front and Side View
Back View
Hardware Specifications
| Features | Description |
| OS | FreeRTOS — real-time embedded OS |
| Processor | ESP32-S2 embedded, Xtensa® single-core 32-bit LX7 microprocessor, up to 240 MHz |
| Memory | 128 KB ROM + 320 KB SRAM + 16 KB SRAM in RTC + 4 MB Flash Internal |
| LTE Cellular Modem | Telit SMT CELL MODEM – CAT-M1 ME310G1-WW
LTE UE Cat M1, 3G and 2G global fallback frequency support – 15x18mm Requires SIM holder |
| GPS | Locosys MC-1010-V2b |
| Wi-Fi | Espressif ESP32 S2 WROOM module |
|
Antennas |
GNSS: Taoglas One Stage GPS-GLONASS-GALILEO-BeiDou Embedded Active Patch Antenna Module with Front-End SAW Filter AGVB.25A.07.0060A; patch antenna (uFL connected);
Wi-Fi – PCB antennas on the main board; LTE – Internal ceramic antenna SR4L034-L |
| Battery | 1S configuration; Lithium Polymer chemistry. – default configuration 1500mAh cell. MIKROE-4473 |
| Vibration | DC Motor VC1030B028F |
| Sound | Piezo Buzzer CMT-1032-85-SMT-TR |
| LED | Low current Red/Green APBD3224LSURKZGKC |
| LCD | 102×64 pixels (EA DOGS102W-6) with white backlight (EA LED39X41-W) |
System Details
- Operating System
The board runs a customized version of an embedded OS featuring multitasking libraries, device drivers, and other components required to operate the hardware platform. - Application Processor
ESP32 S2 embedded, Xtensa® single core 32 bit LX7 microprocessor, up to 240 MHz - LTE Modem
Telit ME310G1 WW modem with internal antenna (Antenova SR4L034 L and SIM holder. - Wi-Fi
Espressif ESP32 S2 WROOM module - GNSS GPS
Integrated receiver Locosys MC 1010 V2b module with Taoglas AGVB.25A.07.0060A internal patch antenna. - Battery
The base configuration contains 1500mAh@3.7V Lithium Polymer (lipo) cells. - Vibration
The device contains vibration for feedback. - Display
LCD use SPI interface - Charging
2W Wired USB C - Sound
The device features a piezoelectric buzzer.
Connectors
- USB C 2.0
Environmental Conditions
- Operating Temps
- 4°F to 122°F
- Storage Temps
- 40°F to 185°F
- Test IP67
- Water
- 30 minutes submerged no deeper than 40 inches
- Dust
User Guide
Features
Turning On the Device
*Note that the TruPin device should be powered on 5 10 minutes prior to use for the device to acquire the satellite signal.
Marking Tee Position
From the Main menu, select “Courses.”
From the “ menu, you will be able to select your course
Once a course has been selected, you will be directed to the “ menu.
- Select Current Hole
From the “ menu, select the hole on which the tees will be marked. - Mark Tees Position
Once the holes have been cut, hold the device over the center of the hole and select the “Tees” option to mark the location. - Await Confirmation
After marking the tees, a confirmation will appear on the screen indicating a successful position mark.
Navigate back to the hole selection screen after completing each hole to select the next hole. Repeat this process until all holes are complete.
Marking Pin Position
To mark a pin position, repeat the same process for marking a tee position, but selecting the “ option instead.
From the Main menu, select “Courses.”
From the “ menu, you will be able to select your course
Once a course has been selected, you will be directed to the “ menu.
- Select Current Hole
From the “ menu, select the hole on which the pin will be marked. - Mark Pin Position
Once the holes have been cut, hold the device over the center of the hole and select the “Pin” option to mark the location. - Await Confirmation
After marking the pin, a confirmation will appear on the screen indicating a successful position mark.
Navigate back to the hole selection screen after completing each hole to select the next hole. Repeat this process until all holes are complete.
Turning Off Device
To turn off the TruPin device, navigate to the Main menu and scroll down to select “Power.” In the “Power” menu, select the “Sleep” option to turn off the device.
FCC Statement
Regulatory Compliance Information
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installatio n. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not oc cur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: 2BBDD TRUPIN
IC Requirement
This device contains licence-exempt transmitter(s) /receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Requirement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.The digital apparatus complies with Canadian CAN ICES 3 (B)/NMB 3(B).
For Transmitter: This device meets the exemption from the routin e evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure. users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.
Contact
- Textron
- Specialized Vehicles 1451
- Marvin Griffin Rd Augusta, GA 30906
- Phone: 800 241 5855
- www.ezgo.com
FAQ
- Q: How do I charge the device?
- A: The device can be charged using a 2W Wired USB-C connection.
- Q: What is the battery capacity?
- A: The device comes with a 1500mAh Lithium Polymer (LiPo) battery.
Documents / Resources
 |
Pace TECHNOLOGY TruPin Pace Fleet Management [pdf] User Manual 2BBDD-TRUPIN, 2BBDDTRUPIN, TruPin Pace Fleet Management, TruPin, Pace Fleet Management, Fleet Management, Management |