T019-04 TireView LIVE Sending Unit, Repeater and Harness and Repeater
“
Specifications
- Product: TPMS Sending Unit, Repeater and Harness
Installation - Application: Trailer
- Manufacturer: Clarience Technologies Company
- Model Number: T019-04
- Revision Date: 08-25
Product Information
The TPMS Sending Unit, Repeater, and Harness Installation kit is
designed for trailer applications. It includes components such as
TireView LIVE Sending Unit, Repeater, Wire Harnesses, Hardware Bag,
Cable Ties, and Decals.
Installation Instructions
Step 1: Mounting Location Identification
Identify a suitable mounting location for the sending unit and
repeater. Ensure the power source location is considered. It is
recommended to mount the gateway and repeater at least 4 feet from
each other to optimize performance.
Suspension Placement
Install the repeater to ensure proper operation of the system.
Avoid mounting components and wiring above the slider rail if the
trailer is equipped with a slider box to prevent damage during
suspension movement.
Sending Unit Placement
Recommended placement locations include suspension cross member,
lift gate housing, or battery box. Avoid mounting the gateway where
tires can throw debris onto the enclosure.
Step 2: Mounting the Sending Unit
Use the sending unit as a template to mark mounting hole
locations and drill with a 3/8 drill bit. Attach the sending unit
to the vehicle using supplied bolts, washers, and locknuts. Torque
the mounting bolts to 8-10 ft.-lbs.
Caution:
Utilize a strain relief cable tie with a drip loop configuration
when mounting the sending unit. Ensure the Weather Pack connector
faces downward for proper installation.
For Battery Backup Sending Unit:
Ensure the connector points down and create a drip loop with the
harness for correct installation.
Frequently Asked Questions (FAQ)
Q: What should I do if I encounter issues with the TPMS system
after installation?
A: If you encounter any issues with the TPMS system
post-installation, please refer to the troubleshooting section of
the user manual. Ensure all connections are secure and follow the
installation instructions carefully.
Q: Can I install the TPMS system on any type of trailer?
A: The TPMS system is designed for trailer applications. Ensure
compatibility with your specific trailer model before
installation.
“`
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
INSTALLATION MANUAL
TireView® LIVETM Sending unit, Harness and Repeater Installation
Trailer Applications
www.psitireinflation.com/resources#tpms-resources
© 2025 Pressure Systems International, LLC.
1
A Clarience Technologies Company.
V019 04 TVL Trailer Install Video
T019-04 Rev 08-25
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
About this Manual This manual supplies installation procedures for the TireView® LIVETM sending unit. Use the procedures in this manual to install the system on commercial vehicles. Before You Begin
CAUTION: DO NOT PERFORM UNAUTHORIZED MAINTENANCE OR REPAIR PROCEDURES, OR INSTALL NON-P.S.I.® COMPONENTS ON ANY P.S.I. ® SYSTEM. THIS CAN VOID THE WARRANTY. 1. Read and understand all instructions and procedures before service to components begins. 2. Read and observe all Warning and Caution alert messages in this publication. They provide information that can prevent personal injury, damage to components, or both. 3. Follow the P.S.I. installation, maintenance, service, and troubleshooting guidelines. 4. Use special tools, when required, to avoid personal injury and damage to components. 5. Use personal protective equipment (PPE), when required, to avoid personal injury. Safety glasses, safety toe shoes, and gloves recommended.
Hazard Alert Messages and Torque Symbols
WARNING: A Warning alerts the technician to an instruction or procedure that must be followed to avoid personal injury and damage to components.
CAUTION:
A Caution alerts the technician to an instruction or procedure that must be followed to avoid damage to components.
TORQUE REQUIRED: The torque symbol alerts the technician to tighten fasteners to a specified torque value.
Additional Information Visit the Resource section at www.psitireinflation.com to access and request additional information. Call P.S.I.® at 210.222.1926 (United States and Canada) or email info@psitireinflation.com or techsupport@psitireinflation.com.
Introduction
The P.S.I.® TireView® Tire Pressure Monitoring System (TPMS) is designed to monitor air pressure and temperature in the tire. It is only for added safety and not meant to replace regular tire maintenance and exercise of reasonable care when operating a motor vehicle. The system cannot prevent accidents nor will P.S.I.® be responsible for damage or injury due to (a) improper use,(b) failure to follow the product manufacturer’s instructions or to perform preventative maintenance, (c) unauthorized repair or modifications, (d) use of products beyond their useful life, or (e) external causes such as accidents, abuse, or other actions or events outside of P.S.I.® control.
© 2025 Pressure Systems International, LLC.
2
A Clarience Technologies Company.
T019-04 Rev 08-25
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
Introduction
This manual is intended to provide guidance when installing the TireView® LIVETM sending unit and repeater on a commercial truck, tractor, or similar vehicle. Your configuration may vary due to type of equipment. Consult your support team for guidance.
Sending Unit, Harness and Repeater Components
PART DESCRIPTION
EXAMPLE
TireView LIVE Sending Unit (Battery Backup optional)
TireView Repeater
Wire Harnesses
Hardware Bag Cable Ties
Decals
© 2025 Pressure Systems International, LLC.
3
A Clarience Technologies Company.
T019-04 Rev 08-25
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
Installation Steps
1. Identify suitable mounting location for the TireView LIVE (TVL) sending unit and repeater. See Figure 1.
NOTE: Location of the power source may impact the mounting location of the sending unit and repeater. Identify location of 5-pin ABS connector or lift gate battery prior to mounting the gateway. It is recommended to mount the gateway and repeater at least 4 feet from each other.
Suspension Placement
CAUTION: The repeater must be installed to help ensure proper operation of the TireView system. Failure to install the repeater could void warranty.
CAUTION: if trailer is equipped with slider box, all components and wiring must be mounted below the slider rail to avoid damage when suspension is moved.
Sending unit
RECOMMENDED PLACEMENT: on suspension cross member, lift gate housing, or battery box.
CAUTION: Do not mount gateway where tires can throw debris onto enclosure as this could cause damage.
Sending Unit
Repeater
Lift gate or battery box placement
Figure 1: Recommended sending unit and repeater locations.
CAUTION: Make sure location is suitable to route power wire harness to the gateway.
2. Using the TVL sending unit as a template, mark mounting hole locations and drill with a 3/8″ drill bit. See Figure 2.
3. Use supplied bolts, washers, and locknuts to attach sending unit to vehicle.
TORQUE mounting bolts to 8-10 ft.-lbs.
CAUTION: When mounting Sending Unit, you must utilize a strain relief cable tie with drip loop configuration and ensure the Weather Pack connector is facing downward. See Figure 3.
Figure 2
Strain relief cable tie
Drip loop
Face connector downward
Figure 3: TVL non-battery backup sending unit harness.
CAUTION: For Battery Backup Sending Unit,
connector should point down, and drip loop should be created with harness. See Figure 4.
Face connector downward
Drip loop
© 2025 Pressure Systems International, LLC. A Clarience Technologies Company.
Figure 4: Battery backup sending unit harness.
4
T019-04 Rev 08-25
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
Repeater
RECOMMENDED PLACEMENT: on the suspension near the tires being monitored. See Figures 1 & 5.
CAUTION: Avoid mounting the repeater where it is surrounded by metal (i.e., inside a cross member). This can prevent sensor signals from reaching the sending unit and will cause loss of data.
4. Mount the repeater using cable ties (included), bolts, or rivets. Repeater harness should be secured to factory wire harness or air lines with supplied cable ties and route towards the battery box. See Figure 5.
Wire Harness Connection
5. Locate the round 5-pin connector that supplies power to the ABS module. Unplug connector and install supplied harness in-line. See Figure 6.
6. If connecting to lift gate battery, connect ring terminals of the harness to the battery terminals, ensuring positive (+) and negative (-) leads are on correct terminals. See Figure 7.
7. Connect one lead of the harness to the Weather Pack connector on the sending unit harness, and the second lead of the harness to the Weather Pack connector on the repeater. Secure excess harness using supplied cable ties. Verify 2A fuse is installed in wiring harness fuse holder.
Figure 5 Figure 6
NOTE: The supplied wire harness has 2 preterminated Weather Pack connectors. One lead is longer than the other, but the connectors are electrically the same. Use the proper length lead for each component. See Figure 7.
8. Secure harness to factory wire harness or air lines with supplied cable ties.
ABS Harness Example
Ring Terminal Harness Example
WEATHER PACK CONNECTORS
© 2025 Pressure Systems International, LLC. A Clarience Technologies Company.
Figure 7
5
T019-04 Rev 08-25
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
Power on System
9. Apply power to the trailer using a tractor, Lite-Check device, or other portable power pack to verify status lights on equipment. See Figure 8.
TireView LIVE Receiver indicator light
LED Signal ACQUIRED
(Signal)
(Blinking)
NO LIGHT
RED
Check power connection
TireView LIVE Sending Module indicator lights
LED
SEARCHING for Signal ACQUIRED
(Signal) Signal (Blinking)
(Solid)
GREEN (GPS)
AMBER (Cellular)
TireView LIVE BBU (if equipped)
LED
Disconnected
Powered/ Charging (Solid)
RED
NOTE: If green or amber lights do not turn solid, move vehicle outdoors or to an area with better cellular coverage.
Install Decals
10. Consult vehicle owner operator, fleet owner, or management for decal placement. Clean surface prior to decal installation.
NOTE: Do not place decals on sending unit cover or obstruct sending unit barcode label.
Program Sensors to System
11. Use the mobile app (Goodyear® TPMS PlusTM, TireView LIVE, etc.) to program the system and install sensors.
Figure 8
© 2025 Pressure Systems International, LLC.
6
A Clarience Technologies Company.
T019-04 Rev 08-25
TPMS Sending Unit, Repeater and Harness Installation
Trailer Applications
Record of Revisions
Revision Number
Revision Date
By
A
October 23, 2024
CS
B
August 20, 2025
CS
© 2025 Pressure Systems International, LLC.
7
A Clarience Technologies Company.
T019-04 Rev 08-25
Pressure Systems International 4323 Interstate Way, San Antonio, TX 78219 USA Phone: 210.222.1926, Fax: 210.568.4221 www.psitireinflation.com
Visit www.psitireinflation.com/resources or scan this QR code for access to the latest revision of this manual.
© 2025 Pressure Systems International, LLC.
8
A Clarience Technologies Company.
T019-04 Rev 08-25
Documents / Resources
 |
P S I T019-04 TireView LIVE Sending Unit, Repeater and Harness and Repeater [pdf] Installation Guide Rev 08-25, T019-04 TireView LIVE Sending Unit Repeater and Harness and Repeater, T019-04, TireView LIVE Sending Unit Repeater and Harness and Repeater, LIVE Sending Unit Repeater and Harness and Repeater, Sending Unit Repeater and Harness and Repeater, Unit Repeater and Harness and Repeater, Repeater and Harness and Repeater, Harness and Repeater, Repeater |